Not liking the straight stock on my new Marlin 44 Could I use a 336 pistol grip stock

[chutestrate]

Was thinking about possibly changing the stock to a 336 pistol grip stock, and then trying to match hardware as well. Has anyone done such a conversion? The recoil is knocking the hand holding the lever pretty hard and after a few shots it's painful. Thought either changing the stock and hardware or just getting a bigger loop lever.

[Shell knob]

It will depend on lower tang. Not sure about marlins, but early winchesters had a drop in the lower tang.

[farmbif]

on the 336 you could modify it with a pistol style stock, lower tang/trigger plate and curved lever but I'm not sure on the 1894. those parts might be real hard to impossible to find. the only 1894 I have with pistol style grip is an 1894FG 41 mag and its not a very common gun

[Dan Cash]

Before you spend money, try gripping the lever outside of the loop while the trigger finger does its thing.

[dverna]

Try a shooting glove. If necessary, cut half of the trigger finger part of the glove off

[floydboy]

Chutes, I have a 336 PG I was considering converting into a straight grip. I've done some research and am unclear if the lower tang/trigger plate and the finger lever will interchange from a 94 to a 336. Some evidence suggest they might. The 95 and 336 will interchange. I would be willing to swap it they would change. My rifle was made in 2000.

Thanks, Floyd

[cwtebay]

Or.... drop your load down to reduce recoil?

Sent from my Pixel 5 using Tapatalk

[Bazoo]

336 and 1894 trigger plates and levers are not interchangeable. Pistol gripped 1894s were extremely scarce. I think the 1894FG was the only one that had a pistol grip.

[FergusonTO35]

Before you spend money, try gripping the lever outside of the loop while the trigger finger does its thing.

This 100%. I only keep the middle finger inside the loop because I have big hands and it gets crowded otherwise. You can still work the lever quickly and can use the thumb to assist by pushing the top of the lever down.

[JimB..]

Find yourself a 336 in 44mag. They are scarce, but I don’t think terribly expensive.

[chutestrate]

Thank you for all the suggestions, and guidance

[pietro]

.

Most Marlins issued with a PG stock have curved lower tang surfaces that give a distance from the top tang about 1/2" more than a straight tang gun - just like most Winchester 92/94 leverguns.

Further, the straight lever would need to be swapped out for a curved lever - which are interchangeable on the fit to the receiver, but not to the tangs.

On a straight grip Winchester Big Bore 94, I was able to install a PG stock and a curved lever (because I got a fancy Centennial checkered PG stock @ a funshow for a smoking deal - $50) - but after installing the PG stock, there was a good sized hollow area between the closed lever and the PG contour, because the straight lower tang wasn't large enough to fill the inletting void - so, I filled the void with a fitted piece of walnut that I shaped & finished to match the "new" PG stock.


.

[murf205]

Go to rangerpointstore.com. They list all kinds of levers for Marlins and they offer 5 different styles. Maybe you can find one that you can get your paw to work with. I searched "glove loop levers" and they came up.

[farmbif]

saw suggestion to just get a 336 in 44 mag. first they are not real common. 2nd, not too many were made because it was a flawed design and they just didn't function very well. I believe most that are put up for sale because they dont function very well.
a loop lever is probably the easiest way to solve your problem

[JimB..]

saw suggestion to just get a 336 in 44 mag. first they are not real common. 2nd, not too many were made because it was a flawed design and they just didn't function very well. I believe most that are put up for sale because they dont function very well.
a loop lever is probably the easiest way to solve your problem
The design isn’t flawed, it’s just beefier and longer than it needed to be. There were some feeding problems with some rifles, but aren’t there always? Pretty sure it was discontinued when the 1894 was introduced.

[Kestrel4k]

My 336-44 has always functioned perfectly, and is the most accurate lever action I have ever worked with. My buddy sold his for $1500 a year or two ago, FWIW.

[farmbif]

thats good news. I always desired one but someone who knows a lot more than I do told me what I had written about the 336 in 44 mag. I sure do like the looks of that gun with the saddle ring.

[FredBuddy]

Like Don said, I got a glove from WM
that has 'ribs' on the back of the fingers
and I cut the end of the trigger finger
off. Works great. Now I gotta find a
pair in camo. I also leave my pinkie
outside the lever.

[Bloodman14]

I actually checked out Rangerpoint; DANG!!! I know some of you have mixed feelings concerning 'tactical' leverguns, but I am just a bit enthusiastic!