SwedeNelson
01-17-2009, 05:36 PM
Have had a problem with my Lyman 450 Lube/Sizer.
It has seen better days. The ram is real loss in the
body of the press. Couple that with a top punch that
has a small shaft and you can get some very bent bullets.
Have some real nice 6.5mm bananas. Not to mention
The problem I have had with it “Bumping” up the noise
of just about any 22Ca. I size in it.
So I tried the LEE push through dies. I really like the way
they work, great to size but hate the mess to lube them.
Doesn’t bend or bump up the noise of your bullet.
On the right track.
A couple of years age seen a Meacham push through
Lubrisizer for black powder cast bullets on the net.
Called Meacham and they no long make them and just
Made them for larger stuff any way.
So I got out my LEE push through die a Redding neck
size die and my calipers and went to work. Redding makes
Neck Sizer Bushings from .185 to .365 – That should cover
Every thing that I have been able to bend or bump up!
http://i69.photobucket.com/albums/i80/swedenelson/Picture070-1.jpg
Built a prototype last week. Works great as a sizer but
need to come up with a better lube system. Made it for
22Ca. and it will size from .223 to .226 by just changing
the bushings.
http://i69.photobucket.com/albums/i80/swedenelson/Picture068-1.jpg
http://i69.photobucket.com/albums/i80/swedenelson/Picture069-1.jpg
The lube reservoir is a manual bearing lubber
from McMaster Carr. It was cheap and got me started.
Have a reservoir designed that will hold a full stick and it
will be my next project. All the same I think the lube will
have to be a softer lube than what I have been using..
Any one use a softer Felix Lube?
Swede Nelson
It has seen better days. The ram is real loss in the
body of the press. Couple that with a top punch that
has a small shaft and you can get some very bent bullets.
Have some real nice 6.5mm bananas. Not to mention
The problem I have had with it “Bumping” up the noise
of just about any 22Ca. I size in it.
So I tried the LEE push through dies. I really like the way
they work, great to size but hate the mess to lube them.
Doesn’t bend or bump up the noise of your bullet.
On the right track.
A couple of years age seen a Meacham push through
Lubrisizer for black powder cast bullets on the net.
Called Meacham and they no long make them and just
Made them for larger stuff any way.
So I got out my LEE push through die a Redding neck
size die and my calipers and went to work. Redding makes
Neck Sizer Bushings from .185 to .365 – That should cover
Every thing that I have been able to bend or bump up!
http://i69.photobucket.com/albums/i80/swedenelson/Picture070-1.jpg
Built a prototype last week. Works great as a sizer but
need to come up with a better lube system. Made it for
22Ca. and it will size from .223 to .226 by just changing
the bushings.
http://i69.photobucket.com/albums/i80/swedenelson/Picture068-1.jpg
http://i69.photobucket.com/albums/i80/swedenelson/Picture069-1.jpg
The lube reservoir is a manual bearing lubber
from McMaster Carr. It was cheap and got me started.
Have a reservoir designed that will hold a full stick and it
will be my next project. All the same I think the lube will
have to be a softer lube than what I have been using..
Any one use a softer Felix Lube?
Swede Nelson