Help identify old shotgun.

[tbx-4]

This old single shot shotgun was sold through Simmons Hardware Co. way back when. I’m trying to determine if it’s a Stevens or what and if it has any collector value. If no collector value then I have a project in mind for it. If I end up using it for my project it would be nice to now how strong the action is.

And yes, it’s a 12 ga.

https://i.imgur.com/BmekHen.jpg
https://i.imgur.com/ieltCce.jpg
https://i.imgur.com/lNTUFCs.jpg
https://i.imgur.com/hDBudd7.jpg

Removable hinge pin
https://i.imgur.com/OCUSYXw.jpg
https://i.imgur.com/DMQHV2J.jpg
https://i.imgur.com/s4upgMp.jpg
https://i.imgur.com/bHgQ8TW.jpg
https://i.imgur.com/V09Bvrm.jpg
https://i.imgur.com/alHxbcv.jpg

[William Yanda]

I suspect the KK stood for Keen Kutter, Simmons house brand, I believe. Hope this helps.

[Texas by God]

The breech face is scary and says "wall hanger" to me. I don't think it's a Stevens.

Sent from my SAMSUNG-SM-G930A using Tapatalk

[GOPHER SLAYER]

I think most of those old inexpensive shotguns had actions made of cast iron so I would second Texas's advice.

[redhawk0]

That's one ugly breech plate...If you're going to make it into a project gun, it better be a very low pressure project. Hang it on a wall over the fireplace...it looks nice...but its in no condition to be fired as is.

redhawk

[skeettx]

https://www.shotgunworld.com/bbs/viewtopic.php?f=5&t=293410

[Mac118]

I have an old H & R 44 shotshell that has a very similar profile. But I imagine there's a number of shotguns from the same era that have a similar profile.

[tbx-4]

Yes, the breach face is an obvious issue. If you look carefully you’ll notice it’s broken out from the inside. Probably from being dry-fired too many times. It’s repairable.

I seen a very similar shotgun identified as a Stevens Model 93. Did the Stevens 93 have a removable hinge pin?

[skeettx]

Do not know
https://www.gunpartscorp.com/gun-manufacturer/savstevspgfld/shotguns-sav/93-sav-2

[KCSO]

Remember that action is cast iron and not strong at all. I would not recommend shooting it with anything but the lightest loads. Not to be made into any kind of modern rifle.

[John Taylor]

If you plan on making it into a rifle, think breach bolt thrust. A 12 gauge has about 5,000 pounds of thrust on the breach which is very close to a 45-70. These old actions will hold with many of the old BP cartridges. The breach face can be repaired and at the same time go with a smaller firing pin diameter. Problem is it may cost more to make the repairs than what it would be worth. Another option is to make it into a muzzle loader using 209 primers.

[tbx-4]

John Taylor,
Thanks for the comment.

Bolt thrust is the critical issue and my calculation came to the same conclusion as yours so I was thinking more in the line of hand gun cartridge carbine.

I have a friend who is a professional TIG welder that can do a good job on breach face for next to nothing and I can do the rest. The value isn’t in making the gun usable again only but the experience gained in the process on my part is worth at least as much.

[John Taylor]

John Taylor,
Thanks for the comment.

Bolt thrust is the critical issue and my calculation came to the same conclusion as yours so I was thinking more in the line of hand gun cartridge carbine.

I have a friend who is a professional TIG welder that can do a good job on breach face for next to nothing and I can do the rest. The value isn’t in making the gun usable again only but the experience gained in the process on my part is worth at least as much.

Welding is not a good idea, it will be as hard as glass. Best to drill it out and make a threaded insert or solder an insert in. A small shoulder will keep it from moving. I have made many of the smaller 410 actions into bunny guns chambered for the 32S&W. Working on one now that is going to use 28 gauge brass for a 58 cal. rifle.

[tbx-4]

Welding is not a good idea, it will be as hard as glass. Best to drill it out and make a threaded insert or solder an insert in.

Roger that!
Thank you again!

[THerbert]

24 gauge would be a better fit for a .58 rifle. 28 gauge would be good for a .54.