View Full Version : Cleaning sizing die
JodyPenny
01-23-2022, 03:10 PM
What do you use to clean the lube out of your sizing does? I have a problem with it building up and making everything sticky.
Bakebfr480
01-23-2022, 03:13 PM
Disassemble it and run a cleaning patch saturated with alcohol through it.
Char-Gar
01-23-2022, 03:54 PM
Disassemble it and run a cleaning patch saturated with alcohol through it.
^^^^^^^ correct answer
Shawlerbrook
01-24-2022, 08:13 AM
Good advice above ! I used brake cleaner, but there are many solvents that work.
Sasquatch-1
01-24-2022, 08:26 AM
I use a hairdryer to soften things up and then use acetone for the final clean up.
ps Take the O ring off before cleaning.
georgerkahn
01-24-2022, 09:38 AM
What do you use to clean the lube out of your sizing does? I have a problem with it building up and making everything sticky.
While I cannot disagree with the solvents mentioned in above posts, I have been a user of Mineral Spirits. In my experience, this -- complemented with a bit of brushing and passing a patch or two through -- gets my dies quite clean! Kindly note that I use the "old" mineral spirits -- petroleum based with quite the odour. I bought a (blue) can so labeled, but quite clearly NOT the same stuff at Lowe's not that long ago which did not work well at all. Hence -- if you wish to try using this solvent, make sure yours is the paint thinner old stuff :).
geo
Rcmaveric
01-25-2022, 01:29 AM
Disassemble. I use WD-40 with brass brush. Clean all the excess out. Wipe a little sizing oil on the inside with a quitip. Then on the outside Boesheild for the body or Fluid Film. My tools are in the garage and preventing rust is important.
Thinks for reminding me. I need to go clean my dies and guns. Everything got rusty in the move snd its driving me nuts. But i still jeed to organize the shop. Owe were to begin. I need an assistant or aprentice.
Sent from my SM-G991U using Tapatalk
+1 with the mineral spirits. Use Q-tips, too.
Winger Ed.
01-25-2022, 08:02 PM
I've never had much problem with build up in a sizer die, but the seating die would accumulate lube rather fast & often.
For both, I run a nylon bore brush up in it to break the goo loose, then wrap a patch around it and do it again to get the mess out.
It's quick, I leave the die in the press, and seems to do a good job for me.
When I'm done, they get a good deep cleaning, then go into storage.
Outer Rondacker
01-25-2022, 08:03 PM
All these methods work well. My buddy drops his in the ultra sonic cleaner. Claims it works the best.
Me carb or brake cleaner then some patches. But I not had to clean one in a while since PC.
brassrat
03-19-2022, 10:52 AM
Just don't boil in vinegar unless you want a Lee die that has a blued finish like a gun.
pworley1
03-19-2022, 02:52 PM
I use Ed's Red
Randy Bohannon
03-22-2022, 05:23 AM
Mineral spirits with enough ATF to color it pink, good for paint brushes and dies, cleans and leaves some protection.
iron brigade
03-22-2022, 06:09 AM
Kroil works well for that
jlb300
03-23-2022, 03:27 PM
I also use the break cleaner or carburater cleaner and a few Q-tips, taking off the O-ring first, then a towel with a little gun oil on it to coat it so it slides in easily. No problems with that method.
scratcherky
08-05-2022, 02:57 PM
I use Break Free.
gifbohane
11-05-2022, 11:40 AM
I usually remove the de-priming pin with shaft from the die while leaving it on the Redding turret and clean the die right there.
Anyone see a problem with that?
nicholst55
11-06-2022, 09:33 AM
I usually remove the de-priming pin with shaft from the die while leaving it on the Redding turret and clean the die right there.
Anyone see a problem with that?
That should work just fine, although you may get goop all over your press.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.