Inline FabricationMidSouth Shooters SupplyRepackboxRotoMetals2
Titan ReloadingADvertise hereLee Precision

Tab Content
  • Harter66's Avatar
    Yesterday, 12:03 AM
    A friend had a SS Rossi M92 38/357 all of the 38s I tried fed like water through a hose just as fast as I could run it . I didn't try a WC . 357 however required a sideways feed and wiggle it acted like it was hanging the case mouth on a chamber...
    23 replies | 862 view(s)
  • Harter66's Avatar
    06-27-2022, 11:33 PM
    With the above and compared to an example I had I would agree with the others . The one I had would have likely been ok to shoot with 7.9257J ammo as the Metford type rifling groove was .318 . I ended up with a 8mm Mauser neck die and an...
    6 replies | 291 view(s)
  • Harter66's Avatar
    06-27-2022, 02:45 PM
    Harter66 replied to a thread Dies 7 mm in Helping Hands
    I'm not in need but it might be helpful to specify 7mm/757/Mauser , 7mm Rem express or 7mm RM . After many years I feel sure it would be for an RM buy wouldn't be surprised if it were a 7mm Mauser set .
    5 replies | 125 view(s)
  • Harter66's Avatar
    06-24-2022, 08:11 AM
    I believe #1 is more likely to be antimony wash .
    12 replies | 1970 view(s)
  • Harter66's Avatar
    06-20-2022, 04:42 PM
    I can't say in either case ........ I don't recall the Savage barrel having any markings and the gas gun I'd have to take apart to look . I want to say the 6.847 was Black Hole Weaponry , the 5R rifling isn't an exclusive to one maker . The...
    7 replies | 364 view(s)
  • Harter66's Avatar
    06-20-2022, 10:01 AM
    Been here . I've formed a lot of tight bolt brass that was freely extracted . It kind of depends on where it's tight . As long as it's not the neck it's good to go . The Savage bolt is in fact screwed on and fitted via the oval with flats key...
    24 replies | 760 view(s)
  • Harter66's Avatar
    06-18-2022, 12:04 PM
    When in doubt wash it out . I know you have had it apart , but Mom had a 1917 Colts I had apart and tinkered at that just seemed to grow dirt in everything that moved . I gave up an put it in a cake pan with a gallon of GI CLP with the grips off...
    13 replies | 433 view(s)
  • Harter66's Avatar
    06-16-2022, 10:52 PM
    Harter66 replied to a thread Places you have been in Our Town
    I've been south to San Antonio Tx and Bia San Quentin Baja (sounds more like canteen that the Cali prison) north to some little town on I-5 east of Vancouver and north of Seattle and Calgary AB . Baja Mexico Alberta Canada Washington State...
    47 replies | 1495 view(s)
  • Harter66's Avatar
    06-15-2022, 10:13 AM
    The NOE 279-124 is designed specifically for the 6.8 SPCII . The SPCII is the same but without the SAAMI throat and leade , it's slightly longer and shallower taper . Which is more in line with the original pre Rem SAAMI drawing . Barrels are...
    7 replies | 364 view(s)
  • Harter66's Avatar
    06-07-2022, 11:10 PM
    I hope my bench doesn't get the note about special brass and bad groups w/o checks . Read the paper thread in BP paper patch ......like 3x because the first time about 5% is going to stick and you'll be completely over loaded . The 45-70...
    10 replies | 512 view(s)
  • Harter66's Avatar
    06-06-2022, 06:14 PM
    Seems to me swaging something like PPC or X39 clan would be easier in a steel die . I've done a little bit of 6.5x50 Japanese from 243 down to a semi rimmed case . A little wet lube , a half stroke , relube , full length , and trim the head...
    10 replies | 424 view(s)
  • Harter66's Avatar
    06-01-2022, 09:02 PM
    Or LPP mag . 7-08 from 6.5 CM is about as close as you'll get and the neck will be short . In terms of higher MAP than the nominal 55-58kpsi the x57 and 06' clans aren't even being explored , it's the whole more with less deal where displacement...
    8 replies | 399 view(s)
  • Harter66's Avatar
    06-01-2022, 12:52 PM
    This is yet another useful thread . I got a bunch of Herco a year or so ago . I was thinking for 45 Colts , Dad loaded SWC in 45 ACP with it long ago and far away . I have a 45 S&W also that would benefit from it . Current data shows round...
    21 replies | 10162 view(s)
  • Harter66's Avatar
    05-31-2022, 07:59 PM
    Harter66 replied to a thread 10 gauge hulls in Helping Hands
    I wouldn't take it personally . I've been passively looking for about 6 years . I need a few to cut down to 2-9/16" . There just aren't many out there .
    10 replies | 480 view(s)
  • Harter66's Avatar
    05-31-2022, 10:45 AM
    The FEG and FN HP have a straight safety . I can see where that "dog leg" would cause a situation with a thumb . Sausage fingers ......pfft ..... Size 10 pinkie the other 3 and thumb share a size 14 and a 1911 is all but too far around . Bone...
    16 replies | 1042 view(s)
  • Harter66's Avatar
    05-30-2022, 05:20 PM
    Harter66 replied to a thread Lee dies in Reloading Equipment
    Sizers and seaters are marked . Unfortunately the others generally aren't . I've had a couple specifically Lee and even with pictures and all of the numbers they couldn't tell me what it was .
    3 replies | 256 view(s)
No More Results

Statistics


Total Posts
Total Posts
5,030
Posts Per Day
1.11
General Information
Last Activity
Yesterday 09:04 AM
Join Date
01-11-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check