Lyman 310 Swap thread

[slug]

"SWAP ONLY...DO NOT POST PRICES... if you want to post prices and sell items, that must be done in the selling and swapping forum, and obviously follow the rules posted there"

---------

I know that casters are the wierdos of the shooting world, and those of us who like the old 310's are the weirdest of the weird. I'm sure that those of us who lurk in this hand tool section have a few spare 310 bits and need one or two pieces to complete another set. I know that I need a priming chamber and neck expander for .303 British. Can we start a list in this section for our needs and spares so we don't have to look all over creation to find some small piece? And while I'm at it, this is a shameless plea for those .303 bits that I need.


FLASH!
The mod has offered to make this a sticky, for swapping only.
If you want to sell some 310 kit, you have to post it in the Swapping & Selling section.
I'll post some photos of what one of my lil darlings can do, soon.

-----------

[Green Frog]

The concept has been tried in the past, most recently by BrassMagnet. It seems to devolve into confusion pretty quickly as parts from one list get sold, then others get added, and nothing stays current. The PC you request should be easily found as it is the same as that for the 44 Spl/Mag, but I'm less sure about the ME die. Is it a .311" or is it larger?

Froggie

[Char-Gar]

The concept has been tried in the past, most recently by BrassMagnet. It seems to devolve into confusion pretty quickly as parts from one list get sold, then others get added, and nothing stays current. The PC you request should be easily found as it is the same as that for the 44 Spl/Mag, but I'm less sure about the ME die. Is it a .311" or is it larger?

Froggie

Froggie...I have a 303 British boxed set and the muzzle resizer is marked 303 Brit MR and the expander is .311. Lyman has the habit of marking the same sizer with different calibers, so I expect any 30 cal muzzle resizer would work just fine.

[beagle]

Good idea. Problem was nobody updated their lists. I have a bunch of stuff. Odds and ends, bits and pieces and a bunch of complete sets. Looking for a set for the .32 S & W. Have other sets to trade. PM me your needs. May take me a day to dig through my stuff but I'll get back to you./beagle


I know that casters are the wierdos of the shooting world, and those of us who like the old 310's are the weirdest of the weird. I'm sure that those of us who lurk in this hand tool section have a few spare 310 bits and need one or two pieces to complete another set. I know that I need a priming chamber and neck expander for .303 British. Can we start a list in this section for our needs and spares so we don't have to look all over creation to find some small piece? And while I'm at it, this is a shameless plea for those .303 bits that I need.

[largom]

I have a box of Lyman 310 stuff that I am going to dig out and list for sale. Have to find it first!

Larry

[Green Frog]

Good idea. Problem was nobody updated their lists. I have a bunch of stuff. Odds and ends, bits and pieces and a bunch of complete sets. Looking for a set for the .32 S & W. Have other sets to trade. PM me your needs. May take me a day to dig through my stuff but I'll get back to you./beagle

Mr Beagle sir, I have a complete set with nickel handles that I use when at the range as well as a TL Jr set I lucked into at OGCA a few years ago that stays set up on one of my old TL Jr presses. I've been trying to put together a spare set off of flea-Bay and other sources, but I don't know for sure how close I can come to making up a complete set. Do you have any of the parts you need, and are you looking for a nice matched set in a box or would you settle for a made-up set?

Your phriendly 'phibian

[square butte]

Beagle - I think I may have what you are looking for. Have to dig them out. I am still looking for a 25-35 boxed set

[bedbugbilly]

The concept is great . . . the reality is that it's been tried and really gets confusing for the same reasons stated above. Lists didn't get updated, etc. and it soon got so confusing trying to go through all the posts and figuring what was what, I just gave up looking at it. It almost seems like it would be better to use the WTS/WTT or WTB section if you are looking for something specific . . . but not let it get out of hand to "clog" up those sections. I've done that a couple of times in the WTB section for a specific 310 die and have had pretty good luck with the others here who like and use the 310 tools. I've been able to both purchase and trade for what I was looking for.

That said . . . even a post in this section with a question about 310 dies, what you are "project' you are doing, what you've been able to accumulate as far as dies, etc. can often lead to someone reading it who will PM and help you out.

I really wouldn't say that casters are necessarily "weird" . . well some of us are . . . but more like "addicts"! LOL Now those of us that like the old vintage 310/Tru-line stuff . . . that's definitely a "cult"!

[dsh1106]

I really wouldn't say that casters are necessarily "weird" . . Now those of us that like the old vintage 310/Tru-line stuff . . . that's definitely a "cult"!

I thought it was just me ....

I've worked with a few of you in my ventures in the 310 world, all your help and knowledge has been much appreciated.

Scott

[beagle]

Think I might have them. PM me with needs./beagle

[beagle]

No parts on hand so far. Starting out from scratch on the .32 S & W Long. Kinda looking for a set. I have about 15-16 sets for trade and a bunch of orphans./beagle


Mr Beagle sir, I have a complete set with nickel handles that I use when at the range as well as a TL Jr set I lucked into at OGCA a few years ago that stays set up on one of my old TL Jr presses. I've been trying to put together a spare set off of flea-Bay and other sources, but I don't know for sure how close I can come to making up a complete set. Do you have any of the parts you need, and are you looking for a nice matched set in a box or would you settle for a made-up set?

Your phriendly 'phibian

[Texas by God]

To all. I have a Tru line turret press that I want to put to use. It has the 30-06 shell holder in place so I'm looking for .45 ACP dies and possibly 22-250, .300 Sav? Used to have a cigar box of 310 dies but a ghost got them I guess. Best,Thomas.

[slug]

I have a boxed set with steel handles in .222 Rem, that I could put up for adoption.
I need a priming chamber and neck expanding die for .303 British.
A .30/40 Krag or .44 Magnum priming chamber will do as well.
TIA.
slug

[1989toddm]

It has the 30-06 shell holder in place so I'm looking for .45 ACP dies.

So does this mean shell holder for 30-06 and 45acp are the same?
I have 2 die sets for 45acp and 30-06. Would trade for 45-70 or 44 mag dies.


Sent from my iPhone using Tapatalk

[dsh1106]

So does this mean shell holder for 30-06 and 45acp are the same?

Sent from my iPhone using Tapatalk


Yep

Lyman Shell holder #2 (30'06, 270, 308, etc., 45 Auto)

Scott

[Outpost75]

I have some misc. tong tool dies and parts, here is a list, PM me with needs.

I WANT a 455 Webley, or .45 Colt seater die, and a .44-40 seater die

Following items available for sale, trade or offer:

Lyman KF20 body, seater? cal. unk. no plug

7 Priming chamber .303 Brit., .30-40, .455

15 muzzle resizer old style not threaded for a decapper .30-40
15 muzzle resizer with threaded decapper/expander .30-40 Krag
30-40 DA seater, complete
30-06 DA seater, body only no lock ring or plug

123 muzzle resizer .30-06
123 seater die .30-06
123 seater die body .30-'06, no plug or lock ring
2 long decapping die bodies, with rods, pins, unmarked, .30-40 or .30-06?

.311 bullet sizer .30-'06, .30-40, .30-30

.454 muzzle expander .45 Colt

[Texas by God]

1989Toddm are your .45acp dies a 3 die set that will fit 310/Tru-Line loaders? If so are they for sale? I have .44 mag dies but they are RCBS. Best, Thomas.

[1989toddm]

1989Toddm are your .45acp dies a 3 die set that will fit 310/Tru-Line loaders? If so are they for sale? I have .44 mag dies but they are RCBS. Best, Thomas.

They are a 2 die set, not 3. They do fit the Lyman Truline JR press.


Sent from my iPhone using Tapatalk

[vh2q]

I have a bunch of 310 dies complete and incomplete see separate thread under my name. I do have a complete set of 45LC includes the adapter.

[Malamute]

I need to look at the other attempts at this, or search ads for sale or WTB/WTT. I'm a 310 fan, and have ended up with several sets I don't have guns for. One is a complete set with iron handles for 375 H&H. Have a spare complete boxed set with aluminum handles for 30-06 also. Think theres a 270 die set.

Many of the older dies are marked with code numbers. Trying to recall where I saw the code chart.

Here,... http://www.castpics.net/subsite/Lyman310/DieCodeChart.html

[wonderwolf]

I sold off a ton of misc dies about a month ago, wish I saw this page first....would have had trade stock for ages.

Anyways looking for these dies for the tong tools

30-30 seater die and appropriate cartridge guide for the handles, #6 I think.
.44 mag/spl set either the whole set or everything minus the primer seater.

Have a few bits for trade stock (complete 38/357 set and misc) but would mostly be looking to buy.

[largom]

I have 2 small alloy handles, 1 large alloy handle, dies for 308, 30-06, and 45-70. I was going to list these on Ebay but does anyone here have an interest in these?

Larry

[Malamute]

I have 2 small alloy handles, 1 large alloy handle, dies for 308, 30-06, and 45-70. I was going to list these on Ebay but does anyone here have an interest in these?

Larry

I may be interested in 308 dies. Not sure if I already have a set though. I'll try to look tomorrow. May be able to use a small handle.

Not sure if they still sell parts, but Ive bought 310 individual dies and parts direct from Lyman a few years ago. They had different diameter expanders for 38-55 I think, and different seating punches for different bullet types, just like the top punches for sizers. I had several sets of Tru-Line dies that I bought priming dies for and made into 310 dies sets.

[Wayne Smith]

32-20 and 32S&W are very different - 32-20 is a necked cartridge. I have both sets. Can't give you the numbers cause I'm at work, but I can tell you they are not interchangeable.

You can load 32 S&W Long with the 32 S&W dies.

[Green Frog]

Both the 32 S&W and the 32-20 dies for the 310 tool are long discontinued and AFAIK they haven't offered any replacement parts for years. It might be possible to make some substitutions and cobble together a set of either caliber as needed, or you might just check with the 310 Shop about getting a custom set made. It is worth keeping in mind that a 30 carbine set will do fine for 32-20 except for the priming die which is unique to the 32-20 family. I had the devil's own time putting together a set of each for my own use.

Froggie

[Malamute]

Frog, a Lee hand primer tool would get past the priming die problem. Not as nice as a complete set, but makes ammo.

[Green Frog]

Malamute, don't let this get out :roll: but I prefer the Lee hand priming tool to the priming chamber of the 310 set, so I agree completely with your assessment. When I get (or put together) sets of 310 dies for a given caliber though, I like to get the whole set if possible... I'm OCD like that, don'cha know! :coffee:

Froggie

[Wayne Smith]

Froggie, just about two years ago I got a complete set of 32-20 dies in box off eBay. After that I got a set of 32S&W dies the same way. They are available, you just have to be patient and persistent.

[Green Frog]

Wayne,

I found a complete TL Jr set for the 32 S&W at OGCA a few years ago for less than $20, then got a 310 set for even less at another show there a couple of years later. I had owned a complete 310 set for the 32-20 for many years but let myself be talked out of it (thinking I still had the odd parts to assemble another) then lo and behold, I ended up taking a year to gather that "extra" set! I guess if I were using them more often I'd keep up better. :roll:

Froggie

[dsh1106]

I'll get in on this ....

Here's my current want list.


#468 Seating Screw for a Lyman 310 .270 Seating Die

30-30 Bullet Seater (Lyman 310 die)

30-40 MR Die (Lyman 310 die)

#4 shell adapter for the tong tool
#5 shell adapter for the tong tool


I have 310 trading stock PM me.

Scott

[Rimfire]

I have a complete set of 44-40 310 dies I would trade for 32-40,38-40 or 32-20 set.

[Malamute]

I have a complete set of 44-40 310 dies I would trade for 32-40,38-40 or 32-20 set.

I don't have what youre looking for, but may be interested in your die set. I don't own a 44-40 gun, but may one day.

I believe I have a complete set of 270 310 dies.

And a complete handle and die set in the box I think, for 375 H&H. Iron handles.

And a complete 30-06 set with aluminum handles.

Need a set of 348 handles.

[Bent Ramrod]

I have the following:

One #13 muzzle resizer,for .30-30

One 243 Win DA seater

Three #166 seaters for .257 Roberts, two with #450 stems, one with no number stem

One expander 257 stem

One #166 muzzle resizer for .257 Roberts

One #42 muzzle resizer for .38-40

One expander 401 stem

One #118 muzzle resizer for 8mm Mauser

One expander 323 stem

One #118 bullet seater for 8mm Mauser

One #2 priming chamber for .30-06 or 8mm Mauser

One #146 bullet seater die for .300 Savage

Most have lock rings.

Need everything for .44-40 except the bullet seating die: handle adaptor, muzzle resizer, expander and priming chamber. Would prefer to trade.

[Malamute]

OOOh, 25 cal stuff. I just had a 25-06 barrel turned into a 1903 action, I have no 310 stuff for 25 cal. Looks like you have the majority of a set with the Roberts dies.

What would it take to get the 257 Roberts stuff from you? Guessing the length should be close enough to work. The dies would just have to be set out a little more

[SSGOldfart]

Hope you guys can keep this thread running straight, I've got a few dozen sets in the shop,not really sure what I have left,I've traded some here and there,only set I'm really attached to is my 06 set I carried to Vietnam with me.

[SSGOldfart]

I have 2 small alloy handles, 1 large alloy handle, dies for 308, 30-06, and 45-70. I was going to list these on Ebay but does anyone here have an interest in these?

Larry
Larry I'm interested in the 45-70 and 308 sets

[dsh1106]

Need everything for .44-40 except the bullet seating die: handle adaptor, muzzle resizer, expander and priming chamber. Would prefer to trade.

Will a 44 mag expander work for the 44-40? I have a spare expander die with a .429 plug.

Thanks
Scott

[Bent Ramrod]

I really want to get the real set of parts. Have enough makeshifts already. I'd be willing to settle for the "DA" Tru-Line Jr. versions, and shell holder, but that's as far as it goes.

I need to go through my Stuff and see if anything else is incomplete (or surplus), but I'm too busy now. The .44-40 was the chief thing that came to mind.

[Oyeboten]

I could use a few orphan Bullet Seater Stems for loading flat face Wadcutters, if anyone has some they do not need. Or, any Orphan Stems which I cluld re profile for use in seating flat face Wadcutters.



Also, a fast question ~ Were the old "310" Crimp Dies for .38 Special and .32 20 usually a Taper Crimp or a Roll Crimp or could one order them either way?

Mine seem to be taper crimp, and I would prefer to have Roll Crimp if possible.

[wonderwolf]

I could use a few orphan Bullet Seater Stems for loading flat face Wadcutters, if anyone has some they do not need. Or, any Orphan Stems which I cluld re profile for use in seating flat face Wadcutters.




Also, a fast question ~ Were the old "310" Crimp Dies for .38 Special and .32 20 usually a Taper Crimp or a Roll Crimp or could one order them either way?

Mine seem to be taper crimp, and I would prefer to have Roll Crimp if possible.
My 4 and 5 die 38/357 sets are both roll crimp it seems.

[Pavogrande]

32 S&W / long /acp dies, 310 & truline, are often marked "32 pistol"

45acp (310) requires a #7 handle adapter -- a #2 will trap the case when it is expanded in the handles -- #2 is fine in truline jr press

[JonB_in_Glencoe]

Good idea. Problem was nobody updated their lists.
...SNIP


I have a box of Lyman 310 stuff that I am going to dig out and list for sale. Have to find it first! Larry


The concept is great . . . the reality is that it's been tried and really gets confusing for the same reasons stated above. Lists didn't get updated, etc. and it soon got so confusing trying to go through all the posts and figuring what was what
...SNIP

We could probably do this and make it a sticky in this section, for SWAPPING ONLY, but we will not allow any selling, if someone wants to sell outright they'd need to make their post in the selling and swapping section.

Also everyone here that wishes to swap, would need to know that they are on there own, take the necessary precautions to protect your own interests.

I've found it to be the nature of any swapping forum, that some will not update their list and it will get confusing...anyway, I still think this is a good idea.

I sent a PM to slug.
Jon

[JavelinaBlanco]

There is something satisfying about those old 310s...

[wonderwolf]

32 S&W / long /acp dies, 310 & truline, are often marked "32 pistol"

45acp (310) requires a #7 handle adapter -- a #2 will trap the case when it is expanded in the handles -- #2 is fine in truline jr press

I hadn't thought about that, i'll have to look if mine came with a #7 or not. i've yet to load with my 45 ACP set for various reasons. May have to start making adapters on the lathe someday....finding more and more that I could use lol



I have a spare # 10 shell adapter, would like to trade for a #7 if anybody has one.

[Pavogrande]

It is easy enough to open up Handle adapters to a larger size -

I have made them smaller with "press in" reducers --
Make a small counter bore at the top and a small shoulder on the press in bit -

I have made several from scratch on the lathe but the three fine threads (30tpi) have
to be done turning the lathe by hand -- I am just not quick enough to disengage the half nut
anymore --

my ha-penny

[dsh1106]

PM me for my trade list:



SEE POST #30 for my want list.

Thanks
Scott

[wonderwolf]

Ended up getting a complete die set for 30-30 with the shell adapter....should be here mid week.

consequently the dies I have for a partial 30-30 set, everything but the bullet seater and shell adapter. These will be avail for trade when my other set arrives, Still looking for .44 mag dies .

[terryk1379]

Here's a link to the 310 Shop. He's in Denton TX and sells and buys 310 dies, handles, etc. He also manufactures any thing you might want.

http://www.cnyauctions.com/the310shop.htm

[1989toddm]

Here's a link to the 310 Shop. He's in Denton TX and sells and buys 310 dies, handles, etc. He also manufactures any thing you might want.

http://www.cnyauctions.com/the310shop.htm

I was not aware that he made dies. Is that what you mean?

[Green Frog]

He was (at one time) offering custom-made dies in calibers no longer made or commonly available. I haven't checked with him lately, but that was the situation when last I checked.

Froggie

[wonderwolf]

He was (at one time) offering custom-made dies in calibers no longer made or commonly available. I haven't checked with him lately, but that was the situation when last I checked.

Froggie

His website hasn't changed in a while at least thats what it looks like to me so I'm not sure how active he is anymore. Somebody though is selling new mfg lock rings on ebay from time to time.

[Outpost75]

Will a 44 mag expander work for the 44-40? I have a spare expander die with a .429 plug.
Thanks Scott

The .429 will work for .44-40s of recent production which were assembled using .44 Magnum bore and groove spec barrels,
which require larger bullets. Will not work for older guns requiring .428 and smaller boolits.

[tmc-okc]

The 310 Shop is still in full swing.
Rick Morrill - A really nice guy


The 310 Shop
4237 Boxwood drive
Denton Texas, 76208

940-271-1222

He is not a computer guru and knows his website leaves a lot to be desired. He doesn't like communication via email either. But if you call him he will answer if he is in the shop.

I purchased a NIB 4 die set for my 218 BEE rifle just a couple months ago. This guy is just chock full of knowledge.

As him if he has any Buffalo burger left - LOL

Ron H

[dsh1106]

Updated Swap List - POST #30

[BrassMagnet]

Malamute, don't let this get out :roll: but I prefer the Lee hand priming tool to the priming chamber of the 310 set, so I agree completely with your assessment. When I get (or put together) sets of 310 dies for a given caliber though, I like to get the whole set if possible... I'm OCD like that, don'cha know! :coffee:

Froggie


Many of the steel 310 tong tools are badly worn on the bump. Brass rubbing on steel should not wear the steel. I suspect the priming chamber (or boolit sizing die!) is at fault for the wear due to steel on steel.
I have read the alloy handles are superior to the steel handles because the bump is spring steel and replaceable. The "L" and "S" steel handles have the removable spring steel piece, too. I prefer steel. I quickly broke the first alloy set of handles.

I like the idea of priming with other tools when possible, too!

I'm going to try to put up my own chart as soon as I get it made up, proofed, and validated.

Here is a link to an article that references 310 tools for reloading.

http://www.endtimesreport.com/survival_reloading.html

[Green Frog]

Hey B-Mag! Good to have you join in the discussion... I haven't noticed you posting much lately. Once I decided I "needed" the steel handles I was able to get most of the caliber-specific ones I needed without much drama. Getting the steel L and S sets to use for all the other calibers to strike my fancy was a bit more challenging and required trolling gun shows for a couple of years. Keep in mind that all of this occurred at least 20+ years ago and not as many folks were beating the bushes to get them. Thanks for the explanation about the spring steel bump... I hadn't really thought about the wear aspect of it.

Regards,
Froggie

[1989toddm]

I got a question for the group, can a pair of caliber specific 310 handles that has the mold on the end be used to load a different similar sized caliber than that which is stamped on the tool?


Sent from my iPhone using Tapatalk

[dsh1106]

I got a question for the group, can a pair of caliber specific 310 handles that has the mold on the end be used to load a different similar sized caliber than that which is stamped on the tool?


Sent from my iPhone using Tapatalk

If you're talking about something like a 300 savage, 30-06, 308, 30/40 etc or 38/357, 9MM, 38 super. If the weights are comparable, it's possible sizing would be the key.


Scott

[1989toddm]

Was thinking of loading 22 hornet in a set marked 25-20. From what your saying, it sounds like it needs to be the same size neck.


Sent from my iPhone using Tapatalk

[dsh1106]

Was thinking of loading 22 hornet in a set marked 25-20. From what your saying, it sounds like it needs to be the same size neck.


Sent from my iPhone using Tapatalk

Oops, I took it your question was about the bullet that was cast in the mold.


I'm not sure about the 22 hornet, I do know that you can use a set of 30-06 marked handles to load 308, 270, 243 etc, basically any cartridge that takes the #2 shell adapter. As with most things like this, I'm sure there are exceptions. I'll take a look at the 22 hornet and see what I come up with.

Edit - 22 hornet and the K hornet are the only two cases that use the #4 adapter. I guess from this point you'll have measure the the diameter and see if there's something close.


Scott

[1989toddm]

Oops, I took it your question was about the bullet that was cast in the mold.


I'm not sure about the 22 hornet, I do know that you can use a set of 30-06 marked handles to load 308, 270, 243 etc, basically any cartridge that takes the #2 shell adapter. As with most things like this, I'm sure there are exceptions. I'll take a look at the 22 hornet and see what I come up with.

Edit - 22 hornet and the K hornet are the only two cases that use the #4 adapter. I guess from this point you'll have measure the the diameter and see if there's something close.


Scott

So then, the shell adapter is not removable on those caliber specific handles?

[dsh1106]

Correct, the caliber specific handles don't have a screw in adapter, the handles have the casing diameter machined in the handles.

[1989toddm]

Correct, the caliber specific handles don't have a screw in adapter, the handles have the casing diameter machined in the handles.

Thank you! Now back to our regularly scheduled programming.[emoji848]


Sent from my iPhone using Tapatalk

[Green Frog]

I have found it satisfactory to use a slightly smaller diameter case body with the 310 tool... it works because the case body is aligned by the die. Just a FYI!

Froggie

[Frogfeatures]

Hi guys
keen on swopping a 30.06 die set for one in 222 / 223
PM me, thanks.
181187

[BrassMagnet]

181490

This is a photo of one page of a spreadsheet of 310 tools.
If you PM me your email address and a request for the 310 spreadsheet in the subject line, I will email it to you.

Now some quick explanations.

From the newer style of handles there are five kinds.
Small Alloy
Large Alloy
Small Steel
Large Steel
Caliber Specific Steel
Large and Small, whether alloy or steel use the screw-in adapters. Caliber Specific handles are drilled to fit the case. A Caliber Specific handle will fit that caliber, but not always others that should be the same adapter number.
Example 1: 30-06, 270, 7MM, 8MM will fit any rifle cartridge which uses the same shell holder as a 30-06.
Example 2: 222 or 38 handles are not necessarily interchangeable. 38/357 cases are not identical dimensions to the 222/223 case dimensions. A #1 Adapter will fit both, but I have caliber specific handles which will not!

So my spreadsheet allows me to mark it as any of the five types with the two columns available.

Normally, cases are expanded larger for cast boolits than for jacketed bullets. Different seating punches are listed for cast or jacketed. Normal sets only come with one expander and one seater. Lyman was not consistent with which seating punch was used. The seating punch number is the same as the seating punch for a Lyman Sizer/Lubricator. They did not make them all, but they did make many more than they listed on their chart!

There were more die sets made than were listed on the Lyman chart. I validated the data I entered from the chart was correct per the chart and then I corrected gross errors. Then I added data from sets I have which are not on my chart.

Column 2 is TruLine Jr/Lyman All American Type J shell holder numbers which are the same as Lyman numbers.

Blank spaces are data not available.

Some questions have been asked about the column titles

Here are answers:

AD = Adapter

Handle type:
S = Steel
A = Alloy
SL = Steel Large
SS = Steel Small

See posts 68, 70, and 72.

[Malamute]

Im not positive, but I suspect a large part of the problem with the steel handle wearing at the bump may be carbon from decapping, not just the brass rubbing and wearing. After breaking several decapping pins, I gave up on them and use the Lee decapping punch set for my 310 use, so am not experiencing the carbon on the bump. The steel (iron?) handles probably aren't as hard as the removable spring steel plate that the alloy handles have though. I haven't had dies stick out and rub.


So wait, are there any steel handles that use removable shell adapters? I thought they were all caliber specific (or within a general shell size range as was discussed). If there are steel handles with removable shell adapters, do they have adjustable shell hooks like the alloy handles?

Ive often wondered if it were possible to alter iron handles for the shell adapters. A tap is probably required, inside turning of the treads on something that small may be tricky. If anyone did that work, Id send a couple handles to be machined.

The guy that had the 310 shop before the current guy (was in WA state I think, then Tombstone Az I believe) said he had scads of iron 30-06 handles, I think he said nearly a 55 gal drum of them, (not sure if he was totally serious, but he said he was). I think he said he'd trade them in multiples to get odd sizes that he could make complete sets from. Not sure if current guy trades them that way. I didn't buy anything from him after prices doubled when be bought the business.

[BrassMagnet]

So wait, are there any steel handles that use removable shell adapters? I thought they were all caliber specific (or within a general shell size range as was discussed). If there are steel handles with removable shell adapters, do they have adjustable shell hooks like the alloy handles?


The Large and Small Steel handles do. They are identical to the alloy handles except they are made from steel. I can post photos, if needed.

[Malamute]

So wait, are there any steel handles that use removable shell adapters? I thought they were all caliber specific (or within a general shell size range as was discussed). If there are steel handles with removable shell adapters, do they have adjustable shell hooks like the alloy handles?


The Large and Small Steel handles do. They are identical to the alloy handles except they are made from steel. I can post photos, if needed.

I would like to see pics if its not too much trouble, not that I don't believe you, just interested, I didn't know they made them so. I may like to trade into some.

Thanks!

[BrassMagnet]

181529
Large, Steel and Alloy

181530
Large Steel color and Marking "L"

181531
Small, Steel and Alloy

181532
Small Steel color and Marking "S"

181533
Caliber Specific Steel

181534
Caliber Specific Steel color and Markings "222 REM" &="218 BEE"

181535
Insides of all six handles shown above

181536
Insides of two Large handles shown above


181537
Insides of two Small handles shown above

181538
Insides of two Caliber Specific handles shown above, 222 REM & 218 Bee

[Malamute]

Excellent pictures, thank you!

[BrassMagnet]

Excellent pictures, thank you!

Now this part is merely hearsay!

I don't know, but I have been told the steel "L" and "S" handles were only made for a year before they went to alloy handles.

Now this part I do know. I break pruning shears. I broke my first alloy handle the first day I used it. Rather quickly, too!

When I learned about the steel handles I started searching for them. When I heard about the "L" and "S" handles I really got serious about searching for them.
"L" handles are expensive, but come up on FleaBay fairly often. If they are listed as Large Steel they get expensive. If they are in a set with dies, they cost less. If you can only identify them by the color and spring steel bump piece, then they become rather affordable.
I used to believe the "S" handles were merely a myth, then a friend sent me a link to a set on FleaBay. Then he sent me a link to another set. I now have both sets.

[Green Frog]

Brass Magnet, oddly enough, when I decided I "needed" a set of steel handles, I was so pleased to find the first set I didn't even notice that they were "S" handles until I got home... it was the better part of a year before I got the "L" set which I am really more likely to use. Fortunately I have been able to accumulate the caliber specific handles for most of the calibers (rifle and pistol) I load the most frequently (sometimes using "families" of cartridges based on base or case body diameter.) When I load an oddball cartridge, however, the large and small interchangeable set are right there to be used. :D

Froggie

[BrassMagnet]

Some questions have been asked about the column titles in the spreadsheet.

Here are answers:

AD = Adapter

Handle type:
S = Steel
A = Alloy
SL = Steel Large
SS = Steel Small

See posts 68, 70, and 72.

[ulav8r]

A good spreadsheet generously shared.

BrassMagnet, Thanks for the spreadsheet.

[1989toddm]

A good spreadsheet generously shared.

BrassMagnet, Thanks for the spreadsheet.

+1!


Sent from my iPhone using Tapatalk

[JonB_in_Glencoe]

We could probably do this and make it a sticky in this section, for SWAPPING ONLY, but we will not allow any selling, if someone wants to sell outright they'd need to make their post in the selling and swapping section.

Also everyone here that wishes to swap, would need to know that they are on there own, take the necessary precautions to protect your own interests.

I've found it to be the nature of any swapping forum, that some will not update their list and it will get confusing...anyway, I still think this is a good idea.

Jon

I have edited the title and the OP and made it a sticky.
Good Luck.

[Green Frog]

Public thanks go out to Brass Magnet for generously sharing his work on this spreadsheet. It will be a most useful addition to my references.

BTW, Brass Magnet, I got an e-mail that you had tried to PM me bot my inbox was full. I fixed that now.

Froggie

PS The staff at Cast Pix, at my request, has fixed the incomplete posting I had submitted years ago to their predecessor. It shows the die codes arranged numerically so you can find out readily what that unknown die is used for. Kudos to the Cast Pix administrator who did this for us... not too many folks have access to the old issue of The Single Shot Rifle Journal, so it's nice to make it more widely available.

[dsh1106]

Updated Swap List - POST #30

[nitro-express]

I'd like to have a #4 PC, for the 22 Hornet.

Also on my ISO list: a #2 adapter to complete a mint 243 Win 310 die set I'd like to sell.

Up for trade are the following:

- 310 dies for 220 Swift; #169 DA c/w 367 seating stem, #169 DA c/w 367 seating stem, KF-20 EC c/w 223 expanding button.

- 310 dies for 257 Roberts; #166 MR, EC c/w 257 expanding plug.

- 310 dies for 44 Spl; DA c/w 421 seating stem, EC c/w 429 expanding button.

- DA (#150) 44 Russian/Special c/w 421 bullet seating screw.

I bought a pail of dies at a gunshow, if you need anything ask. I have some real odd ducks, like a 7.62x54R PC.

I'm from Canada, USPS works, just costs a bit more.

[BrassMagnet]

I have a #3 MR die.

Muzzle resizer for 22 WCF.

22 WCF is not 22 Hornet or 225 Win. It is 22 WCF.

See this thread:

http://www.assra.com/cgi-bin/yabb/YaBB.pl?num=1221705914

[BrassMagnet]

I have PC#17

Priming Chamber #17 for 33 Winchester.

[BrassMagnet]

I have Priming Chambers #21, #25, & #27

#25 is 41 Long

What is #21 for?

What is #27 for?

[SgtDog0311]

I inventoried a box of items I had and put the best description from the markings. Be glad to provide pictures or further description if you have any questions. I’m looking for dies for 40-63 (405 doner cases. I already have the priming die); 40-65; 38-50 (30-40 Kraig and RMC cases); 35-40 (38-55 Cases); or 38-55. Also interested in tong tools or case inserts for 45-70 or 38-55.

310 243 4 dies
*243-2440Da
*Deprime #2
*Expander
*Sizer 243 WIN-MR
310 (Box Marked 222)
*Seater (222) stem marked 45C
*Decapper (no marking)
310 (sacked marked 30-06 Short
*Sizer (marked 123)
*Priming die bullet seater stem?
*Looks like Expander plug
310 Two Dies
*Stem (marked 329)
*Sizer
*Decapping die
310 Two dies and Seating stem
*expander (marked 311)
*Expander (Marked 224)
*Seater (marked 277)
310 Expander Plugs
*marked 285
*marked 280
310 Shell Inserts
*marked #1
*marked #2 (2)
310 Sizer Dies
*Marked 222
*Marked 116
310 Priming stems
*Spring return (2)
Two dies
*One looks to be a sizer (marked 121)
*Priming die (marked #6)

[BrassMagnet]

I have Priming Chambers #21, #25, & #27

#25 is 41 Long

What is #21 for?

What is #27 for?

Priming chamber #25 has been traded. I still don't know what #21 and #27 are used for.

[BrassMagnet]

I have PC#17

Priming Chamber #17 for 33 Winchester.

Priming chamber #17 for 33 Winchester has been traded.

[bbogue1]

To all. I have a Tru line turret press that I want to put to use. It has the 30-06 shell holder in place so I'm looking for .45 ACP dies and possibly 22-250, .300 Sav? Used to have a cigar box of 310 dies but a ghost got them I guess. Best,Thomas.


I too am a fan of the tru Line Jr. according to my charts the 45 ACP, the 30-06-the 22-250 and the 300 Savage all take the #2 shell holder.

[rbuck351]

I just picked up 2 Tru Line JR turret presses cheap and found the 310 dies to be a bit pricey. There is a fellow on evil bay tha makes a new turret for the JR that uses normal loading dies. I just bought one for $40. It fit well and works well and now I can use my existing dies and I have the adapter to use std shell holders as well. The press doesn't have a lot of leverage so I'll probably set it up for 32 S&W long and a couple of other easy to size cases.

[BrassMagnet]

I just picked up 2 Tru Line JR turret presses cheap and found the 310 dies to be a bit pricey. There is a fellow on evil bay tha makes a new turret for the JR that uses normal loading dies. I just bought one for $40. It fit well and works well and now I can use my existing dies and I have the adapter to use std shell holders as well. The press doesn't have a lot of leverage so I'll probably set it up for 32 S&W long and a couple of other easy to size cases.

Great for neck sizing and bullet seating!

[Green Frog]

I just picked up 2 Tru Line JR turret presses cheap and found the 310 dies to be a bit pricey. There is a fellow on evil bay tha makes a new turret for the JR that uses normal loading dies. I just bought one for $40. It fit well and works well and now I can use my existing dies and I have the adapter to use std shell holders as well. The press doesn't have a lot of leverage so I'll probably set it up for 32 S&W long and a couple of other easy to size cases.

One of my TL Jr presses stays set up more-or-less permanently for the 32 S&W Long. It seems to be the perfect size for that cartridge. I have to admit though that I often batch process the brass by doing decap and full length sizing with a TC die in a big single stage press.

Froggie

[Malamute]

I inventoried a box of items I had and put the best description from the markings. Be glad to provide pictures or further description if you have any questions. I’m looking for dies for 40-63 (405 doner cases. I already have the priming die); 40-65; 38-50 (30-40 Kraig and RMC cases); 35-40 (38-55 Cases); or 38-55. Also interested in tong tools or case inserts for 45-70 or 38-55.

310 243 4 dies <--- Im interested in this group if we can come to a mutually acceptable agreement
*243-2440Da
*Deprime #2
*Expander
*Sizer 243 WIN-MR

310 (Box Marked 222)
*Seater (222) stem marked 45C
*Decapper (no marking)
310 (sacked marked 30-06 Short
*Sizer (marked 123) <---123 is the code for 30-06
*Priming die bullet seater stem?
*Looks like Expander plug
310 Two Dies
*Stem (marked 329) <---- If its a plain expander stem, that should be the diameter

*Sizer
*Decapping die
310 Two dies and Seating stem
*expander (marked 311) <----
*Expander (Marked 224) <----these should be diameters
*Seater (marked 277) <--- not in my chart, it may equal the last 3 digits of a mould number

310 Expander Plugs
*marked 285 <---should be diameters
*marked 280
310 Shell Inserts
*marked #1 <---This is 30-30 class shells. I could use this

*marked #2 (2) <---30-06 class shells, any similar diameter also, like 250 sav

310 Sizer Dies
*Marked 222 <---for 222, can probably work with any similar sized 22 centerfire

*Marked 116 <----7mm, meaning 7mm mauser
310 Priming stems
*Spring return (2)
Two dies
*One looks to be a sizer (marked 121) <---shows as 405 Win if its a sizing chamber

*Priming die (marked #6) <---30-30 I'm interested if we could come to an agreement



Posted comments in the quote above with arrows <--- Info is from my copy of the Lyman Ideal Handbook No 39, copyright 1953

I would be interested in a set for 25-06 (257 would probably work also), even if pieced together. I have spare priming chambers and expander chambers that I can complete it with, the other parts are what I need. Could make do with just the expander stem also along with the muzzle resizer and DA(seater/crimp die).

I have a 30 cal magnum (probably 300 H&H, but may work with Win Mag) muzzle rezizer and DA die Id trade.

Have two pieces of 303 Brit dies. Will check further to ID which parts.

Need a handle for 348.

Interested in 44-40 set

Have a complete steel handle set for 375 H&H Id trade for anything useful to me.

[Wayne Smith]

Well, since I now have the shell holder, I guess I'm on the lookout for a set of 38S&W dies! What a way to begin - start with a shell holder purchased by accident because of my dyslexia! I'll have to find a gun, too.

[BrassMagnet]

Well, since I now have the shell holder, I guess I'm on the lookout for a set of 38S&W dies! What a way to begin - start with a shell holder purchased by accident because of my dyslexia! I'll have to find a gun, too.

It has just started. Mould. Sizing die.
Just sent it my way. All I need is a pistol.

[Green Frog]

It has just started. Mould. Sizing die.
Just sent it my way. All I need is a pistol.

May I suggest a S&W Terrier? (It's cute as a speckled pup!)

Froggie

[Wayne Smith]

Cute, yes. However, LOML convinced me I can only spend money once - and I still have to pay for the flintlock. Expecting an e-mail any day.

[JoseBob]

I have a complete .45 ACP Lyman 310 tool new. I would like to trade it for .22 Hornet 310 dies... I have an extra small handle.
Please let me know... Thanks... Bobby...

[BrassMagnet]

I have a complete .45 ACP Lyman 310 tool new. I would like to trade it for .22 Hornet 310 dies... I have an extra small handle.
Please let me know... Thanks... Bobby...

Can do!

[wonderwolf]

Anybody have 303 savage dies or .44spl/mag dies collecting dust?

[JoseBob]

Deal made... Thanks.... Bobby

[Rimfire]

I have a set of 44-40 (complete) will trade for a good set of 223 Remington regular press dies. The 44-40 dies are in excellent shape and are in the original orange plastic box.

[Green Frog]

I have a set of 44-40 (complete) will trade for a good set of 223 Remington regular press dies. The 44-40 dies are in excellent shape and are in the original orange plastic box.

I can do that... contact me via PM to close the deal.

Froggie

[NoZombies]

Would anyone have interest in a complete steel handled set for .38/.357? The only thing they don't have is the original box. I'd love to trade straight up for a steel handled set for 30-06 (a cobbled set would be fine) but might be talked into other caliber 310 dies, 38-55 might be of interest, possibly even 30-30.

[dsh1106]

Would anyone have interest in a complete steel handled set for .38/.357? The only thing they don't have is the original box. I'd love to trade straight up for a steel handled set for 30-06 (a cobbled set would be fine) but might be talked into other caliber 310 dies, 38-55 might be of interest, possibly even 30-30.

I have a handful of 310/ TL Jr die sets that I'd be willing to trade for your 38/357 set.

Scott

[bbogue1]

This may be in the wrong place, if so, please move this post to the right location.
In the original 30-06 die set what was included? I look at my 310 chart and it is confusing; such as were there 3 different length seating dies? I have a 308 die which I believe is a 30-06 neck expander with stem and I have a long 413 die which I believe is a medium length case sizing die. Then I have two stems and a die body. The die body is marked 123 and is about half the length of the longer 413 die. The stems look to be seating stems but one is thicker than the other. Both are so short they would only work in the shorter 123 die body, but, there are no threads in the die body. What do I have and what do I need to complete a 30-06 die set? At some point these dies as a set will be swapped.

208379

208380

[trooperdan]

Are these Tru Line Jr or 310 dies? Do you have a decapping stem in either die, doesn't look like it. The 123 die is the muzzle reducer and the longest die should have the bullet seating stem in it. You need the decapper die and an expanding chamber with .308 stem.

[woody1]

Left to right, here's what I see:
1 - expanding chamber with .308" muzzle expanding plug
2 - bullet seating die with 413 seating screw (for cast bullets) double adjustable chamber with seat screw (could also be marked 123)
3 - 123 Muzzle resizer (for 30-06)

below looks like another seating stem and a ?

[trooperdan]

SWAP ITEMS:
.308 CMR, missing decapping stem, skinny stem this is stamped .30-308 but I think it is .308
.243 decapper- neck sizer
.280 expander plug
.277 expander plug
.30-30 DA seater
.30 Carbine CMR


EXPANDER PLUGS
.223
.225
.255
.263
.283
.308
.311
.356
.357
.429
.452


I need:
.244 decapper-resizer
9 m/m decapper
.243 decapper-resizer
.30 Carbine decapper-resizer
8x57 decapper-resizer assy
.357 MR, #3 primer,

[bbogue1]

It never ceases to amaze me the depth of knowledge the wonderfully generous members of this forum are. I believe these are 310 dies, though, I load 9mm and 38 Special on a original True Line Jr. and could be Tru Line. I am open to swap any or all of these. I just hate to see such tools go unused.

[BrassMagnet]

It never ceases to amaze me the depth of knowledge the wonderfully generous members of this forum are. I believe these are 310 dies, though, I load 9mm and 38 Special on a original True Line Jr. and could be Tru Line. I am open to swap any or all of these. I just hate to see such tools go unused.

They are 310 dies. I would trade for the Truline Jr and the 310 dies mounted on it!

[bbogue1]

They are 310 dies. I would trade for the Truline Jr and the 310 dies mounted on it!

Good catch BrassMagnet, my eyes POPED open when I read that.

OHHHH I am in trouble, I meant I would trade the dies, etc. only the ones that I am asking what they are (the ones in the photos). I am not interesting in trading the True Line Jr setup UNLESS the trade equals what I have so I could continue loading and here's the important part..... the replacements make me drool and pant and make me stay awake at night ( I did that when I was expecting the True Line Jr''s so as you can see, they have a special place in my life).

[trooperdan]

Looks like no one bothers to read this part of the forum.

[bullet maker 57]

I would like to trade these sets. One is a complete set for 22 Jet. the second is a complete set for .244/ 6mm.

There are some loose dies: seating #143, neck sizer 6mm, expander 6mm, and a 7/8x 310 die thread bushing.
Hopefully somebody can use these dies.
209549209550

[trooperdan]

What are you looking for in trade? I don't need the 6 mm but am interested in all others

[bullet maker 57]

The 311 expander, #2 priming chamber, and the unmarked decapper are spoken for.
Make me a fair offer. You never know.

[mwells72774]

Have a 22 hornet set I’d like to swap for a 38/357 set

[BrassMagnet]

Have a 22 hornet set I’d like to swap for a 38/357 set

If you don't mind a "set" assembled from odd dies we can trade.

[mwells72774]

Dug through and found my 30-40 krag 310 set looking to trade for tru-line sets, something like 44 mag, 30 carbine, or even a converted die plate

[BrassMagnet]

Dug through and found my 30-40 krag 310 set looking to trade for tru-line sets, something like 44 mag, 30 carbine, or even a converted die plate

I do need a 30-40 Krag 310 set. Shall I start scouting out my TrueLine sets for trade bait?

[firebyprolong]

I picked up a set of 44-40 marked steel handles in a trade a while back that I'd like to trade for a newer set of universal large handles with some shell adapters if anyone is interested. Thanks

[wonderwolf]

I picked up a set of 44-40 marked steel handles in a trade a while back that I'd like to trade for a newer set of universal large handles with some shell adapters if anyone is interested. Thanks

If you don't get a trade I have a couple sets of large universal I would sell. Might even have a shell adpater you're looking for as well.

[wonderwolf]

Does anybody know if a .222 priming die will work to prime 9mm? I know they are different #'s in the chart but I'm really wanting to prime off press for 9mm since I currently share the reloading room with SWMBO 's office and she has been crazy busy lately.

[dsh1106]

I never tried it ..
222 is #26
9mm is #12

I'll check it out tomorrow after work.

[square butte]

I just tried a 9mm case in my #26 - It's close, but just won't quite fit all the way

[trooperdan]

9 mm fits a # 26 priming chamber just fine. Put some pressure on it and it didn't jump out, didn't actually prime one but I'll bet it works.

[wonderwolf]

If anybody has a #26 priming chamber they can let go of let me know.

[trooperdan]

Looks like it might be the luck of the draw, depending on case brand and individual tolerances. I might have a spare 26 or 12, let you know in the AM.

[wonderwolf]

Looks like it might be the luck of the draw, depending on case brand and individual tolerances. I might have a spare 26 or 12, let you know in the AM.

Awesome

[BrassMagnet]

9MM brass case rims are all over the map on size. Too many makers, too many differing tolerances!

[dsh1106]

I believe I have an extra #12 priming chamber, PM me if trooperdan can't help.

Scott

[NoZombies]

Alright, I'm gonna try this again...

Things I have for trade:

1. Traded

2. Complete caliber specific steel handle set and dies for .38/.357 in pretty nice shape for the age. (this is the steel handles and a 5 die set)
3. Complete 5 die set and shell collar for .22 Hornet
4. traded

And for the Trueline JR:
5.True Line jr set for .270, possibly never used from the 60's Includes shell holder and priming punch. All in the Black orange and white boxes (4 little boxes inside of the 'set' box)
6.True line Jr 2 die set (just the dies) for 30/30

I'm interested in trades as follows:

Die sets I'm looking for (either true-line or preferably 310):
9.3x57R
38-55
25-20 Single Shot (not WCF)
Other unusual sets

[Gtrubicon]

Pm sent on item #1

[BrassMagnet]

Lotsa trade bait for 310 & TrueLine Jr. Includes L Steel handle and Carcano dies.

[kaiser]

I have a .44 Special 310 sizer/deprimer die (deprimer pin broken) and a .38 spl./.357 seating die for trade. I need a .38/.357 priming die and #1 shell holder. Thanks, Kaiser

[Green Frog]

Lotsa trade bait for 310 & TrueLine Jr. Includes L Steel handle and Carcano dies.

You wouldn't happen to have a set of 44-40 dies would you, Brass? I'm also interested in that set of L steel handles.

Froggie

[dsh1106]

Lotsa trade bait for 310 & TrueLine Jr. Includes L Steel handle and Carcano dies.


Did I find you to many Large handles?

[BrassMagnet]

Did I find you to many Large handles?

No. Just not enough “S” Steel!

[dsh1106]

No. Just not enough “S” Steel!

I'll keep an eye out for more of the "S" handles ..

[sharps4590]

Not long ago I bought a large 310 tool and it came with an assortment of dies, what I think is one set.....maybe. Even the box is in remarkable condition. I'll just list what I have and hopefully someone can tell me as I can't seem to find any chart of what the various numbers mean. There is a direction sheet came with the tool but that's all.

One die is marked 223 REM FL which I assume to be the sizing/decapping die. The priming chamber is a #2. There is another die with a decapping stem that appears it could be a universal type decapper or maybe for a straight or slightly tapered case (?), no number on it at all. Another die has the number 15 on it and appears it could be for neck sizing a case. The last one looks as if it could be another sizing die and is threaded at the top as if to take a seating stem, flaring tool or? There is no number on it either. Any help appreciated.

[Pavogrande]

1 = 223 full length die -- not seen a bottle neck fl die before -
2 = #2 PC = 30/06 head
3 = right universal decap die
4 = #15 is a 30.40 muzzle resizer
5 = probably an expander die -- generally about 3/8 thread -- .395 actually -- short, med, and long plus some others


oops i goofed forgot the pc

[NoZombies]

1 = 223 full length die -- not seen a bottle neck fl die before -
2 = #2 PC = 30/06 head
3 = right universal decap die
4 = #15 is a 30.40 muzzle resizer
5 = probably an expander die -- generally about 3/8 thread -- .395 actually -- short, med, and long plus some others


oops i goofed forgot the pc

The #1 is a trueline JR die. (the 310 dosn't get enough leverage, but the TLJR does)

[sharps4590]

Thank you, that's definitely more than I knew before!!!!

[mew]

I have accumulated these 310 dies over the years and have never used them or have a need. I want to move them along to someone who collects and/or uses the 310 and hopefully one of you are interested. My primary goal is to get them in the hands of someone that will enjoy them and get something in exchange I can use. I would swap them for LE Wilson trimmer and/or case holders or RCBS dies and/or die parts. Pretty open. If you have something you want to move along, run it by me.

Bottom to Top:

Left Column:

#2 shell holder
429 Seater w/421 stem
Decapper minus pin

Right Column:

153 Seater w/450 stem
266 Expander
287 Expander

216759

[Wayne Smith]

Left column #2 is a #2 priming chamber. It fits the -06 case head, large primer, which is probably the most useful priming chamber they made given the variety of cartridges that use this case head, including the 45ACP.

[mew]

Left column #2 is a #2 priming chamber. It fits the -06 case head, large primer, which is probably the most useful priming chamber they made given the variety of cartridges that use this case head, including the 45ACP.

Thank you Wayne. I have never used a 310 and relying on some research. You are correct. It will fit all -06 based cases including all .308 based cases as well as .45 ACP. Way too many to mention them all. I hope someone here wants them. I am more interested in getting them in someones hands that will use them than anything.

[Rimfire]

WTT Have 310 44-40,45acp,38spec dies. Sizer ,seating & priming 30-30 dies Also 32special size and 2 seating dies for trueline press. 2 hand sizeing dies 1 30-30 and 1 32 special. 2 handles 1 lg 1 sm. 1 45-70 priming die. Looking for 35 Remington mould FN Rcbs or similar,32-20 brass,25-35 brass and bullets. 38-40 mould that casts a bullet .403 dia. or larger. My 401 mould is to small. Also need a receiver sight for 336 Marlin.

[mew]

WTT Have 310 44-40,45acp,38spec dies. Sizer ,seating & priming 30-30 dies Also 32special size and 2 seating dies for trueline press. 2 hand sizeing dies 1 30-30 and 1 32 special. 2 handles 1 lg 1 sm. 1 45-70 priming die. Looking for 35 Remington mould FN Rcbs or similar,32-20 brass,25-35 brass and bullets. 38-40 mould that casts a bullet .403 dia. or larger. My 401 mould is to small.

Rimfire, I just sent you a PM. Actually TWO PMs.

[mew]

These dies are still available for trade.

[jrmartin1964]

I have accumulated these 310 dies over the years and have never used them or have a need. I want to move them along to someone who collects and/or uses the 310 and hopefully one of you are interested. My primary goal is to get them in the hands of someone that will enjoy them and get something in exchange I can use. I would swap them for LE Wilson trimmer and/or case holders or RCBS dies and/or die parts. Pretty open. If you have something you want to move along, run it by me.

Bottom to Top:

Left Column:

#2 shell holder
429 Seater w/421 stem
Decapper minus pin

Right Column:

153 Seater w/450 stem
266 Expander
287 Expander

216759

As has already been stated, the No.2 Primer Seater will work with any rimless cartridge with the same head size as the .30-'06. The tool No.429 with No.421 plunger is a bullet sizing dies (0.429 diameter), and the plunger is designed to fit the nose of the Lyman No.429421, and is used to size the bullet base-first using the plunger against the nose (as when sizing with a bench mounted lubricator/sizer). Die No.153 is a Double Adjustable (aka Bullet Seating) die for the .270 Winchester. The No.450 Seating Stem is designed to fit the Lyman No.224440 bullet, but likely also will work with some other projectile suitable for use in the .270.

Jim

[Green Frog]

Does anybody have a spare priming chamber (PC) #10 they could swap or sell? Please answer here or with a PM. TIA!

Froggie

[mew]

As has already been stated, the No.2 Primer Seater will work with any rimless cartridge with the same head size as the .30-'06. The tool No.429 with No.421 plunger is a bullet sizing dies (0.429 diameter), and the plunger is designed to fit the nose of the Lyman No.429421, and is used to size the bullet base-first using the plunger against the nose (as when sizing with a bench mounted lubricator/sizer). Die No.153 is a Double Adjustable (aka Bullet Seating) die for the .270 Winchester. The No.450 Seating Stem is designed to fit the Lyman No.224440 bullet, but likely also will work with some other projectile suitable for use in the .270.

Jim

Thanks Jim. Way more information than I was willing to dig around for. I'm really hoping someone can use or appreciate them. I am more interested in getting them into the hands of someone that will use/appreciate them than what I get in exchange. Where they sit now, they are of no use.

[mwells72774]

Looking to sell or trade 2 tru-line presses, small alloy handles, 310 dies- 222, 7x57, 30-40 krag, 38/357. Getting out of tiny dies

[Green Frog]

Does anybody have a spare priming chamber (PC) #10 they could swap or sell? Please answer here or with a PM. TIA!

Froggie

Never mind... My #10 PC somehow got mixed in with my 32 S&W stuff. I'm good now! :bigsmyl2:

Froggie

[BrassMagnet]

Speaking of 32 S&W, who has a spare 310 set and what do I need to trade for it?

[Green Frog]

Speaking of 32 S&W, who has a spare 310 set and what do I need to trade for it?

I probably could put together a set if you can't find one elsewhere. I need to keep a set for my 310 and one for my TruLIne Jr (dedicated) but if there are enough left over parts I'll let you know. Would you be interested in a couple of the dies to start building a set??

Froggie

[BrassMagnet]

I probably could put together a set if you can't find one elsewhere. I need to keep a set for my 310 and one for my TruLIne Jr (dedicated) but if there are enough left over parts I'll let you know. Would you be interested in a couple of the dies to start building a set??

Froggie

Yes!!!

[Green Frog]

Well Magnet Man, somewhere between the event horizon and the actual black hole in my basement there should be some boxed sets classified as trading material. I had the previously mentioned TL Jr boxed set for 303 Brit as well as a backup set of 310 dies for 32-40 and another for 32 S&W Long. Organized people don't make the exciting discoveries I do, but at least they can find what they actually have when they need it! [smilie=b:

Froggie

[BrassMagnet]

Well Magnet Man, somewhere between the event horizon and the actual black hole in my basement there should be some boxed sets classified as trading material. I had the previously mentioned TL Jr boxed set for 303 Brit as well as a backup set of 310 dies for 32-40 and another for 32 S&W Long. Organized people don't make the exciting discoveries I do, but at least they can find what they actually have when they need it! [smilie=b:

Froggie

I need the 32 S&W Long!

[BrassMagnet]

Still needing 32 S&W and 32 S&WL dies for 310 or TrueLine Jr. I even posted a WTB in S&S!

[Green Frog]

All I've found so far is a spare 311 expander die and maybe a spare #9 PC. I've gotta get organized (maybe next year! :roll:)

Froggie

[Wayne Smith]

Still needing 32 S&W and 32 S&WL dies for 310 or TrueLine Jr. I even posted a WTB in S&S!

Sorry, I'm using mine!

[hd09]

Hi all, Looking for a 1/4 x 30 tpi locknut for a seating stem. will trade a 5/8 x 30 tpi lock ring for die body. Or whatever is fair trade.
Thanks Dale

[dsh1106]

Hi all, Looking for a 1/4 x 30 tpi locknut for a seating stem. will trade a 5/8 x 30 tpi lock ring for die body. Or whatever is fair trade.
Thanks Dale
Dale

PM me your info and I'll send you one.

Scott

[sigep1764]

I have question you guys might be able to help with. I have a large steel handle set marked for 270Win. After I finish paying for the new truck in a couple months, Id like to pick up a bolt action in 223/556 and a set of 310 dies/shell holder for 222 Remington. Will my large handles work or do I need a set of small handles?

[square butte]

My 222 set came with small handles

[Green Frog]

Working from memory here, but I believe you can do that... be aware that the adaptor ring is not used with the older, fixed caliber handles, but you should be able to do it. As for length concerns, some of the old loading manuals show 223 as being “either/or” so again, you should be fine. It doesn’t cost anything to try, at worst you’ll find you need another set of handles, but I think you should be able to get by.

Froggie

[sigep1764]

Green Frog, Ive got a funny set. They're large, steel, marked 270, but have the replaceable adapter. Why they would designate a caliber when caliber can be changed I have no idea. Thank you for the info and you're right, worst case is ill have to have another handle set, which would lead to more dies... Maybe I'll get a new handles set!

[Green Frog]

That is a funny set sigep1764, I don’t know whether that was a modified set of handles or one that was made by Lyman just to use up old handle castings during the transition from single caliber to “universal” handles. Either way, it’s another case of “never say never” with Lyman. I’m definitely leaning toward thinking you should be fine with a set of Remington 222 dies in those handles to load 223/556. Best of luck.

Froggie

[sigep1764]

Thanks Froggie. I definitely have time to acquire what I need. The .222 dies are readily available on Ebay and Ive got 2 or 3 months before I save enough to pay off the rest of the truck. Reward is the new rifle, full length sizing die, mold, and 310 stuff for it. Then its on to saving 6 months for a house. If the 222 dies end up wishy-washy, I'll pony up for a set in .223/5.56 from cny, but with the large handles and the adjustability of the 310 dies I think it'll work. The handles I have are wonderfully smooth and a good fit in the hand.

[trooperdan]

A Ruger American in .223 would be a fine rifle for you!

[sigep1764]

It's on the list along with the Mossberg MVP and Thompson Center Compass. The Ruger sur to price and reputation, Mossberg for price and magazines, and TC for 5r rifling and price. They all have attributes, but will all fall to local availability then to pricing. They all have excellent reputations.

[BrassMagnet]

That is a funny set sigep1764, I don’t know whether that was a modified set of handles or one that was made by Lyman just to use up old handle castings during the transition from single caliber to “universal” handles. Either way, it’s another case of “never say never” with Lyman. I’m definitely leaning toward thinking you should be fine with a set of Remington 222 dies in those handles to load 223/556. Best of luck.

Froggie

Check and see if the "bumps" have been replaced with a removable spring steel piece!

[BrassMagnet]

I'm looking for "Special" steel handles, 43 Spanish handles/dies, 348 Win handles/dies, 32 S&W/32 S&WL handles/dies.

[sigep1764]

It does have the replaceable spring steel piece, Brass. I've been pretty happy with them. Im putting together an ammo can kit to reload on vacation here in a couple weeks.

[trooperdan]

I just did 100 rounds of .30-30 using my 310 tools, the expander design in the 310 dies was and is just superb!

[BrassMagnet]

It does have the replaceable spring steel piece, Brass. I've been pretty happy with them. Im putting together an ammo can kit to reload on vacation here in a couple weeks.

So it is a Steel "L" made from handles marked with a specific caliber.

[sigep1764]

Yup, came with the original box too!

[Earl Brasse]

I need some deep help...

Mainly, I'm looking for 310 .41 Long Colt dies. (or at least the #72 seater die) and a set of Steel handles caliber marked ".41 Colt".

I need these to replace the ones the previous owner butchered so he could load heel base .401's instead of hollow-based .386's.

He cut off a large part of the die & off-center drilled out the nice plum handles & altered the pin & ground on the handles. (really evil)

I am also looking for (in nice for using):
steel handles, 32-20 Win., 38-40 Win & 44-40 Win.
maybe a set of .45 a.c.p. dies

I don't have any really interesting 310 or Tru-Line Jr items for trade just dies for .38 spec., .44 spec, (Have a set of steel .257 REM. handles to trade on handles)
but do have a bunch (pounds) of parts for Colt Signature Series blackpowder revolvers, Walkers , Dragoons, 1849, 1851 Navy, 1860 Army.

Or might have other old reloading stuff to trade.

Or willing to buy.

Thanks

[BrassMagnet]

I see light between mould halves, so more for collecting than using!

32-20 & 38-40

224130
224131
224132
224129

Available to trade for 310 stuff!
With the light showing between the mould halves, I wouldn't cast with them. The other four that came with these do look nice and I am keeping them!

[Earl Brasse]

Thanks for the offer Brass Magnet, but like you I'm looking for nice usable stuff (that I can also look at).

I have a horrible example of an Ideal in .41 Short that suffered unspeakable cruelty but will relate here as a horror story to be told when the campfire burns low..

Cut down mold halves to make thinner to rebore, bored thru & other side tapped for HP, middle of mold & ends of handles trimmed so it would close. A sad end for a rare Ideal tool.

[BrassMagnet]

I see light between mould halves, so more for collecting than using!

32-20 & 38-40

224130
224131
224132
224129

Available to trade for 310 stuff!
With the light showing between the mould halves, I wouldn't cast with them. The other four that came with these do look nice and I am keeping them!

These aren't too bad! Anyone interested?

[dsh1106]

I need a neck expander for a 45-70 310 set.

I have a few 310 dies available for trade

30-06 set
257 Roberts set
300 H&H seating die
Universal decapping die

Scott

[Hamish]

Looking for a 310 8mm Mauser neck size die. Also, one or two Lyman #17 J type shell holders.

Have a hand full of other 310 dies to trade, need to document them,,,,,.

Rich

[BrassMagnet]

I'm looking for "Special" steel handles, 43 Spanish handles/dies, 348 Win handles/dies, 32 S&W/32 S&WL handles/dies.

I found Special handles. Still looking for the rest!

[square butte]

Anyone happen to have an extra adapter ring for a .22 Hornet set that they could afford to part company with? I just acquired a set that was missing the adapter

[BrassMagnet]

Quote Originally Posted by BrassMagnet View Post

I'm looking for "Special" steel handles, 43 Spanish handles/dies, 348 Win handles/dies, 32 S&W/32 S&WL handles/dies.

I found Special handles. Still looking for the rest!

I found a set of 32 S&W dies!
WooHoo!!!

[trooperdan]

I found a set of 32 S&W dies!
WooHoo!!!

Aw No Way! Really glad for you, one less in competition with me for a set! )

[Pumpkin]

Dan; I have a set of S&W 32 310 dies bought in the 70's,maybe loaded a box of shells, put away and almost forgotten.
In the black and white (gray now) Lyman box. Let me know, if interested,---maybe we can work out a trade.

[BrassMagnet]

Dan; I have a set of S&W 32 310 dies bought in the 70's,maybe loaded a box of shells, put away and almost forgotten.
In the black and white (gray now) Lyman box. Let me know, if interested,---maybe we can work out a trade.

I can trade if Dan can't!

[trooperdan]

Dan; I have a set of S&W 32 310 dies bought in the 70's,maybe loaded a box of shells, put away and almost forgotten.
In the black and white (gray now) Lyman box. Let me know, if interested,---maybe we can work out a trade.

Darned right I'm interested! I sent a PM! Dan

[Pumpkin]

Brass Magnet; Trooper Dan and I worked out a trade on 32 dies. Thank you for your interest. Regards,
Marvin, aka Pumpkin

[Green Frog]

Although Lyman seems to be actively cutting back on their selection of 310 dies, it seems that 32 S&W L and H&R would be a good one to add at this time, no special tooling for them to make up and an ”Ideal” caliber for the tong tool as well as the TL JR. (Pun intended.). They should be a good seller.

Froggie

[Hamish]

Looking for 30 Mauser (7.63x25) dies.

[slug]

I have two sets with steel handles, in .22 Hornet and .222 Rem. I'll trade one for a similar set in .303 British, .38/55 Win or .38/56 Win.
I'm also needing a priming chamber for .45/70
There is no problem dealing internationally, since handloading tools are specifically exempt from ITAR.
Thanks.

https://i.imgur.com/SUKB0o2.jpg?1

[Maine1]

Just got a 310 tool and a set of dies after wanting ones for years. It was a good deal although the dies were not my first choice.

I have a set of 30-06 dies i'd like to trade, and i'm looking for 30-30, 45-70, 38/357 dies, and a set of small handles.


I love to trade, so lets talk.

[Green Frog]

Just got a 310 tool and a set of dies after wanting ones for years. It was a good deal although the dies were not my first choice.

I have a set of 30-06 dies i'd like to trade, and i'm looking for 30-30, 45-70, 38/357 dies, and a set of small handles.


I love to trade, so lets talk.

I should be able to drag out a set of small handles and 38/357 dies, what kind of stuff do you have for trading?

Froggie

[Maine1]

Brass in 45 acp/40/308/223/
lead
what are you in the market for? ive got an Ok assortment of various things guys like us tend to find useful

[BrassMagnet]

I have two sets with steel handles, in .22 Hornet and .222 Rem. I'll trade one for a similar set in .303 British, .38/55 Win or .38/56 Win.
I'm also needing a priming chamber for .45/70
There is no problem dealing internationally, since handloading tools are specifically exempt from ITAR.
Thanks.

https://i.imgur.com/SUKB0o2.jpg?1

I believe I have extra 45-70 priming chambers.

[BrassMagnet]

Quote Originally Posted by BrassMagnet View Post

I'm looking for "Special" steel handles, 43 Spanish handles/dies, 348 Win handles/dies, 32 S&W/32 S&WL handles/dies.

I found Special handles. Still looking for the rest!

I found a set of 32 S&W dies!
WooHoo!!!


I found 348 Win 310 dies. They fit a Special handle, not just a large handle. No adapter. I have a caliber specific steel 348 handle, but I need it for my 41 Swiss CF. So I still need an adapter or another set of 348 steel handles.

Note: It looks like my 50-70 adapter might work, but 50-70 is not on my 310 chart.

[trooperdan]

Hamash, are you still looking for a 8 mm MR?

[BrassMagnet]

I have a Lyman shell resizer and a #126 CMR die. 9 MM Rifle or 9x57 rifle.

[beagle]

Found a resizer. Still need the expander.

Looking for a .30/06 neck resizer die for the 310 tool as well as a .311 expander to fill out a .30/06 set.

I have the following 310 adapters for trade: #2,#1,#6-2each, and a #5. PM me./beagle

[NoZombies]

I'm cleaning up and getting rid of some dupes and excess.

I have a few deals pending, until they're completed, I'm pausing the availability of these to figure everything out. If I'm already talking to you, the pause doesn't effect our deal(s).

.38/357 set complete (with steel handles, other sets do NOT include handles unless noted)
.38/357 set, complete
.357 bullet sizing die and pushrod
.300 H&H partial set
.222 set missing priming chamber, otherwise complete
.222 set with modified priming chamber (works, but has home-made primer ram)
.270 partial set
.270 complete boxed set for new line jr
.300 savage, partial set
.308 partial set
(Set aside to work something out with brass magnet).43 Spanish, complete set, Also have a matching mold...
45/70 complete set + .457 "Kake Kutter" and .457 sizing die and pushrod
8 die adapter rings (allowing 310 dies to be used in standard presses)
Various single dies, and some more sets that I'll add tonight or in the next few days.

I may be talked out of most of a set for .32 S&W long for the right trade, but it'll need to be something pretty special...

Things I'm looking for:
Odd or unique caliber 310 or other reloading dies (must be something I want and don't have already)
Lead (hard is okay, soft is better)
Rare/Uncommon molds (especially looking for obsolete designs that I don't already have, and 2-4-6+ cavity molds of various makes)
Star/magma style sizing dies in .224 .363 .364 .365 .502 .503 .504 .540 .541
I frame or J-frame S&W project gun(s)
(based on that list, if you have something else you think I might like, feel free to ask!)

[JoseBob]

I think I have what you are looking for. If one is a die with 123 on it with 328 on the stem cap is the resizer and the expander with
123 on it with 311 on the cap. If this is what you need, let me know and P.M. me your address.... Bobby

[JoseBob]

Sorry the above reply was for beagle....

[dsh1106]

I'm cleaning up and getting rid of some dupes and excess.

Available:

.38/357 set complete (with steel handles, other sets do NOT include handles unless noted)
.38/357 set, complete
.357 bullet sizing die and pushrod
.300 H&H partial set
.222 set missing priming chamber, otherwise complete
.222 set with modified priming chamber (works, but has home-made primer ram)
.270 partial set
.270 complete boxed set for new line jr
.300 savage, partial set
.308 partial set
(Set aside to work something out with brass magnet).43 Spanish, complete set, Also have a matching mold...
45/70 complete set + .457 "Kake Kutter" and .457 sizing die and pushrod
8 die adapter rings (allowing 310 dies to be used in standard presses)
Various single dies, and some more sets that I'll add tonight or in the next few days.

I may be talked out of most of a set for .32 S&W long for the right trade, but it'll need to be something pretty special...

Things I'm looking for:
Odd or unique caliber 310 or other reloading dies (must be something I want and don't have already)
Lead (hard is okay, soft is better)
Rare/Uncommon molds (especially looking for obsolete designs that I don't already have, and 2-4-6+ cavity molds of various makes)
Star/magma style sizing dies in .224 .363 .364 .365 .502 .503 .504 .540 .541
I frame or J-frame S&W project gun(s)
(based on that list, if you have something else you think I might like, feel free to ask!)

PM Sent

Scott

[rdwarrior]

I'm cleaning up and getting rid of some dupes and excess.

Available:

.38/357 set complete (with steel handles, other sets do NOT include handles unless noted)
.38/357 set, complete
.357 bullet sizing die and pushrod
.308 partial set


Interested in the above items - pm sent to you.
Ron

[Jkrem]

I have the following two 310 dies to trade:

Lyman 30/06 DA, seating stem 366, no locking ring. Actually, the A (DA) stamped on this looks like an upside down V so I may have this wrong...
Lyman 30/06 CMR, neck expander button is .308, includes new decapping pin and the locking ring.

I’ll be trying to assemble a 30/30 set, looking to start with the neck sizing or seating and crimping dies, but any considered.

Jim

[jaxenro]

Hi
I am looking for a set to reload the old 32 S&W (not 32 S&W long)

I have a set of I think 38 special or (more likely) 357 I can trade in addition to other considerations

[woody1]

I have nothing for you but would think the same set would do both 32 S&W & Long.

[jaxenro]

From what I understand they made a set specifically for the 32 S&W but if the long set would work i will take it

[Winter Hawk]

Jaxenro, did you get what you need? Are you interested in a Ideal No. 1 for .32 S&W? It doesn't have the dipper or decapping pin, and the box was in really bad shape so I glued/taped on paperboard where it was missing and it is at least functional.

~WH~

[44magLeo]

I bought a set of steel handles marked 3006 awhile back to put in with my 7mm Mauser dies. That may I wouldn't have to swap back and forth handles from another set.
I got it out the other day to play with.
I noticed the hole where you put the cartridge case in the handles was a bit large.
I measured it with my calipers and got about .565 diameter. I think this set of handles was reamed out for something like a 348 Winchester.
Anybody willing to trade a steel set of handles marked with 7x57 or 280 Remington? Even a 30-06 set will be fine.
Leo

[slug]

I have two steel handle boxed sets for trade. One is in .222 Rem and the other is in 8.6 x 56. No, I don't know what cartridge that is.
Both sets are in VG shape however, the 8.6 has no decapping unit. It could have been lost over the decades, or if it were for a Berdan primed cartridge it wasn't used. A different decapping system would be required. The .222 set has found a new home now.
I'm looking for similar boxed sets in .32/20 and .38/56, and steel handles marked for .303 British and .38/55, as well as a .45/70 primimg chamber.
Thanks for the look.

https://i.imgur.com/QJQXK53.jpg?1

[slug]

Pl. remove. duplicate.

[BrassMagnet]

I have two steel handle boxed sets for trade. One is in .222 Rem and the other is in 8.6 x 56. No, I don't know what cartridge that is.
Both sets are in VG shape however, the 8.6 has no decapping unit. It could have been lost over the decades, or if it were for a Berdan primed cartridge it wasn't used. A different decapping system would be required.
I'm looking for similar boxed sets in .32/20 and .38/56, and steel handles marked for .303 British and .38/55, as well as a .45/70 priming chamber.
Thanks for the look.

https://i.imgur.com/QJQXK53.jpg?1

I have the 45-70 PC. I retired last week, so I will have time to search for it while sorting/rearranging.

[sigep1764]

Congrats on Retirement Brass!

[JoseBob]

Congrats Brass...You will enjoy it.....Bobby

[BrassMagnet]

There are two of the early Ideal 32 S&W hand tools with the mould on the end and the integral seating die (not threaded!) on FleaBay. I am not bidding and I don’t know the seller. Search “Ideal Reloading” to find them.

[Maine1]

Recently picked up a set of steel Ideal handles, a bit of plumb coloring left, if that matters, with a # 11 on them.

Also have a 222 Remington seater, and sizer/decap die, an 8mm muzzle sizer without plug,
308/311 bullet sizers with 1 ram, 357 bullet sizer with ram.

3006 size/decap die, short decap pin but stem is intact.


Looking for serviceable set of small handles, #1 adapter (357 mag), #3 priming (357 mag) SPC exp chamber.

Set of 44 mag dies>

Serviceable large handles, 30-30 dies

[jgh4445]

Picked up a set of Nickle steel handles marked 30-06. Marked Ideal, Middlefield Conn. USA. No threads in the adaptor hole. Would like to trade for a set of handles that my new Lyman 310 45-70 dies will fit in to.

[jgh4445]

Traded. Thanks.

[uscra112]

Anybody need the 310 expander mandrel for .270 Winchester? (Stamped 280, mikes .2785/.2820.) Gratis pro Deo. I repurposed the die body, but can't bring myself to just throw the mandrel out. Post here or P/M.

Spoken for.

[15meter]

Looking for a whack-a-mole style sizer for 32 Remington.

If you've got one let me know what kind of trading fodder you're looking for--brass, boolits/bullets, lead or reloading weirdness.

[trooperdan]

Just realized I need a priming chamber #14, used for .38-40, .45 AR and .44-40. Anyone have a spare one? What do you need in trade, I have a bunch of 310 stuff.

Well, disregard! I found a new #14 and it does NOT for .45 AR! Anyone using 310 tool to prime .45 auto rim, what PC are you using?

Edit! Looks like I cross-eyed the chart when I said a #14 should work, looked again and I think it should a #17! Does anyone have a spare #17?

[wonderwolf]

Looking for the following for the tong tool

#23 priming chamber (30 carbine)
#17 shell adapter (9mm)
#150 Muzzle resizer (44 special)
#9 Shell adapter (44 special)

Also looking for 303 Savage die set as well as 32/20?

Have some odds and ends in 310 stuff to trade and a lot of other misc items, I'm sure we can work something out. PM or email me.

[slug]

I need a .377 neck expander.
Also, looking for steel handled sets in .303B. .38/55, and .38/56,
Also a solid set of steel handles of almost any cartridge, since I plan to open it up to take .38/56.
I have two steel sets for .22 Hornet, but I sold my last Hornet a while back.
I also have a two die set of Tru-line Jr. dies, NIB, for .30/30.

I may put up my steel set in .45/70 up for adoption, if I sell my last two .45/70's.

https://i.imgur.com/hj3SlE5.jpg

[uscra112]

I have a 310 expander die assembly, expander mandrel marked .308. Probably suitable for most .30 calibers except .30-06 may be too long. (??). A bit grungy but no rust. Yours $10 shipped in a flat-rate box. No trades needed at this time. P/M me.

Spoken for as of 08:00 26 Oct 2019

[Pressman]

Reminder: This is a trading forum. Open sales will get it all shut down. If you want to sell only then please post in Swap & Sell.

[44magLeo]

I posted awhile back about a steel set of 310 handles They are marked 30-06 but the hole where the case goes through the handle is way to big. About .565
I took some pics to post so you can see the shape they are in and the case hole and die thread diameters.
The pitting you see is not very deep. Only in one small place can you feel them.
Leo

[uscra112]

???? That's a clearance hole, size doesn't matter as long as the .30-06 case can pass through it. If it bothers you, make a bushing for it.

[Pressman]

Did you try threading a die into it? Wondering about thread size.

[Gewehr-Guy]

I examined a steel 270 marked set of handles, and they measure .573 where the die threads in, and .477 where you insert the case. On your handle , they just bored all the way through before threading, and some must have been drilled part way, and left a caliber specific hole on the inside of the handle. Should not be a problem, as the sizing die supports the case well and keeps it straight.

[Pressman]

I just spent an hour measuring 310 tool hole sizes. 30-06 range from .4715 to .4760. Die thread is .6075x30 for the medium dies, .652x30 for the large dies.

[44magLeo]

This set of handles are the standard threading for 310 dies. The larger Special dies won't fit.
The hole is not bored all the way through then threaded.
If you look at the pics you will see the hole is .565 in diameter. The threaded portion is .595.
I've threaded holes before. With a hole .030 to small you can't thread it. No room for displaced steel to go.
With this much play around the case in this hole allows to much misalignment when sizing and bullet seating.
Leo

[Eddie Southgate]

Just realized I need a priming chamber #14, used for .38-40, .45 AR and .44-40. Anyone have a spare one? What do you need in trade, I have a bunch of 310 stuff.

Well, disregard! I found a new #14 and it does NOT for .45 AR! Anyone using 310 tool to prime .45 auto rim, what PC are you using?

Edit! Looks like I cross-eyed the chart when I said a #14 should work, looked again and I think it should a #17! Does anyone have a spare #17?

14A is the correct shell holder for the Tru Line .

[slug]

I'm looking for a steel handled set for .250 Savage.
My trading stock is sets in .218 Bee, .22 Hornet, .22 K Hornet, .30/30 and .30/40.

[dsh1106]

I need a #95 MR die. Some how I've miss placed this piece.

I have a handful of 310 items available and some other "stuff". I'm sure we can come up with a trade.

Let me know what you need.

Thanks
Scott

[Green Frog]

I've got one for you Scott. I'll have to dig it out, but I think it should be near the surface. Drop me an e-mail.

Froggie

[sigep1764]

If anyone has a set for 30-30 including handles, I would trade straight across for a set in 9mm with handles. Not pretty, but the set makes good ammo.

[curdog007]

I have a 257 set looking to trade for 32-20 310 tooling

[Pavogrande]

I need a DA 8mm also marked 118 -- will trade a 7.62 russ or 303 brit da or what ever you want that i have -

want to complete set to trade for another caliber i shoot -

perhaps someone wants to trade for the incomplete set ?
30/40 - 250 - 30 rem (not bloody likely), 44/40 wanted -

[Green Frog]

I’ve assembled most of a nice 310 die set in 32 S&W for a friend, but I still need the priming chamber. Does anybody have a spare #9 they can trade? I’ve got some really off-the-wall stuff somebody is bound to need.

Froggie

[Pavogrande]

41 mag #30 priming chamber -- swap for #10 32/20 or #23 30carb or #15 30rem

[Green Frog]

Pg - the #19 PC is what I have in my notes for the 30 Carbine. What was your source for the #23? I think I may have a spare #23 if that actually works, and I just got a spare #10 in a swap with MS. You wouldn’t have a #9 to spare would you? :)

Froggie

[Pavogrande]

hi froggie -- 2 sources -- stoegers 1956 and my compete set -
checked my set, it fits -- checked stoeger 19 is for 22 lovell -- probably 25 ss as well --
no spare 9 --

ps -- ever seen a set for 30 rem ?

[Green Frog]

Strange.. it looks like some of the numbers may have changed over time. Yes, I saw the #19 listing for 25-20 SS and its derivative, the 22 Lovell, but it was also listed for 30 carbine(?) It seems like there may have been some misprints, but there also may be some crossover as head sizes accidentally fit.

I did get lucky and find a #9, so I can call off the dogs on that hunt.

IIRC, I had a 30 Rem set about 15 years or so ago, but swapped it off to a friend in NC. You don't see them that often.

Froggie

[Green Frog]

Well, as I was looking for the #95 CMR for Scott and a couple of other things, I went through a bunch of orphan dies and located some for 243, 303 Brit and of course 30-06 as well as a couple of the more obscure rifle calibers and a very few pistol calibers as well. Does anybody else need something odd to finish a set??

Froggie

[curdog007]

I'm needing a #15 priming chamber. Have a box full of misc. 310 stuff coming hopefully later this week, so I'll see if there's anything in there worth while to trade.
Just picked up the Lyman whack a mole FL resizers for 32-20 and 25 Remington, so those sets are getting complete.
The Model 8 and 92 SRC will be happy.

[slug]

I need a .377 neck expander plug. I have the die body. TIA.

[PHyrbird]

I've a 357 "M" expander stem but don't have the die shell to screw it into the handles or the trueline press. Any data on which die body I need? I'd b using it for several calibers i load if I could figure out which one to get.