Ruger Single six un-conversion parts needed.

[BossHoss]

Can anyone tell me the parts list needed to un-convert a Single six from from the Transfer bar conversion? I bought one and did not receive the Original OM parts.

It was dirt cheap, clean and pretty withe WMR cyl also. I would like to un-convert it back to OM standard.


Boss.

[FergusonTO35]

Good luck with that! I would start scrounging Gunbroker and Fleabay, and be prepared to spend some serious coin.

[pietro]

.

* OM hammer
* OM cylinder pin
* OM cylinder stop
* OM cylinder stop spring
* OM transfer bar
* OM trigger
* OM trigger return spring
* OM pawl

IME, obtaining these hen's-tooth parts today will most likely cost what you paid for the converted Single-Six.

.

[contender1]

Uhh, the list above is a little incorrect. There is NOT an "OM transfer bar" !

When Ruger does the safety transfer bar conversion, they add the transfer bar. It was not part of the original design.

I may have a complete set of re-conversion parts. PM me.

[MT Gianni]

I was under the impression that Ruger kept the old parts when they did the conversion. Good lick with your search.

[FergusonTO35]

Ruger claims to return the old parts when the conversion is done. Now, it wouldn't surprise me if some employees pocket them to sell for big bucks. For the OP, it might be easier and even cheaper overall to sell the current Single Six and buy one that was never converted. There are quite a few of them out there.

[BossHoss]

HI,

I got this convertible really cheap. If it has to stay converted until I stumble across the OM parts, so be it.

There has to be a junk drawer somewhere full of these. lol.

[BK7saum]

Good luck, but I doubt there are many parts out there, unless some boutique manufacturer made then to "un-convert" ruger handguns.

Ruger was the only one doing the conversion and it is my understanding that they never returned the old parts. So i doubt there are any parts available.

[Ickisrulz]

Good luck, but I doubt there are many parts out there, unless some boutique manufacturer made then to "un-convert" ruger handguns.

Ruger was the only one doing the conversion and it is my understanding that they never returned the old parts. So i doubt there are any parts available.

They have always claimed they'd return the old parts after doing the conversion.

https://ruger.com/pdf/safetyOfferAd.pdf

[BK7saum]

Thanks for the correction. I was always told that they did not return the parts. How old? (what date) is that add from?

[BK7saum]

If correct according to the add, then there should be parts out there. I was unaware of the offer of parts being returned.

[gmsharps]

Years ago I had a couple of old model rugers returned for the conversion and both had the old parts returned to me in a sealed plastic bag. I still have them in my shop somewhere.

Gmsharps

[G W Wade]

i returned my SBH in the early 80's because I hoped the new parts and retiming would make things better. Had a lot of rounds downrange. Came back with a regular hammer instead of the wide Semi-beavertail it came with. But I did get the origional oarts in a bag. IMHO I think a lot of people threw them away with the box! GW

[Ickisrulz]

Thanks for the correction. I was always told that they did not return the parts. How old? (what date) is that add from?

It is a current offer that can be found on the Ruger website under safety announcements.

[contender1]

Ruger has been offering the transfer bar safety upgrade for MANY years. And they do return the original parts, UNLESS Ruger determines them to be unsafe. (Broken notches in the hammer or a broken trigger tip.) There has been many "internet stories" of Ruger keeping the parts,, but none have been verified. Ruger has a special bag, with printing on it, just for the OM parts they remove & return.
That said, often, when they would return a gun after the addition of the transfer bar,, the OM parts would be in a bag, AND under the folded cardboard flap in the return box. MANY people never looked for the parts, and "threw away the box."

I have been in touch with the OP, and I have a spare set of parts if he chooses to get a set.

I have found OM parts sets on gun show tables, or bought them from a person who had the conversion done & didn't want the parts.