View Full Version : MP Molds 312-85-RF

2 dogs
04-08-2020, 05:57 PM
MP Molds 312-85-RF 3 Cavity Brass Cramer Plain Base or Gas Check mold Hollow Point mold on the two cavity blocks or a 6 cavity brass solid PB or GC on the four cavity blocks or an 8 cavity solid PB or GC on the aluminum blocks. This is a new design intended to fill a hole in the MP line-up for 32 caliber handguns and 30 caliber rifles. This is a 640 style nose on this bullet. You have the option of 0.312" and 0.314" as cast sizes and easily sizes smaller. The weight is as shown on the drawing dependent on your alloy of choice.

This bullet fits in all the Ruger Revolvers and Single actions (32 H&R Mag and 327 Federal Mag), 32 ACP semi-auto handguns, all the 32 Short, 32 S&W Long, 32 Colt New Police and older revolvers. It fits most of the 32-20 revolvers as well as 30 Luger, 30 Mauser and 7.62 Tokerev semi-autos.

We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.

I am offering these choices: Brass 3 cavity PBHP, Brass 3 cavity GCHP, Brass 6 cavity PB solid, Brass 6 cavity GC solid, Aluminum 8 cavity PB solid and Aluminum 8 cavity GC solid. Your choice of 0.312" or 0.314" diameters.

Pins included are: For the Hollow Point Molds are 1) Large HP pin, 2) Medium Penta HP pin, 3) Cup HP pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.

Prices are:
3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off.........
I will have to get the other prices.

Sequence of events:
Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.

Prices are somewhat variable due to the exchange rate.... be aware of this.

Post your disguised e-mail address as follows please: imashooter AT gmail DOT com, mold choice, number of cavities, base style (PB or GC), either 0.312" or 0.314" (or both) and number of molds wanted (one to however many).

http://i.imgur.com/soiXVGQ.jpg (https://imgur.com/soiXVGQ)

04-16-2020, 12:25 AM
I’ll take a 3 cavity .314 HPGC . Email is thadd3220 at yahoo dot com

04-16-2020, 09:20 AM
I’ll take a 3 cavity .314 HPPB. Email mattlward AT gmail DOT com.

04-27-2020, 09:25 PM
I’ll take a 3 cavity .314 HPPB. Email is eagle-rain AT cox DOT net.

Chris S
04-27-2020, 10:41 PM
I'll take a 3 cavity .314 HPGC. Email is cstephensonrc AT gmail DOT com.

05-02-2020, 07:55 AM
G'Day I'd like a 3 cav .314 hpgc mold please. namovlov at bigpond dot com

05-03-2020, 05:13 PM
If this can be done without lube grooves, I would be in for two 3 cavity .314 HPGC NLG molds. jbpaul AT suddenlink DOT net .


2 dogs
06-01-2020, 04:02 PM
Seven molds.

06-05-2020, 12:28 PM
I would like a 3 cav. PB at .312 kbsten 1 at arvig dot net

06-06-2020, 04:34 AM
Sign me up for an 8 cavity Al PB and a 3 cavity HPPB please.

tony at *my username* com (replace *my username* with my actual username)

Davy Sprocket
06-06-2020, 06:14 AM
I'll take a 3 cav .314 hppb
Fav41 at protonmail dot com

Sent from my SM-G973U using Tapatalk

06-18-2020, 12:52 PM
Since this is a discussion, why not a 4 cavity w/all pins. 4 cavity is a normal mold for Mihec. If that was going to change I would be in for one.

06-25-2020, 05:02 AM
I’ll take a 3 cavity .314 HPPB. Email gspatton AT gttransmissions DOT com.

08-21-2020, 09:02 PM
For thadd3220 @ yahoo please make mine a PB thank you

09-07-2020, 12:30 PM
Is this group buy still open? I would like to get in on a .32 mould.

02-17-2021, 08:29 AM
Perhaps this buy should have a few cartridges listed in the heading. (30 Mauser, 7.62x25, 7,65 french long). I feel like there are a lot of people looking for the perfect 30 mold for all those 30 autoloaders. I'm surprised this isn't hot, as it fills the gap for the one type of autoloading pistol that there hasn't been an MP mold for.

03-21-2021, 11:42 AM
Yes I agree . And also typically when ppl see a sign up list it seems people are a little more interested. The way it appears, is this is still a discussion. Just my .02 cents worth what you paid for . Just hoping to gain some attention for this one

04-25-2021, 09:35 PM
Put me down for an aluminum 8 cavity PB solid in .312. I'll be using this for a 7.62x25 TT-33 Tokarev.

ed at trilogy-health dot com.

06-17-2021, 12:06 AM
Is this discussion still active or has it died?

09-21-2021, 08:20 PM

If this one ever makes it to active I would go for a three cavity .314 PB brass mold. sethdoty 444 at hot mail dot com.

09-21-2021, 10:54 PM
Looks from the drawing that Meplat is a lot smaller than 0.30".... just sayin'....


12-13-2021, 06:16 AM
I've gone a different direction since this seems to have died.

03-17-2022, 04:10 PM
Has this group buy died? Maybe this will revitalize it.

I’d like to have a:
.312 Brass 3 Cav PBHP NLG w/ All pins & handles.