Miroku Winchester 1892 Ltd Ed.

[PeteB]

Just bought my first Winchester, a Miroku 1892 Limited Edition in 45 LC. Does anyone make a peep sight to fit this Tang Safety gun? Pictures would be appreciated.

[badguybuster]

You can have a williams sight installed. 2 holes 6-48 are drilled and tapped into the left side of the frame

[PeteB]

My 1892 Ltd Ed has engraved sides to the action and I don't really want to be drilling holes in it or covering it up.

[NSB]

Is the tang drilled and tapped? You can put a Marbles adjustable tang sight on the gun if it is. If it’s D&T then check out Brownell’s or Midway for a sight.
https://www.midwayusa.com/product/1005885753

[Baltimoreed]

Found a photo of a tang sight on a miroku at Paco Kellys website. Its a 1886 but might work on a 1892. Can’t post photos here.

[HWooldridge]

I have an old El Tigre in 44-40 and mounted a Marble tang sight rather than a receiver mount. The peep is sighted at 200 yds and the barrel sights at 50 yard (although they will flip up for those 1000 yd "Quigley" shots <LOL>).

[farmbif]

yeah that tang safety gets in way of mounting a tang sight. but that is a beauty of a rifle. Marbles makes about the shortest base for a tang sight ive seen. I'm not sure if it will fit yours or not. but there are also a few fairly new companies that are making very high quality tang sights, might be worth contacting them see if they have worked out solution for these newer winchesters.

[Baltimoreed]

Duplicate

[veeman]

Is it D&Ted on the top of receiver? Could get a Skinner peep. I have a few on 94's and 86's.

[meh]

Marbles makes a tang sight for Miroku-made Winchester 1892s. Hopefully your limited edition has the small hole drilled and tapped in front of the screw that holds the buttstock on. You’ll order a base and screw set. The actual sight depends on what range of adjustment you want/need.

[danmat]

Marbles makes 1 for your 92 I got mine from Midway.
Product #: 526620 Manufacturer #: 995024 UPC #: 871373004748 screw set #24
Product #: 465055 Manufacturer #: 009802 UPC #: 871373003024 Marble's Tang Peep Sight Browning 1892, Winchester 1892 with Tang Safety Steel Blue

Here you go, fit my Miroku 92 fine, My wood on tang was a little proud base fit between the wood tight I never drilled and tapped the front hole 4 yrs ago still aint moved.

Dan

[Castaway]

Marbles is the way to go. Not only elevation, but windage adjustable too. The underside of the sight that mounts on the tang is concave and nestles on the rifle tang. I use mine without having had to drill and tap. If the tang screw is snug, the sight isn’t going anywhere. Another selling point with Marble, if you call, you get a real person, friendly advice and free service on any rebuild

[PeteB]

That's really useful info Dan, thank you.

[PeteB]

Any thoughts on the Marble Arms Bulls Eye sight? It replaces the Buckhorn standard sight.

[Gray Fox]

Skinner also makes a barrel mounted aperture sight that replaces the rear sight. GF

[boommer]

I put the Bulls Eye on my 73 for me didn't work well for my eyes but my shoot'n buddy has better vision and don't wear glasses and he really liked it.

[Randy Bohannon]

The new Marbles sights I have seen are garbage, cheap pot metal and sloppy. Nothing compared to their heyday good stuff. I have been through about every iron sight made,you are challenged with the tang safety on the new 92’s if the tang is where you want the rear sight. The best and perhaps the most expensive route is to do the MVA Pope Style/ Marbles tang sight, you will need one hole D/T’d for the front base screw. If I was serious about getting the best out of the rifle without a scope I wouldn’t hesitate to use MVA anywhere I can make them fit.

[Castaway]

Randy, can you be more specific about the challenge with the tang safety?

[Randy Bohannon]

Spacing for mounting holes on the tang with the safety is very short unlike the 1873’s which are D/T’d . So the MVA is on a short base using the screw at the back of the tang is replaced with a longer screw,comes with the sight and a new hole D/T’d is needed to secure the front of the base behind the safety.

[Castaway]

Curiosity satisfied. I have a Marbles tang on my Miroku 92 and there’s no problem at all with the sight base and rifle tang fit. It’s a non-issue.

[danmat]

Randy is right they are not as robust as the older ones but i have not had a problem with mine but i will say I dont shoot the snot out of it either.
I have several leverguns with these sights, my marlins usually carry low power variable scopes as my eyes are failing me rapidly.
Another option i just received but have not had time to mount and check yet is this,https://pearsonstacrails.ecwid.com/ i am going to give some red dots a try on my browning 92s and muzzle loaders.

[swOhioMatt]

Can you remove the tang safety and just use the hammer half cock for the safety? A tang sight would then likely cover the hole left behind.

[Jeff Michel]

No half cock, rebounding hammer.

[PeteB]

Marbles makes 1 for your 92 I got mine from Midway.
Product #: 526620 Manufacturer #: 995024 UPC #: 871373004748 screw set #24
Product #: 465055 Manufacturer #: 009802 UPC #: 871373003024 Marble's Tang Peep Sight Browning 1892, Winchester 1892 with Tang Safety Steel Blue

Here you go, fit my Miroku 92 fine, My wood on tang was a little proud base fit between the wood tight I never drilled and tapped the front hole 4 yrs ago still aint moved.

Dan

Thanks Dan, I ordered the parts you listed from a dealer in Germany - Waffen Ferkinghoff, took just over a week and arrived today. The fit is great and only need to use the one screw hole with an extended tang bolt. Cost around £150.

[PeteB]

Photos of Marble Arms sight attached:-

296349

296350

296351

[BFJ]

Nice looking rifle. Sight looks great. Nothing like good help.

[danmat]

Glad it worked out for you. I like mine.
I like these on pistol cals. there are better sights for alot more money, but these handle my plinking out to 150 yards.
Dan