PDA

View Full Version : Mp 311-640 hp design new design



Wasalmonslayer
06-18-2019, 12:38 AM
Hello Gentleman I am helping out with this buy it is being run in conjunction with another board to help boost mold numbers so we can get to the magic 100 pin minimum.

If anyone has any questions I can find out the answer.

It fits the 300 Blackout, 300 Savage and 7.62x39, 7.65 BM and several others if orbited larger besides the normal complement of normal 30 calibers. Offered bullet diameters will be 0.311" and 0.313"..... both will cast out about a half thousandth larger dependent on your alloy of choice.

We will need enough to make Miha's pin requirements. We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.

I am offering these choices: 3 cavity PBHP and 3 cavity GCHP on MiHec's two cavity brass blocks , 6 cavity PB solid and 6 cavity GC solid on MiHec's four cavity brass blocks , 8 cavity PB solid aluminum, 8 cavity GC solid aluminum.
NOTE: THIS BULLET IN 0.311" SIZE WILL NOT FIT WHEN POWDER COATED IN TIGHT THROATED RIFLES. They will fit the larger 0.311" military rifles usually.

Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.

Prices are -

3 Cavity Cramer HP Brass GC or PB - TBD...... it will be less than a 4 cavity but more than a two cavity
6 Cavity Brass solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys
8 cavity aluminum Lee Style solid GC or PB - (80,75 with discount) including shipping, top punch and allen keys



Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.

Prices are somewhat variable due to the exchange rate.... be aware of this.

Post your disguised e-mail address (imashooterATgmailDOTcom), mold choice, base style (PB or GC) and number of molds wanted (one to however many).

Some eye CANDY :)
243747

tradbear55
06-18-2019, 06:19 AM
bluewrench75 AT gmail DOT com
.311- 3 cavity HP w/GC

Wasalmonslayer
06-18-2019, 09:00 AM
Sign up list -

Hp molds
1) bluewrench75 AT gmail DOT com - .311 HP GC
2) denbay58 at twc dot com - .311 HP GC
3) paska_10 at hotmail dot com - .313 HP GC
4) max at yvmarine dot com - .311 HP GC (honcho)
5) twgrubb3 at g mail dot com - .311 HP GC
6) dragon813gt at yahoo dot com - .311 HP GC
7) Lonegun1894 at yahoo dot com - .313 HP GC
8)
9)
10)

Solid Molds -

1) Jay72145 at gmail dot com - .311 6 Cav brass GC
2) dalehi1956ATgmaildotKOM\\ - .313 6 Cav Brass PB
3)
4)
5)

jughead76
06-18-2019, 09:09 PM
Jay72145 at gmail dot com - .311 6 cavity brass solid GC

Wasalmonslayer
06-18-2019, 09:44 PM
Jay72145 at gmail dot com - .311 6 cavity brass solid GC

Got you added sir

castalott
06-18-2019, 11:36 PM
Brass 6 cavity PB solid at .313 please


dalehi1956ATgmaildotKOM\\

P.S. I talked to the designer last night and he says this is a good one if you get the correct diameter for your needs.

Wasalmonslayer
06-19-2019, 08:40 AM
Brass 6 cavity PB solid at .313 please


dalehi1956ATgmaildotKOM\\

P.S. I talked to the designer last night and he says this is a good one if you get the correct diameter for your needs.

You are added

Thank you!

Wasalmonslayer
06-23-2019, 09:42 AM
Bump for the weekend

Cord
06-26-2019, 12:00 PM
Please add me to the list for a:

.311 - 3 cavity GC HP

denbay58 at twc dot com

Thanks!
.

Wasalmonslayer
06-30-2019, 09:39 AM
You are added sir

Thank you!

Wasalmonslayer
07-07-2019, 10:57 PM
Bumpity

Wasalmonslayer
08-11-2019, 09:58 AM
Sun Bump

Teemu
08-11-2019, 11:50 PM
Can i have 3-cavity HP GC .313 diameter. Thanks

paska_10 at hotmail dot com

Wasalmonslayer
08-12-2019, 12:15 AM
Can i have 3-cavity HP GC .313 diameter. Thanks

paska_10 at hotmail dot com

You are added

Thank you!

Wasalmonslayer
09-29-2019, 11:00 AM
Sunday bumpski

Wasalmonslayer
12-10-2019, 12:02 PM
Bumpski

Wasalmonslayer
05-08-2020, 09:04 AM
Bumpity

glockky
05-09-2020, 08:38 PM
3 cavity gas check hollow point .311 twgrubb3 at g mail dot com

Wasalmonslayer
05-11-2020, 01:09 AM
3 cavity gas check hollow point .311” twgrubb3 at g mail dot com

Got you added

Thank you!

cainttype
07-06-2020, 09:02 AM
Would dimensional drawings with measurements be available?
Nose diameter and taper would be appreciated.

Wasalmonslayer
07-09-2020, 12:26 AM
Would dimensional drawings with measurements be available?
Nose diameter and taper would be appreciated.

The design is held very closely and not released by the designer.
Sorry....
This one is not my design or I could give you everything.

Wasalmonslayer
08-05-2020, 08:43 PM
Bumpity

BigHoss74
09-03-2020, 01:01 PM
I will take a .311 6 cavity gas check hollow point
Bri2906 at aol dot com

dragon813gt
10-10-2020, 09:50 AM
Put me down for a 3 cavity .311 GCHP
dragon813gt at yahoo dot com

6622729
10-13-2020, 03:48 PM
I'm in. 3 cavity hollow point, gas check, .311. 6622729 at gmail dot com

Wasalmonslayer
10-24-2020, 01:47 PM
I will take a .311 6 cavity gas check hollow point
Bri2906 at aol dot com

Hello sir No option of 6 cavity hp you can do a 3 cav hp or a six cav solid.

Please inform.

Thanks
WS

Wasalmonslayer
10-24-2020, 01:49 PM
Put me down for a 3 cavity .311 GCHP
dragon813gt at yahoo dot com

You are added

Thanks
WS

Wasalmonslayer
10-24-2020, 01:50 PM
I'm in. 3 cavity hollow point, gas check, .311. 6622729 at gmail dot com

You are added

Thank You
WS

6622729
11-19-2020, 06:01 AM
Please remove me from this list. I ordered a 314-410 mold direct and had it in 5 days. I'm no longer intersted in the 311-640. Thanks.

Wasalmonslayer
12-12-2020, 10:33 AM
Please remove me from this list. I ordered a 314-410 mold direct and had it in 5 days. I'm no longer intersted in the 311-640. Thanks.

Thank you for the heads up

Wasalmonslayer
03-24-2021, 12:22 AM
Bumpski

Lonegun1894
03-25-2021, 10:19 AM
Please put me down for the 3-cavity .313" HP with GC in brass. Lonegun1894 at yahoo dot com. Thanks!

Wasalmonslayer
04-08-2021, 11:02 PM
Please put me down for the 3-cavity .313" HP with GC in brass. Lonegun1894 at yahoo dot com. Thanks!

Got you added

Thanks
WS

Lonegun1894
04-09-2021, 12:02 AM
Thank you very much, WS!