PDA

View Full Version : Official 45-70 Lyman 310 Thread



Just Duke
03-17-2008, 08:26 PM
Does anyone own one of the 310 tools for 45-70?

Does it work and work well?

Can you use cast bullets?

What vendors are they available from?

Aftermarket dies or parts available?

I feel this would be a great pack tool for month long hunting trips. i.e. 2 months in the Alaskan Wilderness

TIA,
Duke




.

floodgate
03-17-2008, 08:52 PM
DUKE:

Yes;

Yes;

Yes;

Lyman: Handles (Large) Stock #7000058, $52.70; Die Set, #7020120, $59.95; Carrying Pouch, #7000059, $9.95. Or, slightly cheaper from Randy Davis' "The 310 Shop", <www.the310shop.com>, as well as from Midway, Midsouth, etc., etc.

The 310 Shop has assorted 310 dies and adapters in many other calibers, including a bullet sizing die that can be used with the 310 tool @ $15.00.

The 310 is the most compact of the current crop of non-bench-mounted tools, though slightly slower than some; it'd be a fine choice for your purposes. Fun, too!

floodgate

Just Duke
03-17-2008, 08:56 PM
Thanks for the fast response sir. :-D
Which of the above is a forum supporter? I like to use vendor affiliates. :-D

StrawHat
03-18-2008, 06:25 AM
Floodgate has given a pretty good summation for the 310 tool.

I load for 3 rifle with mine, 45-70, 405 WCF, and 22 WCF.

A great tool that has few limitations, I use it at the range to test loads.

The only "problem" I see is that you can not keep up with progressive presses.

Not a big deal unless you are shooting a handgun.

floodgate
03-18-2008, 01:05 PM
DUKE:

None of the listed sellers of 310 tools is a supporter of this site, as far as I know. Randy has looked in from time to time, and I have bought, sold and swapped parts with him for a couple of years. Check them all out and make your own choice.

floodgate

Just Duke
03-18-2008, 02:03 PM
I just talked with Randy at the 310 shop he seems like a nice enough fellow. :drinks:
Looks like I am going to get the handles at $55.00 new and the dies runs $55.00 with $6.00 shipping.
Does anyone have a good pic ofthe 45-70 dies and Handles?

floodgate
03-18-2008, 02:18 PM
DUKE:

Glad you went with Randy; I'm sure you will be satisfied with his 310 stuff. I don't have a photo of the 310 set handy just now - and you'll probably have yours in hand before I "get around to it" - but here's one for you to check out: the old Ideal No. 5 tong tool made primarily in .45-70 from around 1890 up to WW I:

http://img.photobucket.com/albums/v317/floodgate/P1010001_1.jpg

If you spot one of these, complete, for anything under $200, either grab it yourself, or let me know ASAP!

Good luck, and enjoy your new 310 tool.

Doug

Junior1942
03-18-2008, 02:43 PM
I got the best accuracy from both of my Handi 45-70 barrels with Lee whack-it Loaders. I bought one for each barrel. In fact one barrel has two of its own due to my shooting two different bullets in that barrel.

mazo kid
03-18-2008, 02:55 PM
WOW!! Doug, is that what the 45-70 tong tools are bringing? ! have 26+ tong tools, a couple are duplicates, and the most expensive one was $79.00 with the de-cap pin. Bought my 310 set in 45-70 several years ago and think the complete set cost around $50. I wonder if my wife knows how much these items will be worth in a few years? Guess I'll start an inventory list for those too! I HAD a tong set in the orange box for 50-70 and foolishly sold it to a buddy. MAN!! When I see what those are bringing now.... Emery

floodgate
03-18-2008, 03:33 PM
mazo:

That's just for the No. 5, a very specialized tool. Others would be the No. 2 for the S&W .32-44 and .38-44 No. 3 break-open target revolvers, the No. 7 for the M-H .44 XL shotshells, and the No. 8 for loading the HB bullets for the .32 & .38 Colt "inside-lubed" pistol cartridges. The No. 1's (small pistol ctgs.), No. 3's, ("The Rifle Crank's Friend"), No. 4's (short rifle & pistol) and No. 6's (large rifles), and No. 10's (rimless rifle and pistol) are in the $75-150 range, depending on condition and completeness - rare or specialty calibers and versions considerably higher. There apparently never was a No. 9. The "310" evolved from the No. 3 and No. 10, by addition of the separate priming die. A few of the steel-handled 310's can be pricey, too, especially those with the oversize dies for 8mm Lebel, .348 and the .50-70. PM or e-mail me if you want to go deeper into these, or look at the Antique Reloading Tool Collectors Ass'n. site at <www.antiquereloadingtools.org>.

Doug Elliott

hydraulic
03-18-2008, 09:02 PM
310 tools are on page 344 of the Midway catalog. .45-70 dies are $56.99 and large handles are $51.99. This is a set of .30-06 that I use alot. If you click on the picture it will enlarge and you can see the price tag (upside down) which is $10.00. Of course, that was with a set of steel handles. I probably should mention that I bought this at a gun show in Columbus, Nebraska in 1978. I remember the year because they were celebrating their centennial that year.

Baron von Trollwhack
04-10-2008, 10:09 PM
FWIW, I use my 45-70 tool to load 45-60. BvT

rockrat
04-10-2008, 11:00 PM
Can't believe they are so high. I have picked up many a set for $20 or so, handles usually for $15. Even picked up a steel handle that was nickle plated and marked 250-3000, but no dies.

Dale53
04-10-2008, 11:49 PM
I much prefer the Lee Hand Press. It can full length size with its compound leverage, it uses standard dies and it can be had from F&M Reloading for $21.99. It weighs a mere 1.5 lbs.

This is a good piece of gear. It is VERY useful for "on the range" reloading.

I also have an original Lee Turret press that can be housed in it's own wooden box for carrying and/or storage that can be used as a mounting stand for the press. I have often worked up loads at the range with MUCH faster results than loading "five of this and five of that" at the home shop for transport to the range.

Dale53

Old Ironsights
04-11-2008, 10:40 AM
I got the best accuracy from both of my Handi 45-70 barrels with Lee whack-it Loaders. I bought one for each barrel. In fact one barrel has two of its own due to my shooting two different bullets in that barrel.

Agreed. I'm not even going to try loading .45-70 on anything bt my Lee Loader. (I don't keep 2 loaders, but I do make a "LockNutSet Dummy for each of my different boolits...)

Really, I can totally see where pistol cartridges are/can be a pain on a LL, but for Bigguns like the .4570, and Shotties I really can't see anything else being more "user friendly" or safe...

Racer X
04-11-2008, 12:19 PM
Wow! I didn't know they brought that kind of money. Why are they worth so much? My uncle left me several of them, some Ideal, some Lyman. Calibers include 45/70, 38 Special/357 Mag, 22 Hornet, 22 K-Hornet.

Just Duke
04-11-2008, 12:40 PM
Wow! I didn't know they brought that kind of money. Why are they worth so much? My uncle left me several of them, some Ideal, some Lyman. Calibers include 45/70, 38 Special/357 Mag, 22 Hornet, 22 K-Hornet.

Would the 45-70 be on the market? :-D

KCSO
04-11-2008, 01:34 PM
Here is my Pac kit, I currently have one in 30-30, 38-55 and 7.65 Mauser along with assorted dies for other calibers. The old flask is handy as it drops just the right charge of Unique for my small game load for the 30-30. I have had one of these kits in 45-70, but since I only used that for target and Buff hunting I didn't use it much. In the late 60's early 70's i used a 310 to load all my 45-70 for my trapdoor. Lubed the sas cast bullets in a pan and squeezed them into the case over 70 grains of Dupont FFg in old military cases F/A 89-92.

StrawHat
04-12-2008, 08:17 PM
KCSO

Nice set up for the 310.

Guess I know what one of my next projects will be, currently using a shoebox to hold my stuff!

Boerrancher
04-13-2008, 10:41 PM
I have a 310 tool for my 45-70, 300 sav, 45 LC, 300 win mag. When I would go out hunting for long stays I would take them with me. Another great thing about them is once you work up a pet load it is easy enough to make a powder dipper and keep it in the box with the dies. Then there is no need for a bench mounted powder measure. I can also sit and watch TV and load shells.
The 310 tool is likely the most versatile reloading set up ever made. I wish I could get my hands on an older one for the 45-70 and 45 LC that has the bullet mold built in to the tool, so you can cast your own boolits with the same tool you reload your ammo with. The few I have seen out there are all very old and not in that great of shape.

best wishes

stillhunter
04-14-2008, 03:58 PM
Agree with all of the above. The 310 sets do appear on EBay frequently. You may with patience get one at considerably less than current retail. You might also consider the RCBS coyboy 3 die set. The 3rd die is the M die that bells the mouth for cast bulletts. The only difference is that the 310 neck sizes, while the RCBS full length resizes. Neck only works fine in my guns. I love my 310's, but the cowboy set in a Lyman Spar T is a lot more productive and a lot less tiring to use. If you are starting out, Spar T's can be had for around 90.00 in good shape on EBAY. Good luck!!.

stillhunter
04-14-2008, 04:03 PM
Boerrancher I've tried this and I can tell you to purchase a pair of really thick gloves!! Afrikanier??

badgeredd
04-14-2008, 05:31 PM
Does anyone own one of the 310 tools for 45-70?

What vendors are they available from?

I feel this would be a great pack tool for month long hunting trips. i.e. 2 months in the Alaskan Wilderness

TIA,
Duke


.

I was just on this site and they have the 310 also plus some cool goodies! http://www.trackofthewolf.com/

I did notice that brass for my 40-65 is cheaper here and there were a couple other things I found to be cheaper.

Thanks for your help in the past.

KCSO
04-15-2008, 03:36 PM
Boer
I have cast a lot of bullets from the older toos. I currently have 38 S and W, 30-30 and 38-55 in the shop. With my 30-30 tool i can cast about 50 bullets before the mouold gets too hot to hold with light cotten gloves. That doesn't sound like much by modern standards but in the early 1900's this would have kept my Grandfather shooting for months. In 38 S and W I can load 2 boxes of shells in two nights. The first night I cast, lube and cake cut the bullets. I usually have to do this in 3 or 4 sessions with time for the mould to cool. Then on night 2 I actually load the bullets into the cases using a dipper and seating and crimping with the tool.

Springfield
05-15-2008, 01:17 PM
I have a nice 45-70 tool, here are a couple of pics. Hell, maybe I should put it up for auction or something, I just bought it 'cause I like old tools.

floodgate
05-15-2008, 02:47 PM
Springfield:

That's a NICE Ideal No. 4 tool in the unusual "non-Special" format (with fixed seating chamber); looks like it is set ip for the 500-gr. GI bullet. I'd be happy to bid on it if you decide to auction it here. The little decapping plug is not show., but these are usually lost anyway, and don't really work very well. What are the stampings on it?

Floodgate

Springfield
05-15-2008, 04:00 PM
Beside the Ideal MFG CO, New Haven, Conn, USA, it says 45-GOV-500. It has 2- 1884 Patent dates on the backside. And I do have the primer knock-out piece. I cast some bullets with it once, worked OK, but I am used to aluminum moulds and I didn't want to heat this up too much.

floodgate
05-15-2008, 08:28 PM
Springfield:

Boy, did I goof, in the rush to get on the road for a trip to town! Not only did I double-post, but I double-posted WRONG! That is, of course, not a No. 4 (which was for pistol and short rifle cases, and usually came with the fixed chamber); it is a NO. 6, but in the uncommon fixed-chamber configuration - most came with the double-adjustable seat/crimp chamber. Not as scarce as the No. 5 discussed and pictured above, but a VERY nice example, especially with the decapping plug. It has the mould alignment peg and sprue-plate pivot screw set-screw added in 1901, but is no later than 1910, after which Marlin - who had taken over the Ideal line - used a script "Marlin Firearms Co." stamp. I am prepared to make an offer on it, or to bid if you decide to put it up for auction here.
Floodgate

Just Duke
03-26-2014, 03:15 PM
Good info

Green Frog
03-26-2014, 05:37 PM
Hey Duke, you must have really been bored to go back 6 years for something to read? I got a kick out of rereading it, though. It was my good fortune to find a plum colored iron handle set marked 45-70 with a good set of correct dies in an only slightly battered original box. Found it on flea-Bay about 10 years or so ago when there were still bargains to be had. :coffeecom I doubt if I could justify the $200 or so that would be its "bargain price" today, but I'm glad I can drag it out and load a few when the spirit moves me. :Bright idea:

Froggie

oscarflytyer
03-31-2014, 10:48 PM
Wow! Kids just gave me a Lyman 310 as NIB complete with set of 308 Win dies - all in unmolested box and wax paper wraps! From their Grandfather's/my FIL's estate (I have 3 stepsons and 2 of our own). Boys have been going through the estate stuff, and occassionally pull stuff out for me they know I will like/love/use. I want them to go thru/get first dibs. But they have sent some very nice stuff my way, and it will all come back to them anyway.

I have always wondered about the 310 tool, but not enough to spend money on it. Now I have one. Prob never use it, as it is NIB. But then... Prob will! Maybe even get another sie set or two. Maybe 45-70 or 30-30, so can load at bench. Either way, it seems very cool.

doc1876
04-05-2014, 01:29 PM
I am new here, so maybe I shouldn't tell you, but I got one off of ebay for $96 and it was the only one I have seen in years, and the next week one in not as good a shape went for $180 on ebay.......If I ever see another, I will let you know

.22-10-45
04-05-2014, 11:25 PM
I like the earlier Ideal No. 3 nickle plated dbl. adjustable tools. I use one marked .25-21-25 for bullet seating .25-25 Stevens. ( the only difference between the .25-21 & .25-25 was case length) These are nice tools to take right out to the range for load workup.

Just Duke
04-05-2014, 11:35 PM
Hey Duke, you must have really been bored to go back 6 years for something to read? I got a kick out of rereading it, though. It was my good fortune to find a plum colored iron handle set marked 45-70 with a good set of correct dies in an only slightly battered original box. Found it on flea-Bay about 10 years or so ago when there were still bargains to be had. :coffeecom I doubt if I could justify the $200 or so that would be its "bargain price" today, but I'm glad I can drag it out and load a few when the spirit moves me. :Bright idea:

Froggie

This came up in a Goggle search I was doing. I past boredom years ago. I need to invent a new word.

Green Frog
04-06-2014, 10:27 PM
You know what they say about the devil and idle hands... it applies to idle minds as well. You need a hobby! :bigsmyl2:

Froggie

triggerhappy243
04-07-2014, 01:52 AM
I think I have a 310 lyman set for the 45-70. I will have to look for it. I inherited it from a close friend.

Lead pot
04-07-2014, 11:31 AM
Duke.

Here is an example between the new and old. The black tool is a modern large handle and it is universal that will work with several 310 dies. It has an adjustable extractor for most calibers.
The nickel tool is my old small handle 310 Ideal that is caliber specific for the .38 spc., .357 or similar cases with the rim diameters of the .38 spec. It has the priming die in it.
The old handles are actually larger than the new.
I have a .44-77 on order from the 310 shop since the first of December so if you want a die made you might have to wait for a spell.

http://i704.photobucket.com/albums/ww43/Kurtalt/IMG_1958_zpsa57020bb.jpg (http://s704.photobucket.com/user/Kurtalt/media/IMG_1958_zpsa57020bb.jpg.html)

Kurt

montana_charlie
04-07-2014, 03:18 PM
He has probably quit looking, Kurt, but others can surely benefit from your information.

The thread was opened to prepare for a two-month trip into the Alaskan wilderness ... six years ago.
That may have been back when he bought two Sharps rifles which he turned out to be dissatisfied with.
( ... damaged in shipping, I think ... )

He found tools he wanted, but didn't say if he actually bought anything, and never made any mention of taking the trip.


CM

Lead pot
04-07-2014, 03:39 PM
I never looked up at the post date.

Just Duke
04-07-2014, 03:49 PM
You need a hobby! :bigsmyl2:

Froggie

I've been considering bullet casting but I don't know. Maybe wood working. I have a hand plane and a saw.............

Just Duke
04-07-2014, 03:52 PM
Duke.

Here is an example between the new and old. The black tool is a modern large handle and it is universal that will work with several 310 dies. It has an adjustable extractor for most calibers.
The nickel tool is my old small handle 310 Ideal that is caliber specific for the .38 spc., .357 or similar cases with the rim diameters of the .38 spec. It has the priming die in it.
The old handles are actually larger than the new.
I have a .44-77 on order from the 310 shop since the first of December so if you want a die made you might have to wait for a spell.

http://i704.photobucket.com/albums/ww43/Kurtalt/IMG_1958_zpsa57020bb.jpg (http://s704.photobucket.com/user/Kurtalt/media/IMG_1958_zpsa57020bb.jpg.html)

Kurt

Thanks for sharing Kurt. This would be a great addition to compliment my Winchester 1886 rifles.
All I can really find are the Alloy handle though. Not sure if I would be will to pay the asking price for vintage steel handles.
Had I not been loosing my eyesight these would have worked great on my Sharps rifle. The sights were just a blur so I sold it.

Lead pot
04-07-2014, 04:31 PM
Duke I have seen them on the gun show tables ranging from $25. and up. I always look for the old moulds and loading tools/dies. Around this part of the country blk powder shooting is not as popular as at other locations of the country and you can still find fine old rifles and stuff that are now bargain prices. Around here if you don't use a Dillon for loading your out of step :)

Just Duke
04-07-2014, 04:41 PM
Say are you the Kurt from the Shiloh Sharps store or Forum?

Lead pot
04-07-2014, 05:04 PM
Yes I am.

Just Duke
04-07-2014, 05:08 PM
Yes I am.

I thought so.

triggerhappy243
04-07-2014, 05:09 PM
OH Damm, out of step? HEH-HEH, I still load all my rifle ammo on a single stage press. but 45 ammo, broke down and got a dillon..... free. still learning how to use it. SLOOOOOOW!

Just Duke
04-07-2014, 05:39 PM
Duke I have seen them on the gun show tables ranging from $25. and up. I always look for the old moulds and loading tools/dies. Around this part of the country blk powder shooting is not as popular as at other locations of the country and you can still find fine old rifles and stuff that are now bargain prices. Around here if you don't use a Dillon for loading your out of step :)

We have the Black Rifle Testosterone Club down here so we don't see much vintage anything.

Lead pot
04-07-2014, 05:49 PM
OH oh now I'm in trouble :)

Nothing wrong with a Dillon, darn good loading press.
If I was a high volume hand gun trigger pulling match shooter I sure would have one. I load one at a time on my rock chucker or on the C&H H and the T-6 but all single stage.

Kurt

Just Duke
04-07-2014, 05:56 PM
OH oh now I'm in trouble :)

Nothing wrong with a Dillon, darn good loading press.
If I was a high volume hand gun trigger pulling match shooter I sure would have one. I load one at a time on my rock chucker or on the C&H H and the T-6 but all single stage.

Kurt

Kurt you know you could run a belt sander over that block and freshen it up. Right?
http://i704.photobucket.com/albums/ww43/Kurtalt/IMG_1958_zpsa57020bb.jpg

Buffalo Arms Co
04-07-2014, 05:56 PM
We carry them, but for a great selection you can't beat Rick at the 310 shop. I've bought a couple of sets from him and have not a single bad word to say about him.

Lead pot
04-07-2014, 06:24 PM
:) If I did clean up that block it would look just like it does two weeks from now :)
I have 3 more that look just like this one does.
I hope I never drop a hot spark on one!

Hank45
04-13-2014, 06:44 PM
Does anybody have contact information for the 310 tool gentleman? thanks for your answerHank45

Rick Hodges
04-15-2014, 11:19 AM
Haha, that loading block is just showing a little character. I remember when people paid extra for furniture that had been beaten with chains and such for a look just like that.

Green Frog
04-15-2014, 02:38 PM
Does anybody have contact information for the 310 tool gentleman? thanks for your answerHank45

Google is our friend. Try this URL;

http://www.cnyauctions.com/the310shop.htm

He is far from cheap, but generally you can get about anything you need from him.

Froggie

Wayne Smith
04-15-2014, 05:21 PM
Froggie, he may not be cheap but he's making them and keeping his prices under the typical eBay craziness.

Green Frog
04-15-2014, 06:01 PM
My sediments exactly! I like to find stuff at a bargain when I can, but when you have to have it and you have to have it now, he's a great source.

Froggie

Just Duke
04-15-2014, 06:17 PM
I remember when people paid extra for furniture that had been beaten with chains and such for a look just like that.

I remember fixing furniture that had been beat with a chain so it didn't look like it hadn't been beat with a chain.
Ask some guy at a car show if he would like his "Dodge Super Bee" beat with a chain so it would have character.

Just Duke
04-15-2014, 06:19 PM
:) If I did clean up that block it would look just like it does two weeks from now :)
I have 3 more that look just like this one does.
I hope I never drop a hot spark on one!

Understood.