Lube

[holsterguy]

Anybody tried the black powder lube that white label currently carries? Thoughts?

[indian joe]

Anybody tried the black powder lube that white label currently carries? Thoughts?

Make yr own - its not that difficult - 50/50 beeswax and neatsfoot oil works for me - getting a boolit that carries enough is more important than the superdooper fantastic recipes I reckon.

[Edward]

Anybody tried the black powder lube that white label currently carries? Thoughts? All their products work well , but I prefer to make my own .Gateo#1 works great not costly and since I roll my own I also enjoy making the lube that gets applied !

[Wayne Smith]

There is a sticky with lube recipies - and BP lube is the easiest to make. I use a modified Emmert's (Lanolin added) for all my BP and pistol shooting.

[country gent]

I use either spg or emmerts improved for my bpcr rifles. These can really test a lube and the lube capacity of a bullet, since barrel lengths run out to 34".
Emmerts Lube
50% Beeswax
40% unsalted Crisco shortening
10% canola or olive oil

Emmerts improved lube
50% beeswax
40% unsalted Crisco shortening
5% canolas or olive oil
5% anahydrous lanolin
I have thought about trying JoJoba oil in place of the canola oil but haven't got around to it yet.

In a double boiler melt beeswax Crisco and oil together when liquid add lanolin if making improved. I have added 2-3 drops of murphies oil soap to help blend the ingrediants together. One all is melted and liquid I "cook" for 5-8 minutes stirring to blend it well. The double boiler is nice as it helps prevent fires and scorching of the lanolin.

One thing to watch is when wiping or cleaning between strings Is how the patch feels going thru the bore. It should feel slippery and slide thru. Fouling should have a wet or greasy look to it, feeling soft and mushy. If the patch starts feeling gritty or crusty the last few inches of the bore, or is dry and crusty hard feeling on the patch you may need more lube. Also watch the lube star at the muzzle It should be wet and greasy looking not dry and crusty.

[rfd]

gato feo is easy to make, cheaper than any store bought lube, and just as effective if not more effective. i use it for bpcr greasers and trad ml patch lubing.

[BRUCE MOULDS]

fouling/lube mix can be soft if there is sufficient humidity in the air.
if it is hot and dry, fouling will be hard and dry until you introduce water, either by blowing or wiping.
straight tallow/wax lubes can look to give dry grey fouling until moistened.
the addition of oil to a lube can help a bit, but even that will not work on its own without moisture.
the reason is that moisture added to a lube/fouling mix makes a soap.
harder lubes will go further up the barrel than softer ones, but be leave a thinner coating.
you have to experiment with lube hardness for weather temp and barrel length, going as soft as possible but not too soft.
different hardness requirements can occurr from summer to winter.
having tried some pretty fancy lubes bought and made, there seems to be little to no avantage to them over the types already mentioned in this thread.
keep safe,
bruce.

[rfd]

... or just use ppb's. :bigsmyl2: :popcorn:

[BRUCE MOULDS]

breech seated.

[Wayne Smith]

... but with BP you would still need a grease cookie, thus lube!

[rfd]

... but with BP you would still need a grease cookie, thus lube!

no grease cookies needed - or wanted.

[BRUCE MOULDS]

depends on what you are doing.
keep safe,
bruce.

[rfd]

depends on what you are doing.
keep safe,
bruce.

yep - hunter's get a grease cookie benefit, but typically not so for targeteers where it can be a negative of sorts.

[BRUCE MOULDS]

rfd,
bear hunters in particular might benefit from a really good grease wad!
other than that the kiss principle remains the dominant factor.
keep safe,
bruce.

[Lead pot]

LUBE....LUBE....I'm a lubeoholic :) to use or not to use that is the question........ :)

I took Brent Danielsons advice while at a match several years ago to eliminate the lube wad. Well I worked with it on and off since but there is always the wandering bullet I think that there is a little gremlin that like to aggravate me that seems to give that bullet a push out of a fine looking group now and then. I think the lube helps seal holding the gas back because I see a lot less wandering bullet holes through the paper.
I us it both ways loading but it takes more then just a wet and a damp patch wiping between shots and this increases as the barrel get hotter in mid summer.
Just a mix of wax and peanut oil works as well as anything for lube. I personally like a mix using Soy wax or Ozokerite wax for the carrier and Vaseline with real coca butter to get the temper I like. I like it very soft almost like warm butter.
I weigh out 280 oz. of lube and melt it in a 12" round cake pan my Wife misplaced some place :) with a inch of water on a hot plate and let it cool. This gives me a uniform 1/8" thick lube slab. Using lube I think it's like Charlie's little friend Linus with his security blankie.
Kurt

[rfd]

NO lube cookie, no thank you, takes up far too much powder room and i want my .45-70's to become virtual .45-90's. [smilie=p:

[Lead pot]

I like my .45-70 girley gun just the way it is :) If I need more powder I use the .45-90 [smilie=p: :D

[rfd]

I like my .45-70 girley gun just the way it is :) If I need more powder I use the .45-90 [smilie=p: :D

ouch, kurt - that smarted. :bigsmyl2:

[Lead pot]

[smilie=l: Cant do nothing else except plow snow when this is coming down. I cant hardly see my 130 yard back yard target. Here I thought all this was over.

217031

[Mark Daiute]

Has anyone used white label's bo lube?