View Full Version : RCBS RS press
abunaitoo
09-04-2017, 10:49 PM
I got an old rusty RCBS RS press yesterday.
Took it apart and it's soaking now.
What is an RS press?????
Looks a little smaller than a RC.
Still looks strong.
BK7saum
09-04-2017, 11:12 PM
Reloader special. I have a RS-5 that came in my first metallic reloading kit. I think it is cast aluminum or an alloy, not steel. Have loaded a lot of ammo on it.
Juan Jose
09-05-2017, 12:22 AM
I've got one of those. A good press for handgun ammo. Get a carbide resizing die if you'll be loading straight walled cases (.38, 9mm, .44, .45 etc...)
abunaitoo
09-05-2017, 01:47 AM
This one is metal.
It's a little rusty.
JBinMN
09-05-2017, 02:03 AM
I have an RS3 that I started using in the early 80s. Mine is steel/iron & still works great.
G'luck with the cleanup! I think you will like it if all goes well for ya getting it cleaned up!
:)
And.... If by chance you end up not liking it, & you decide to part with this one in the future, I would likely be interested in it.
;)
abunaitoo
09-05-2017, 05:11 AM
This must be an old one. It doesn't have the screw in bushing for the different size dies.
Only the 7/8" hole.
KenT7021
09-05-2017, 03:20 PM
I no longer have a Reloader Special but the last one I had was cast iron.As far as know none of the older RS's had a screw in die bushing.They are good presses for normal reloading.
Shawlerbrook
09-05-2017, 04:22 PM
Very good press that can be found at reasonable prices.
dragon813gt
09-05-2017, 04:35 PM
The RCBS parts book should help: http://rcbs.com/RCBS/media/RCBSMedia/PDFs/Parts/Parts_Book.pdf
abunaitoo
09-05-2017, 10:26 PM
Cleaned it up some. Not as bad as i thought it would be.
203494203496203497203498
Artful
09-05-2017, 11:57 PM
My RS-2 is an aluminum frame and no cut for primer feed tube attachment.
It's always good to get a neglected tool up and running again.
GOOD JOB
jimkim
09-06-2017, 11:19 PM
The older ones, like that one and mine, are basically a cast iron RCBS JR-3 with RS written on them, instead of JR.
Sent from my VS880 using Tapatalk
David2011
09-06-2017, 11:38 PM
This one is metal.
It's a little rusty.
Just a side note, pretty sure aluminum is a metal, too.
Big Tom
09-08-2017, 08:03 AM
That one looks identical to my JR model.
dragon813gt
09-08-2017, 08:15 AM
That's because it's an RS 6 model.
marlin39a
09-08-2017, 08:31 AM
My RS is my first press. Stamped 78 on top. It's still on my bench, next to the Redding T7.
abunaitoo
09-14-2017, 03:47 AM
I've always wondered what RS stood for.
Now I know. Reloaders Special.
Landy88
09-19-2017, 02:39 PM
Reloader's Special had a better marketing ring than did Junior Reloader.
Back when I first started loading, by buying one, RCBS packaged these presses and all of the basic essentials, including a coupon for your choice of a die set for common cartridges, in one big box. All of these years later the single thing from that big box that isn't still used and valued as a good to great loading item is RCBS case lube; which is awful, sticky, indelible, messy, and case denting goo.
Wayne Smith
09-20-2017, 11:48 AM
RCBS case lube = STP rebottled. Buy in 55 gal drums, rebottle, and tripple the price. Good business model.
When I ran out I put STP on my lube pad. Same result.
Jack Stanley
09-20-2017, 10:13 PM
RCBS case lube = STP rebottled. Buy in 55 gal drums, rebottle, and tripple the price. Good business model.
When I ran out I put STP on my lube pad. Same result.
A little of that stuff goes a very long way , sort of like using Imperial sizing die wax , just don't use a lot .
Jack
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.