Veral Smith is he still around?

[omgb]

Greybeard has no posts to his forum. Is he still alive and kick'n?

[jmort]

Yes. Call him:



Have a comment or question about one of our products? Feel free to contact us using any of the methods below. Please keep in mind we are in Mountain Time Zone and that I may be in the shop at the time of your call. However do leave a message and I will get back to you as soon as I can. - Veral SmithLead Bullets Technology
A Division of
F.I.G. ENT. INC.
78592 Hwy 2
MOYIE SPRINGS, ID 83845
1 208 267 3588

LBTisAccuracy@localnet.com

[JonB_in_Glencoe]

I ordered his book, it arrived a week ago. My Christmas present.

[rush1886]

Yes. Call him:



Have a comment or question about one of our products? Feel free to contact us using any of the methods below. Please keep in mind we are in Mountain Time Zone and that I may be in the shop at the time of your call. However do leave a message and I will get back to you as soon as I can. - Veral SmithLead Bullets Technology
A Division of
F.I.G. ENT. INC.
78592 Hwy 2
MOYIE SPRINGS, ID 83845
1 208 267 3588

LBTisAccuracy@localnet.com








Veral is getting some long in the tooth. And, he can be a cranky old machinist/bulletsmith. With all of the noise in the shop, I've found it best to contact him by email. He does read those, and will respond, but as with most of us greybeards, too much noise over too many years, makes hearing, i.e. the phone, iffy at best.

[M-Tecs]

I also recommend email. Called him once about 6 years ago. Talked for about 90 minutes but only about a minute on my subject. After that emails only.

[Mike W1]

LBTisAccuracy@localnet.com

Just tried that email address and it bounced. Is it typed correctly???

[MrWolf]

Here is a link to his page:

http://www.lbtmoulds.com/contactus.shtml

[tja6435]

He's still kicking out molds, I've ordered 3 from him over the last 2 months along with 40 sticks of his lube, lapping kit, push through slugs, bhn tester, etc. He called me to verify my mailing address and is a bit hard of hearing on the phone, but we got it all worked out just fine.
If you want to order something, just send in his order form with your check and you'll get it a few weeks later.

[reloader4410]

Some of the best of the best molds you will ever cast with. Happy New Year, & Happy Trails.

[Mike W1]

Here is a link to his page:

http://www.lbtmoulds.com/contactus.shtml

Thanks, I'll give that a try.

[facetious]

I ordered his book, it arrived a week ago. My Christmas present.


I got that book in the late 80's /early 90's . there is a lot of good info on how and why cast work the way thy do. I have two molds from him, .358 150-OWC, and a 170-LNLC for my .308

[MT Chambers]

His molds and designs are as good as it gets, but are aluminum only.

[dannyd]

Also got his book back in the 80's, still read it from time to time

[krems]

His book is a classic. I've read through it a number of times. I've never casted an out of round bullet with one of his molds yet!. Some molds run better than others...I have a few where the pins are really tight and are difficult to operate. His bullet lube is worth getting as well. Glad to hear he is still kicking out the molds.

[minmax]

I just got an email from him, about his book and lapping kit 2 days ago. LBTisAccuracy@localnet.com