300 Blackout Powder Coated - NOE suggestions

[brown bass hunter]

Looking for suggestions on NOE boolit molds for 300 BO subsonic. I plan to powder coat and shoot subsonic. I am looking at NOE molds, but would look at other brands. Probably looking for 200+ grain molds. I plan on firing these in a Ruger American Ranch rifle.

Thanks for any experience with these

[fatmanunited]

Got to get the taco bullet

Sent from my SM-G988U using Tapatalk

[Conditor22]

https://noebulletmolds.com/site/shop/308-311/311-242-fn-j3/311-242-fn-j3-4-cavity-pb-whisper/
I use this on with the GC option but don't use a GC.

This is a tac driver in an H&R 300 AAC BO with a can, good out past 100 yards, and hits like a tank Subsonic over some 700X

[BJK]

This mould was suggested to me but I don't have it in hand yet. I ordered mine with the GC option but it's available without. And just because it has the option for a GC that doesn't mean it must use one. Somewhere in that thread far below I link to a chapter of a book where velocities of cast bullets is discussed. I think I should be good to go even supersonic with that bullet and with a GC almost certainly. But I'm new to this and it's just based on what I read and what was suggested to me.
https://noebulletmolds.com/site/product-category/308-311/tl310-225-rn-ce3/

This is the thread where we were discussing .300BLK moulds. http://castboolits.gunloads.com/showthread.php?415931-OK-I-m-confused-Help-straighten-me-out/page2
Post #30 has an interesting linked video that shows it being used in a bunch of guns.

I don't know what you're planning on firing it in, but for semi-auto feeding I wanted something with a small meplat. For hunting a flat meplat would work better as long as it feeds. I didn't want to gamble.

[brown bass hunter]

[QUOTE=BJK;5088882]This mould was suggested to me but I don't have it in hand yet. I ordered mine with the GC option but it's available without. And just because it has the option for a GC that doesn't mean it must use one. Somewhere in that thread far below I link to a chapter of a book where velocities of cast bullets is discussed. I think I should be good to go even supersonic with that bullet and with a GC almost certainly. But I'm new to this and it's just based on what I read and what was suggested to me.
https://noebulletmolds.com/site/product-category/308-311/tl310-225-rn-ce3/

This is the thread where we were discussing .300BLK moulds. http://castboolits.gunloads.com/showthread.php?415931-OK-I-m-confused-Help-straighten-me-out/page2
Post #30 has an interesting linked video that shows it being used in a bunch of guns.


I plan on firing these in a Ruger American Ranch rifle

[brown bass hunter]

Thanks for the help

[Lloyd Smale]

find yourself a rcbs 130 spitzer gas check mold. Best shooting supersonic cast bullet ive found in the 30s.

[waco]

I use this one in my Ruger American Ranch with great results.
https://noebulletmolds.com/site/shop/308-311/311-232-fn-az1/311-232-fn-az1-2-cavity-pb-blkout/

[brown bass hunter]

I ordered this one from NOE today (most are out of stock -if you can believe that) TL310-225-RN-CE3 4 cavity PB

[bigjake]

i purchased this mold from NOE 2-3 yrs ago. i powder coat and gas ck it. it shoots well in the ruger ranch. It feeds and shoots well in a.308 AR

[AndyC]

I ordered this one from NOE today (most are out of stock -if you can believe that) TL310-225-RN-CE3 4 cavity PB

I have that one in 4-cav brass (I'm still in load-development so I have no practical advice) - it feeds in my AR if I set the OAL to 2.090" and gently use a Lee factory crimp die.

https://i.imgur.com/SI5rCNC.jpg