2 dogs
04-08-2020, 05:57 PM
MP Molds 312-85-RF 3 Cavity Brass Cramer Plain Base or Gas Check mold Hollow Point mold on the two cavity blocks or a 6 cavity brass solid PB or GC on the four cavity blocks or an 8 cavity solid PB or GC on the aluminum blocks. This is a new design intended to fill a hole in the MP line-up for 32 caliber handguns and 30 caliber rifles. This is a 640 style nose on this bullet. You have the option of 0.312" and 0.314" as cast sizes and easily sizes smaller. The weight is as shown on the drawing dependent on your alloy of choice.
This bullet fits in all the Ruger Revolvers and Single actions (32 H&R Mag and 327 Federal Mag), 32 ACP semi-auto handguns, all the 32 Short, 32 S&W Long, 32 Colt New Police and older revolvers. It fits most of the 32-20 revolvers as well as 30 Luger, 30 Mauser and 7.62 Tokerev semi-autos.
We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
I am offering these choices: Brass 3 cavity PBHP, Brass 3 cavity GCHP, Brass 6 cavity PB solid, Brass 6 cavity GC solid, Aluminum 8 cavity PB solid and Aluminum 8 cavity GC solid. Your choice of 0.312" or 0.314" diameters.
Pins included are: For the Hollow Point Molds are 1) Large HP pin, 2) Medium Penta HP pin, 3) Cup HP pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are:
3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off.........
I will have to get the other prices.
Sequence of events:
Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address as follows please: imashooter AT gmail DOT com, mold choice, number of cavities, base style (PB or GC), either 0.312" or 0.314" (or both) and number of molds wanted (one to however many).
http://i.imgur.com/soiXVGQ.jpg (https://imgur.com/soiXVGQ)
This bullet fits in all the Ruger Revolvers and Single actions (32 H&R Mag and 327 Federal Mag), 32 ACP semi-auto handguns, all the 32 Short, 32 S&W Long, 32 Colt New Police and older revolvers. It fits most of the 32-20 revolvers as well as 30 Luger, 30 Mauser and 7.62 Tokerev semi-autos.
We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
I am offering these choices: Brass 3 cavity PBHP, Brass 3 cavity GCHP, Brass 6 cavity PB solid, Brass 6 cavity GC solid, Aluminum 8 cavity PB solid and Aluminum 8 cavity GC solid. Your choice of 0.312" or 0.314" diameters.
Pins included are: For the Hollow Point Molds are 1) Large HP pin, 2) Medium Penta HP pin, 3) Cup HP pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are:
3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off.........
I will have to get the other prices.
Sequence of events:
Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address as follows please: imashooter AT gmail DOT com, mold choice, number of cavities, base style (PB or GC), either 0.312" or 0.314" (or both) and number of molds wanted (one to however many).
http://i.imgur.com/soiXVGQ.jpg (https://imgur.com/soiXVGQ)