MidSouth Shooters SupplyLee PrecisionADvertise hereInline Fabrication
RepackboxTitan ReloadingRotoMetals2

  • Old Caster's Avatar
    01-21-2022, 11:53 PM
    I have a Cabela electric scale that plugs in and it works well but you can not dribble powder in because it will make it out of adjustment. I don't know how much it cost because I got it in a group of supplies nor do I know if it is still...
    25 replies | 437 view(s)
  • Old Caster's Avatar
    01-18-2022, 11:36 PM
    It will not work for a 30/30 because they are larger and not based on a 30/06 cartridge.
    9 replies | 435 view(s)
  • Old Caster's Avatar
    01-16-2022, 11:11 PM
    My grandfather caught sparrows which we called chippies and cooked them with chicken feet in a pan of boiling oil. I don't know what kind of batter he put on the outside but it wasn't very thick. It was so crunchy that you could eat them and the...
    8 replies | 558 view(s)
  • Old Caster's Avatar
    01-15-2022, 11:32 PM
    3-600 at a time I would get a Lee 20 pound and use your other pot to feed it with liquid lead with a scoop ladle and you will be fine. If you want to do more, I like an older RCBS by far.
    19 replies | 490 view(s)
  • Old Caster's Avatar
    01-15-2022, 11:25 PM
    I would think that Bullseye shooters are in the minority anyway but many of us do it because we can make more accurate bullets than we can buy regardless the cost. In many pistols if not most a cast bullet is the most accurate possible. It just...
    89 replies | 2785 view(s)
  • Old Caster's Avatar
    01-14-2022, 12:22 AM
    Get yourself a 20 pound pot and use your 10 pound to premelt so you can just take a dipper and keep your 20 pounder filled without having to worry about changing your temperature.
    10 replies | 416 view(s)
  • Old Caster's Avatar
    01-14-2022, 12:06 AM
    Old Caster replied to a thread Softening Alloy in Cast Boolits
    I would not use any bullet with antimony in it. One of the BPCR guys did some experimenting with lead that was harder hoping for better accuracy and his problem was that when you get leading with no antimony it is simple to clean it out with a...
    23 replies | 567 view(s)
  • Old Caster's Avatar
    01-10-2022, 10:54 PM
    Old Caster replied to a thread White Label Lubes in Boolit Lube !
    I use only 2500 and bought some bricks and melted them down with a heat gun and put them in PVC of the right length while sitting on a steel plate. After putting them in the freezer overnight they came out easily. I also did it with BAC and...
    347 replies | 356819 view(s)
  • Old Caster's Avatar
    01-10-2022, 03:23 PM
    I bought a used 550 that looked like new and had primer flipping problems and just adjusted the part where you turn the turret and it took me several times to get it perfect but now works perfectly. Bear in mind that when you do this it is also...
    30 replies | 860 view(s)
  • Old Caster's Avatar
    01-09-2022, 09:54 PM
    I used these in a Model 10 Smith shooting IDPA matches because I could load them very lightly and still get power factor. I don't remember exactly what my load was or how fast they were but I remember around 550 or so and the recoil was so light...
    64 replies | 23098 view(s)
  • Old Caster's Avatar
    01-08-2022, 11:52 PM
    I bought 10,000 large pistol Wolf primers because they were about half the price of other primers. I sold them to all my friends for what they cost and all of us had problems with them an no one had problems with any other primers. Generally they...
    22 replies | 770 view(s)
  • Old Caster's Avatar
    01-04-2022, 10:38 PM
    Don, as soon as people have enough that they feel good about themselves they will stop buying completely because they won't use them up very fast, and that can make the prices go down rapidly. Most won't buy a case at a time like real shooters do.
    252 replies | 15549 view(s)
  • Old Caster's Avatar
    01-04-2022, 06:34 PM
    I have never had problems pressure pouring with any mold except a few that I have that are pretty much junk and I don't think any NOE molds are junk.
    13 replies | 644 view(s)
  • Old Caster's Avatar
    01-02-2022, 05:41 PM
    If I don't load a caliber with my 550 I would get my old round Lee out and I have never broken anything on it but if it feels hard to squeeze, check to see why. Probably a primer hole that needs to be enlarged because it is crimped. Never needed...
    56 replies | 2080 view(s)
  • Old Caster's Avatar
    01-02-2022, 05:15 PM
    I initially used a Herter model three for about 20 years and then bought a Lee plastic primer and then used it until I got an early 550. I never had any problems with primers going off until I bought some Wolf lpp about 20 years ago. It would be...
    41 replies | 1605 view(s)
  • Old Caster's Avatar
    12-30-2021, 12:24 PM
    Now I found Winchester small pistol primers for $60 a thousand close to St. Louis and they had a lot with no limit. Hopefully it is starting to come around.
    252 replies | 15549 view(s)
  • Old Caster's Avatar
    12-29-2021, 12:01 PM
    With ladle pour, you can whack the ladle on the edge of the pot constantly and it will always knock the dirt off. With bottom pour, you can't and is why the spouts on bottom pour always start to clog up even though you would think all the crud...
    46 replies | 2117 view(s)
  • Old Caster's Avatar
    12-28-2021, 08:04 PM
    Two local stores today around St. Louis had 1000 spp winchester for $79 and another store srp for $69 so I think things are turning just a bit but we still have 3 more years of what started the shortage so I don't know what to think. Each place...
    252 replies | 15549 view(s)
  • Old Caster's Avatar
    12-27-2021, 10:17 PM
    My choice happens to be 1.075 but I just looked at it and used it and since it worked in my accurized Beretta 92, my Browning Highpower, and my WWII Walther along with whoever has come to the range with me and have no bullets I haven't changed it. ...
    16 replies | 658 view(s)
  • Old Caster's Avatar
    12-25-2021, 09:38 PM
    I have a Waage on the side and I use a dipper to dump one pound at a time into my RCBS when the level gets to the right spot. Usually it is two pounds at a time. You don't need something as expensive as the Waage and could probably get by with a...
    15 replies | 718 view(s)
No More Results
About Old Caster

Basic Information

Age
77
About Old Caster
Biography:
Casting since 1966
Location:
Chesterfield Mo.
Interests:
shooting #1 senior olympics #2
Occupation:
retired

Statistics


Total Posts
Total Posts
803
Posts Per Day
0.18
General Information
Last Activity
Today 08:01 PM
Join Date
11-22-2009
Referrals
0

1 Friend

  1. subsonic subsonic is offline

    Boolit Master

    subsonic
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check