View Full Version : Tried my new mould
MiHec RCBS 45-270-SAA Brass Cramer style four cavity. Nice, easy casting, .455 diameter, 283-284 grains, straight wheelweights, air cooled. Should be some good shoooooooootin stuff.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/Picture006.jpg
Mal Paso
11-30-2010, 11:00 PM
Very Nice!
Dennis Eugene
11-30-2010, 11:17 PM
Nice lookin' bullets there Creeker. Dennis
1Shirt
12-04-2010, 09:39 AM
Elmer would have loved it!
1Shirt!
those are some darn nice looking bullets.
Andy
bbailey7821
12-04-2010, 10:56 AM
Those sure are nice looking. Good Job!
Thanks guys. The mould surely is easy to use. I ran it with a 4 cavity Lyman 429421 & a 2 cavity Ballist-Cast #928 under a Magma Master Pot. I used 50 pounds of wheel weights in a hurry I'm tellin' ya. HEE HEE
The Ballisti-Cast #928
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/Picture008.jpg
Cadillo
12-06-2010, 01:08 AM
That's a nice bullet. It would be perfect for my Bisely Blackhawk. I sure wish that I had paid attention and gotten in on that group buy.
Enjoy!
That's a nice bullet. It would be perfect for my Bisely Blackhawk. I sure wish that I had paid attention and gotten in on that group buy.
Enjoy!
BRP (BABore) can make you one up any time.
http://www.brp.castpics.net/P2.html
454-283 SWC
The bullet is 45 2.1's design which I believe is the one used in the MiHec GB. BRP can HP one cavity or multiple cavities of a mold. The only thing is he doesn't use brass, only aluminum for mold material.
MiHec RCBS 45-270-SAA Brass Cramer style four cavity. Nice, easy casting, .455 diameter, 283-284 grains, straight wheelweights, air cooled. Should be some good shoooooooootin stuff.
Nice looking boolits you've been cooking up!!! :cbpour:
If any of you guys would like to try this bullet before buying the mould I'll have some ready after the first of the year............Creeker
Cadillo
12-07-2010, 01:44 PM
[smilie=b:
BRP (BABore) can make you one up any time.
http://www.brp.castpics.net/P2.html
454-283 SWC
The bullet is 45 2.1's design which I believe is the one used in the MiHec GB. BRP can HP one cavity or multiple cavities of a mold. The only thing is he doesn't use brass, only aluminum for mold material.
I contacted them and asked, but unlike the four cavity version that was obtained through the group buy, they only market the two cavity version. I cast too many bullets to use a two cavity mould.
Just my luck! Maybe I'll take note in time the next time around.
BABore
12-07-2010, 02:23 PM
[smilie=b:
I contacted them and asked, but unlike the four cavity version that was obtained through the group buy, they only market the two cavity version. I cast too many bullets to use a two cavity mould.
Just my luck! Maybe I'll take note in time the next time around.
Are you sure it was me you contacted? I can make that mold in a 1C to 5C as a solid and put a HP in one of the cavities, or I can do a 2C or 4C all HP mold. I'm the only one here who takes mold questions
BRP 4 cavity HP mold pics:
453640 HP
http://i612.photobucket.com/albums/tt206/RobS01/BRP453640HPmold.jpg
http://i612.photobucket.com/albums/tt206/RobS01/Bottom.jpg
http://i612.photobucket.com/albums/tt206/RobS01/Side-HP-1.jpg
and a pic of them used for 45 acp:
http://i612.photobucket.com/albums/tt206/RobS01/BPR230HP.jpg
and a 5 cavity solid mold of the 454-284-SWC a 45 2.1 design and I believe the same design as the MiHec mold or close to it
http://i612.photobucket.com/albums/tt206/RobS01/cavities.jpg
http://i612.photobucket.com/albums/tt206/RobS01/topsprueplate.jpg
http://i612.photobucket.com/albums/tt206/RobS01/Moldinfo.jpg
Cadillo
12-07-2010, 08:20 PM
Are you sure it was me you contacted? I can make that mold in a 1C to 5C as a solid and put a HP in one of the cavities, or I can do a 2C or 4C all HP mold. I'm the only one here who takes mold questions
The Original Poster identified it as a MiHec mould. He said:
"MiHec RCBS 45-270-SAA Brass Cramer style four cavity. Nice, easy casting, .455 diameter, 283-284 grains, straight wheelweights, air cooled. Should be some good shoooooooootin stuff."
I had previously contacted MiHec by email after learning of the recently closed Group Buy for a four cavity brass mould for this or a similar bullet. They told me that they had two cavity moulds for the same bullet in either hollow point or flat nosed configuration, but that the four cavity models were all sold.
I'm not sure how you got thrown into the mix, but Welcome Aboard!
BABore
12-08-2010, 09:43 AM
From post #12 where you quoted RobS. It included my info and site.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.