MidSouth Shooters SupplyADvertise hereLee PrecisionRotoMetals2
Inline FabricationTitan ReloadingRepackbox

Tab Content
  • Harter66's Avatar
    Yesterday, 10:10 PM
    I once squashed so .360 RB out to 458 and loaded them like a 250ish WC , 4 in a Colts case for 600 fps . That out of a 7.5" Ruger . A stacked wad and something similar in your 444 case should due nicely . Hard to fight when you can't breathe . ...
    8 replies | 212 view(s)
  • Harter66's Avatar
    07-01-2022, 12:41 PM
    Well based on 757 and 25-06' you'll need the top of the Unique loads to get little groups . I ain't scared I cast 22,25,26,27, and 28 cal and have had good results with all of them . In 27 cal I run a 6.8 SPCII with the NOE 279-124 at 130...
    14 replies | 222 view(s)
  • Harter66's Avatar
    06-30-2022, 12:55 PM
    Welcome . A qualifier my 45 Raptor was actually cut with a 45 ACP reamer . I just necked up 1x 308 . 8mm , 9mm/35 cal , anneal , and up to .451 in the 460 dies . Back the flair die up about 3 turns as the brass is .2-.3" too long . Trim them...
    4 replies | 175 view(s)
  • Harter66's Avatar
    06-28-2022, 12:03 AM
    A friend had a SS Rossi M92 38/357 all of the 38s I tried fed like water through a hose just as fast as I could run it . I didn't try a WC . 357 however required a sideways feed and wiggle it acted like it was hanging the case mouth on a chamber...
    22 replies | 939 view(s)
  • Harter66's Avatar
    06-27-2022, 11:33 PM
    With the above and compared to an example I had I would agree with the others . The one I had would have likely been ok to shoot with 7.9257J ammo as the Metford type rifling groove was .318 . I ended up with a 8mm Mauser neck die and an...
    6 replies | 376 view(s)
  • Harter66's Avatar
    06-27-2022, 02:45 PM
    Harter66 replied to a thread Dies 7 mm in Helping Hands
    I'm not in need but it might be helpful to specify 7mm/757/Mauser , 7mm Rem express or 7mm RM . After many years I feel sure it would be for an RM buy wouldn't be surprised if it were a 7mm Mauser set .
    7 replies | 201 view(s)
  • Harter66's Avatar
    06-24-2022, 08:11 AM
    I believe #1 is more likely to be antimony wash .
    12 replies | 1993 view(s)
  • Harter66's Avatar
    06-20-2022, 04:42 PM
    I can't say in either case ........ I don't recall the Savage barrel having any markings and the gas gun I'd have to take apart to look . I want to say the 6.847 was Black Hole Weaponry , the 5R rifling isn't an exclusive to one maker . The...
    7 replies | 376 view(s)
  • Harter66's Avatar
    06-20-2022, 10:01 AM
    Been here . I've formed a lot of tight bolt brass that was freely extracted . It kind of depends on where it's tight . As long as it's not the neck it's good to go . The Savage bolt is in fact screwed on and fitted via the oval with flats key...
    24 replies | 788 view(s)
  • Harter66's Avatar
    06-18-2022, 12:04 PM
    When in doubt wash it out . I know you have had it apart , but Mom had a 1917 Colts I had apart and tinkered at that just seemed to grow dirt in everything that moved . I gave up an put it in a cake pan with a gallon of GI CLP with the grips off...
    13 replies | 444 view(s)
  • Harter66's Avatar
    06-16-2022, 10:52 PM
    Harter66 replied to a thread Places you have been in Our Town
    I've been south to San Antonio Tx and Bia San Quentin Baja (sounds more like canteen that the Cali prison) north to some little town on I-5 east of Vancouver and north of Seattle and Calgary AB . Baja Mexico Alberta Canada Washington State...
    47 replies | 1521 view(s)
  • Harter66's Avatar
    06-15-2022, 10:13 AM
    The NOE 279-124 is designed specifically for the 6.8 SPCII . The SPCII is the same but without the SAAMI throat and leade , it's slightly longer and shallower taper . Which is more in line with the original pre Rem SAAMI drawing . Barrels are...
    7 replies | 376 view(s)
  • Harter66's Avatar
    06-07-2022, 11:10 PM
    I hope my bench doesn't get the note about special brass and bad groups w/o checks . Read the paper thread in BP paper patch ......like 3x because the first time about 5% is going to stick and you'll be completely over loaded . The 45-70...
    10 replies | 529 view(s)
  • Harter66's Avatar
    06-06-2022, 06:14 PM
    Seems to me swaging something like PPC or X39 clan would be easier in a steel die . I've done a little bit of 6.5x50 Japanese from 243 down to a semi rimmed case . A little wet lube , a half stroke , relube , full length , and trim the head...
    10 replies | 440 view(s)
No More Results

Statistics


Total Posts
Total Posts
5,033
Posts Per Day
1.10
General Information
Last Activity
Yesterday 10:10 PM
Join Date
01-11-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check