PDA

View Full Version : 30/30 lead


LUCKYDAWG13
03-18-2018, 10:17 AM
I want to cast some boolits for my Win 94 from a Lyman 31141 mold will a mix of W/W and C/O work ok
just looking to Bang Steel at 100 yards or do i need a harder mix
brewer12345
03-18-2018, 10:52 AM
Success probably depends more on proper size and lube than a tweak to your alloy. I drove some 35 rem at 1600+ fps last week with no issues using coww and a couple percent tin. Guessing you will not have problems as long as you get the size of the boolits correct for your bore.
LUCKYDAWG13
03-18-2018, 11:00 AM
I only have a 309 sizer and use Carnauba Red lube so right now the only thing i can change is my lead mix
Dusty Bannister
03-18-2018, 11:19 AM
What is the diameter of the as cast bullets with the present alloy? Have you measured the sized bullet to see if it actually is .309"? Have you considered just quenching the bullets from the mold if you feel a harder bullet is necessary?
LUCKYDAWG13
03-18-2018, 11:33 AM
What is the diameter of the as cast bullets with the present alloy? Have you measured the sized bullet to see if it actually is .309"? Have you considered just quenching the bullets from the mold if you feel a harder bullet is necessary?

I have not cast them yet I have a 50/50 mix in my pot now the last run of boolite that i made up were for my 41 and 44 magnums
that was the mix i used for them so this is what i have ready to go I like to leave my lee pot full and was going to make some
more boolits up for my 44 but now wish to make some boolits up for my 30/30
brewer12345
03-18-2018, 12:57 PM
Are these going to be gas checked? If so, I would let it rip.
HangFireW8
03-18-2018, 03:58 PM
Should work fine. I would add some tin (solder, pewter, whatever) to the mix for fillout. If trying to drive to full speed (2000-2200 fps or so) I would go a little heavier on the WW. Carnauba Red is a quality lube. People have been sizing 30/30 to .001" over since it came out with excellent results.
LUCKYDAWG13
03-18-2018, 04:17 PM
Yes will be G/C I always add about 3% pewter to my mix and no I will not be pushing them fast just looking to hit some steel
at a 100 yards
Thank you all
MaryB
03-18-2018, 09:38 PM
I use Lyman #2 for everything, fit is key, not so much the alloy unless you are really going for speed...
CASTER OF LEAD
03-18-2018, 10:06 PM
I shoot straight WW PC'D for target with great success. As has been said above .FIT is king. I also shoot pan lubed GC boolits with the same results. These are the upper mid range velocities. For banging steel you would be fine with straight WW and maybe some tin for fill out. YMMV - CASTER
Retumbo
03-19-2018, 06:45 AM
Most of my rifle bullets are straight WW + tin. I use 50/50 PC'd for my 45/70.

My 30/30 is gas checked and sized to .309.
c1skout
03-20-2018, 10:32 PM
I use a 50/50 mix of WW and range scrap for both 30-30 and 303 British. No leading in either rifle shooting at speeds up to 2100 fps.
Tom W.
03-21-2018, 01:46 PM
Same here I 've been using COWW w/ just a bit of Nickel Babbitt ( for the tin ) and Carnauba Red w. gas checks for 25 years in my 30/30, and as a fireform load for my 30-06 A.I. Sized to .309
Grmps
03-21-2018, 02:29 PM
Unless the bore of your 30-30 is larger than normal you should be fine.

Have you slugged the bore or done a chamber cast on the gun?
LUCKYDAWG13
03-21-2018, 08:17 PM
Unless the bore of your 30-30 is larger than normal you should be fine.

Have you slugged the bore or done a chamber cast on the gun?

No i have not I made up a 100 or so to try out If things work out I will see how they work out in about 2 weeks