View Full Version : June 2020, Photo Contest, SPECIAL EDITION: Revelation Events
JonB_in_Glencoe
06-03-2020, 12:08 PM
Well, we are in the midst of a virus pandemic and now just recently an incident in my home State has triggered a worldwide civil unrest/rioting. WHAT'S NEXT? I'm not too sharp on my knowledge of the book of Revelation. Maybe some 200 lb hailstones? Maybe the Yellowstone Caldera will let 'er loose in a fantastic Supervolcano eruption? No doubt something else majestic will happen, so I am again, setting aside the normal topic selection process, to open it up to any casting/reloading/shooting things that you are doing during this time of seemingly Tribulation. No older photos rehashed, please. Only new photos of what you are doing during these times.
================================================== =======================
June 2020
Contest topic: Special Edition: Revelation Events
What Biblical plague is next? are you ready, show us how you are ready for it, in the "casting/reloading/shooting"department?
New contest format. New rules. See link for rules.
http://castboolits.gunloads.com/showthread.php?243175-Rules-amended-02-02-2017&p=2797390#post2797390
I am using the individual forum titles as the monthly topics (going from the top down).
OS OK
06-03-2020, 12:51 PM
Singular...no 's' on the end...
https://i.imgur.com/lXJCIcR.jpg
JonB_in_Glencoe
06-05-2020, 12:54 PM
Singular...no 's' on the end...
fixed it.
dragon813gt
06-05-2020, 05:11 PM
https://live.staticflickr.com/4407/36458632982_9a8c2e0128_c.jpg
https://live.staticflickr.com/4407/36489788051_b5ee2f7948_b.jpg
https://live.staticflickr.com/4420/36458633732_86b2436eda_c.jpg
I don’t know if I’m ready for anything. But I’m sort of prepared. No clue what bullets are in the pics. But I do know they are all sized, lubed and ready to load or already loaded. And the ingots may be an old pic but I have enough cores sitting in my garage to make a pile about three times that size. I’d feel a lot better if everything was loaded.
boatswainsmate
06-07-2020, 01:56 PM
https://i.ibb.co/p4FnK9w/DSCN5358.jpg (https://ibb.co/9y5G4Cg)
Hogtamer
06-08-2020, 07:32 PM
263421 263422
Making big holes in little pigs with Lyman 525 gr slugs from 12 gauge
Hogtamer
06-08-2020, 07:33 PM
263423
Adding to the stash
Hogtamer
06-08-2020, 07:35 PM
263424
Perfecting the Lemon Meringue Pie
WinchesterM1
06-09-2020, 04:03 PM
Had another successful D-day party, we fired over 1600 rounds
Does this count?
263438
LtFrankDrebbin
06-14-2020, 03:45 AM
263563
Been putting the 25-20wcf to good use with that RCBS bullet
My master caster can run for hours and days and almost anyone can pull a lever properly with minimum training with a result of thousands and thousands of cast being produced. Best purchase of all of my reloading equipment.
https://i.postimg.cc/FRzFqCbh/20141025_094544.jpg (https://postimg.cc/PpGkv4F7)
JonB_in_Glencoe
06-15-2020, 06:42 PM
I transformed some range scrap today.
263655
Tar Heel
06-28-2020, 04:38 PM
Going Old Testament with the 38WCF.
264159
Theditchman
06-30-2020, 11:57 PM
264293
I've Blued and rusted all my Barrels and completely rebuilt all my rifles just in time for the next gunshow....er...does anyone know when that will be ??...or where ???
AndyC
01-06-2021, 01:24 PM
Question re the Master Casters:
1. Do they use only 2-cavity mold blocks?
2. In a 2-cavity block, where does the pour go, exactly - directly into one cavity and then overflow into the other?
Question re the Master Casters:
1. Do they use only 2-cavity mold blocks?
2. In a 2-cavity block, where does the pour go, exactly - directly into one cavity and then overflow into the other?
Andy. When you setup your mold either single or double you also set up which orifice you use to match the mold cavities. The orifices also come in single or double holes. The pour goes directly into the cavities.
AndyC
03-06-2021, 02:45 PM
Ahhh, I see - thank you for clearing that up. I'm pondering buying one and I couldn't seem to find how they work - thanks!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.