Parts for Lyman #45 lubrisizer

[curator]

Where can I get a schematic drawing of the Lyman #45? I think I am missing the o-ring gasket on the pressure piston. It has been years since I used it last, now it won't pump lube except out the top. Any one know where to get parts?

[deltaenterprizes]

O rings available at auto parts store or hardware store.

[imashooter2]

Not really much of an exploded view, but here you go:

http://home.comcast.net/~imashooter2/Lyman_45.pdf

The pressure nut for the 450 and 4500 is the same. The O rings for the current presses will fit your nut.

[jcwit]

If you have an old orginal #45 lube/sizer it does not have an "O" ring on the piston, the orginal piston uses a brass ring. The piston for the #450 and #4500 however will fit and are available from Lyman. Go to their site and click on parts. If you end up ordering I would also get the threaded rod.

[94Doug]

I have one, I just need to look on another PC. I'll let you know what I come up with.

Doug

[Bad Water Bill]

I have 3 model 45s and they all have the new setup.

As far as the wax coming out of the top but not the bottom and it has sat around for a few years, now you have another job. Clean ALL the old wax out before you do any thing else. I had one that had set for 30 years and the wax was like a rock. Heat it with a hair drier till you see clean metal everywhere, yes even in the sizing reservoir or a chunk will come loose at the worst time.

Don't ask me how I know.:bigsmyl2:

[jcwit]

I have 3 model 45s and they all have the new setup.


Did you do the replacement with the newer "O" ring piston? I have 2 that I've upgraded to use the new piston.

Yes you're right Bill, he needs to heat things up and remove all the old lube.

[curator]

My thanks to you all! I have cleaned a couple of these over the years, so I have a pot big enough to boil the crud out of it I will order the "upgraded" piston and "O" ring set from Lyman. I actually like the #45 a bit more than the #450 which always leaks out of the bottom. I have thick gaskets under them and permatexed them to the bench and after a year or so they start to leak. My RCBS does not leak but I break a handle off every year. I use LBT "blue" almost exclusevly on bullets with gas checks. The others I tumble in LLA. I suspect the stiffness of the LBT lube is some part of the wear and tear my various lubrisizers experience, but its advantages outweigh the inconvenience.

[Houndog]

Curator,
Not trying to be a smart a**, but may I suggest you look into a heater for your lubrisizer? It can be as simple as attaching an Aluminum plate to the bottom of the unit with a wooden block under the plate for an insulator and sitting an iron set on low on the plate for a heat source or a drop light propped up against the lube reservoir. While I have not used the particular lube you do, the above setup with the iron makes my life a bunch easier when I use a hard lube.

[cephas53]

"It can be as simple as attaching an Aluminum plate to the bottom of the unit with a wooden block under the plate for an insulator and sitting an iron set on low " Good, simple idea, will work for me. Thanks

[cheese1566]

Heater, heater!
http://cheese1566gunsandstuff.shutterfly.com/130
Homemade that incorporates a Lyman cartridge heater. Oak blocks with tee nuts and the alum block traded by a fellow member. C-clamps on the bench for portability and storage.

I have the O-ring size written down somewhere if you need them. But like others said, I took the pieces to the hdwe store and found the ones I liked for a snug fit. No leaks. If you order a new piston, then get the pistons from Lyman.

[imashooter2]

"It can be as simple as attaching an Aluminum plate to the bottom of the unit with a wooden block under the plate for an insulator and sitting an iron set on low " Good, simple idea, will work for me. Thanks

I did the same with a piece of 10 gauge (.135) cold rolled steel I had laying around. No problem conducting the heat.

[TAWILDCATT]

I have two lyman 45,and never had a leak in the bottom.one I have had since they first came out.around 1945/6.also I have never broke one.to many are ham handed.or were the early users smarter.I know enuf not to strain the machine and break handles.I do use a hair dryer when its cool.my lube is an NRA type. I bought 50 lb in bulk yrs ago.[smilie=1:

[94Doug]

I did find my 45 manual in pdf form, 2 attachments. Anyone that wants it can email me.

Doug

[salide]

would like a copy could you put somewere on forum so we could find it thanks,,,,,, bill briggs tx

[JonB_in_Glencoe]

It's in a sticky...in this section...see the 5th post
http://castboolits.gunloads.com/showthread.php?t=34525

or just click here
http://home.comcast.net/~imashooter2/Lyman_45.pdf

[1_Ogre]

I have a Lyman 45 Sizer and have problems. The previous user didn't take very good care of it and the barrel that the lube fits in, the bottom where it threads into the base has the threads on the BARREL almost worn off. Other than that it works fine, but when you turn the threaded rod that forces the lube down, the darn barrel keeps backing out, then the lube is all over the place. I have tried cleaning the threads on the barrel and the base, but it keeps coming loose, FRUSTRATING. I have even used Locktite RED, but the threads on the barrel are too worn to stay put. Does anyone know where I can get a replacement barrel??????? I like the 45 over any of the UPDATES (hah), but have this one problem. Spare parts anyone?

[imashooter2]

Spare parts come from broken presses on these. I suggest you braze it.

[SteveK]

A friend just dropped off an old Lyman 45 for me to use BUT, its missing parts like the lube cap the ratchet/wrench .

PLEASE, Can anyone direct me to a parts supplier? I hate to toss this old boy out in the recycling.

[imashooter2]

The cap is not necessary. A 1/4 inch ratchet wrench will work for the pressure screw or you can get an original style wrench from Chapman.

[SteveK]

The cap is not necessary. A 1/4 inch ratchet wrench will work for the pressure screw or you can get an original style wrench from Chapman.

I just took it apart, cleaned it, and discovered that what you said about the cap is true, imashooter2... pretty much ornamental the cap is. Never heard of Chapman but I'll google it. I also determined that one vital thumb screw is missing but I'm sure the hardware store has a reasonable facsimile.

Thanks for your help!

[Pooch]

The cap is not necessary. A 1/4 inch ratchet wrench will work for the pressure screw or you can get an original style wrench from Chapman.

Yea, what he said.

[imashooter2]

I just took it apart, cleaned it, and discovered that what you said about the cap is true, imashooter2... pretty much ornamental the cap is. Never heard of Chapman but I'll google it. I also determined that one vital thumb screw is missing but I'm sure the hardware store has a reasonable facsimile.

Thanks for your help!

First item at the top of the page...

http://www.chapmanmfg.com/OrderParts.html

[jcwit]

the cap is not essential true, but it does help keep the rod centered.

Harbor Freight also has a ratchet wrench available. 3 bucks IIRC

[jcwit]

the cap is not essential true, but it does help keep the rod centered.

Harbor Freight also has a ratchet wrench available. 3 bucks IIRC

[imashooter2]

the cap is not essential true, but it does help keep the rod centered.

Harbor Freight also has a ratchet wrench available. 3 bucks IIRC

True enough. Fortunately the cover for the 450/4500 fits. First item on the list:

http://www.lymanproducts.com/store/page150.html

While you're ordering, the O ring pressure nut (2nd item down) is a significant upgrade if your 45 still has the brass skirt nut.

[erikk]

Well after over 50 years I finally broke the handle on my Lyman #45 lube sizer...Any ideas or info where I might find a replacement??
Thanks

[fryboy]

Well after over 50 years I finally broke the handle on my Lyman #45 lube sizer...Any ideas or info where I might find a replacement??
Thanks

fellow member jonB made a few , if he still has any left or not i dont know ... pm him and ask would be my first suggestion , second would be to post a want to buy add ,good luck amigo

[waksupi]

Well after over 50 years I finally broke the handle on my Lyman #45 lube sizer...Any ideas or info where I might find a replacement??
Thanks

I've had a section of 3/4" pipe epoxied to the end of mine for the last 25 years or so!

[JonB_in_Glencoe]

Well after over 50 years I finally broke the handle on my Lyman #45 lube sizer...Any ideas or info where I might find a replacement??
Thanks


fellow member jonB made a few , if he still has any left or not i dont know ... pm him and ask would be my first suggestion , second would be to post a want to buy add ,good luck amigo

I don't have anything for sale right now. here is a link to the thread to show you how I built them and maybe it'll give you a few ideas to make your own...Be sure to read post 31, it has photos of the improved version I ended up Making 20+ units of for resale.

http://castboolits.gunloads.com/showthread.php?107488-Do-you-have-a-broken-non-working-Lyman-45-lubsizr&highlight=

[44Vaquero]

Follow this link to a PDF with an excellent set of 1950's instruction's. http://stevespages.com/lymanom.html

[1_Ogre]

You might try eBay aka crapbay. Sometimes you can find one for sale for parts pretty cheap

[MtGun44]

No link found in post #30

Bill

[44Vaquero]

Bill, the link is in 31.

[JonB_in_Glencoe]

No link found in post #30

Bill

thanks Bill,
Link added

[Alvin]

Here is a picture of the Lyman 45 I'm currently in the process of modifying. I got the unit in an estate sale, and it was in excellent shape with just a few paint chips here and there. I'm currently cleaning this up and making a few modifications. All I planned to do was clean it before selling since I don't need another sizer. After reading through some threads, I decided to make a quick few changes so that I maybe able to get a few extra dollars but also give the buyer a good sizer that is ready to go with a few convenience modifications. I started by mounting it to an extra piece of aluminum I had left over in the garage, that way the buyer can decide if they want to mount it directly or just clamp it when they use it. I added spacers because I heard a lot of good things about people using an old soldering iron to use as a heating source vs. having to buy a Lyman heater. You can see it sticking out on the left side.

What I'm actually going to do is buy an old coffee maker for $5 and use that as my heating element (stole idea from someone on the board I believe). I'll open the bottom up, and route the heating element under the sizer. My engineer friend has told me about something that'll help route the heat where I want it to go. The coffee maker will also allow the user to setup the heater to start before they plan on sizing, which means they are ready to go when they get there. It's also safer then using a soldering iron.

Don't sweat the cap and wrench too much. The wrench you can pick up any where, and if I remember correctly someone on the board knows how to make them. The may be able to make one for you, or give you directions on how to. 8913389134

[uscra112]

If you use a ratchet, make sure it's a six-point. Don't ask me how I know.......

[ranger1962]

i need the threaded rod for a model 45. where can i find one ?

[fryboy]

lyman

( fairly cheap too )

depending upon which cap you have you may have to enlarge the hole on the cap a bit but other than that ...

"

Replacement Parts 4500/450 - ( 9) Pressure Screw
2990559
$6.00




fine time to pick up a new pressure nut or o-rings as well



Replacement Parts 4500/450 - ( 2) Pressure Nut (with two o-rings) formerly 2990146
2990708
$5.00





http://www.lymanproducts.com/store/page150.html

[Greg S]

I need a guide rod. My left one is bent at two places. I tried to straighten it but... its straighter but still rubs/ binds. If anyone has some spare time and a mini lathe, I've got all the pertinent measurements, i just don't have access up here in AK.

[JonB_in_Glencoe]

I need a guide rod. My left one is bent at two places. I tried to straighten it but... its straighter but still rubs/ binds. If anyone has some spare time and a mini lathe, I've got all the pertinent measurements, i just don't have access up here in AK.
"bent at two places" ...yikes !!!

I have an original one, .... pm me for details

http://i640.photobucket.com/albums/uu127/JonB_in_Glencoe/slide%20rod_zpskroz3lsn.jpg (http://s640.photobucket.com/user/JonB_in_Glencoe/media/slide%20rod_zpskroz3lsn.jpg.html)

[TenTea]

Anyone have a source or part number for the Lyman 45 return spring?

Mine machine is getting the droops.

Seems like it was mentioned by a fellow forumite in past years...thanks!

I don't see 45 springs offered by Lyman at this time.

[imashooter2]

Hardware stores have a variety of springs to choose from. This isn't a critical part, just pick something close.

[TenTea]

Hardware stores have a variety of springs to choose from. This isn't a critical part, just pick something close.

Yes, understood.
My spring *fits* now, but it don't hold the handle up. :shock:
I was hoping maybe somebody had recently "been on this bus before"...and had specific info.
That way, I could get something delivered to my mailbox!
The hardware store in my village closed up years ago, and it's eight miles over rough country, by horseback, to the village west of us, and the nearest general store.
:Fire:

[imashooter2]

Yes, understood.
My spring *fits* now, but it don't hold the handle up. :shock:
I was hoping maybe somebody had recently "been on this bus before"...and had specific info.
That way, I could get something delivered to my mailbox!
The hardware store in my village closed up years ago, and it's eight miles over rough country, by horseback, to the village west of us, and the nearest general store.
:Fire:

Ah! Here it's 3 minutes over paved road to a choice of stores. A man kind of gets used to his own existence...

[TenTea]

Ah! Here it's 3 minutes over paved road to a choice of stores. A man kind of gets used to his own existence...

Good to have options, I always say...

You sir, are a fortunate man, indeed. :!:

[JonB_in_Glencoe]

Anyone have a source or part number for the Lyman 45 return spring?

Mine machine is getting the droops.

Seems like it was mentioned by a fellow forumite in past years...thanks!

I don't see 45 springs offered by Lyman at this time.
PM sent