PDA

View Full Version : Elmers Bullseye 44+p loads



Bazoo
04-24-2022, 10:10 PM
I was reading sixguns and happened to see a load of 6.5 bullseye under his bullet in 44 special cases. Anyone use this load? Anyone know what pressure it runs at? Anyone know anything?

I’ve seen 6.0 grains bullseye recommended before. Anyone use this? Anyone offer pressure?

oscarflytyer
04-24-2022, 11:03 PM
That would def be a "giddy up" load in modern 44 cases, according to published data. 44 Mag shows max 6.0/250. Max looks like ~5.5ish for 44 SPC, looking at Load Data.

6.5 gr BE in a 45 Colt w/ 250 grn bullet is about max published. Saw one load which is 7.0. For 45 Colt, the 6.5/250 is a traditional load equiv. And 45 Colt is supposed to be tad hotter than 44 SPC. (FWIW, I once goofed and mixed BE for Unique/old square cans look almost alike. I loaded 8.5 grn BE/250 grn! {was SUPPOSED to be Unique!} - It was H O T!!!! What I would consider a Proof Load! I shoot 6 in a Uberti SA - and was impressed after I figured out what I did/also why I say it is like a proof load. Also shot a cylinder in the NM BH - still HOT!)

I would guess that the load in Sixguns was in balloon head cases, which have a tad more case capacity, and what Elmer worked with a lot. I MIGHT shoot 6.5/250 in a 44 Mag if I worked up to it in a SBH carefully, but zero reason to shoot it in any 44 SPC for me. My go to (still considered 'up there') is the Keith 250 and 7.5 Unique. But all my 44 SPCs are NM BH or various Smith N Frames. And BE is def hotter by about ~2 grsn diff than Unique in my experience (ie: N grns of BE is ABOUT equivalent to N+2 grns Unique, IN THE BIG BORES - 44/45 bores - again, only in my experience...)

Bazoo
04-24-2022, 11:35 PM
I appreciate the reply and remembering of ballon head cases. I believe it was 1930 that he was using that load, so certainly ballon head cases.

nicholst55
04-25-2022, 12:59 PM
Elmer did a lot of by-the-seat-of-his-pants reloading, too, especially in his early days. I have read that he was casting lightweight .458" bullets for the .45-70 and loading them for his .45 Colts, when he was pushing the limits of that cartridge (and the existing guns).

ddixie884
04-25-2022, 08:07 PM
Alliant on line data is .45Colt 250gr 7gr BE. .44spl 250gr is 5.3 BE. but that is probably 15K for .45Colt and 14K for .44spl..............

Outpost75
04-25-2022, 11:29 PM
I would not shoot any of Elmer ' s old published loads. Other than a very few tested for him and validated by the powder companies, the great majority fall into the category of adventurous experimentation. I see no advantage to using .44 Special loads in modern .44 Magnum revolvers. I do enjoy .44 Magnum loads of reduced power which approximate .44 - 40 or .44 Special energy. Larry Gibson pressure tested those loads, which have been highly satisfactory. I believe he has also tested. 44 Special loads for the Ruger flat tops, which do exceed the SAAMI MAP for the .44 Special, but don't exceed about 20kpsi, being safely within design limits for the modern Italian Colt clones.