Howdy from Denver

[frakncylons]

Denver, NC that is. I don't currently cast, but cast lead bullets are my go to. Thought I would drop by what seemed like the right place and say hello.

I've found lots of good info here so far. I've recently worked up a classic Keith load for a SBH using 2400. Good stuff

[Driver33]

Howdy there is a wealth of info on this site an a lot of members that will be happy to help you with information

[Biggin]

Careful, I'm not sure if this is best described as an addiction or an obsession! LOL!!!

[Bazoo]

Howdy from Kentucky. The wife is from NC. Casting is fun.

[lightman]

Welcome Aboard! Might as well buy yourself a mold and a melting pot!

[jdfoxinc]

Addicted in Denver Co. No 12 step either.

[nvbirdman]

If you stay here long enough you will probably learn that commercial cast boolits are usually undersized and too hard, which contributes to leading.

[Grmps]

loooong time lurker :bigsmyl2:

you might find something usefull here

If you decided to start casting to save money, forget it. You won't, you'll just shoot more.
Casting boolits (lead bullets) properly is a science, once you know the basics, not a hard science.
There is a lot of good information on CB. The Google search (top right of every forum page) is a gateway to all the knowledge on this forum. IF you can’t find your answer there ask the question (Please be as detailed as possible, pictures help http://castboolits.gunloads.com/showthread.php?344661-Capturing-amp-Posting-screen-shots I would be very surprised if there wasn’t someone on this forum that could answer ANY question you might have)
http://www.lasc.us/Fryxell_Book_Contents.htm
1. Boolits need to be cast .0005 to .003 over the slugged diameter of your barrel for accuracy and to avoid leading. If the fit is wrong nothing else will work right.
a. slugging a barrel (it is safer to use a brass rod or a steel rod with a couple of coats of tape to avoid damaging your barrel http://7.62x54r.net/MosinID/MosinSlug.htm
b. chamber casting https://www.brownells.com/guntech/cerrosafe/detail.htm?lid=10614
or pound casting http://castboolits.gunloads.com/showthread.php?356251-Pound-Cast-instructions-(for-rifle-chamber)
2. the right alloy needs to be used for the velocity and purpose of the boolit (don’t fall into the trap of going with to hard an alloy
Economical way to easily test lead hardness
http://castboolits.gunloads.com/showthread.php?355056-Easier-pencil-lead-hardness-testing
https://i.imgur.com/TGUQsIe.jpg
Some alloys harden over time
http://www.lasc.us/Fryxell_Book_Chapter_3_alloySelectionMetallurgy.ht m
different alloy’s different end sizes
https://i.imgur.com/emuBC2T.png?1
Lead alloy calculator
http://castboolits.gunloads.com/attachment.php?attachmentid=45784&d=1341560870
3. velocity the bullet needs to be pushed hard/fast enough to get the proper spin, have the proper velocity to accurately reach the target but not so hard as to be dangerous or strip the lead off in the grooves instead of spinning the boolit..
Powders range from fast to slow, you need to choose the right powder for your application.
Loading manuals list the best powders for certain calibers and boolit weights.
NEVER use any posted noncommercial load data without first checking to see if falls in the safe parameter for your firearm!! There are several firearms out there that can handle much higher pressures than others!!
Link to free online load data
http://castboolits.gunloads.com/showthread.php?337910-CB-load-data-online-sources