View Full Version : Skimmer
armednfree
12-25-2014, 12:19 PM
Rotometals sells this skimmer.
125267
How is that different than taking a stainless searving spoon and drilling a bunch of 1/4" holes in it? I'm talking one you would use in a commercial kitchen and buy for under 10 bucks. I can slice a piece of wood and screw it on the handle.
Pb Burner
12-25-2014, 12:38 PM
A big SS spoon with holes drilled in it works fine for me.
I bought something similar in the kitchen section at the dollar store
tazman
12-26-2014, 09:24 AM
I bought something similar in the kitchen section at the dollar store
Yes! That's what I use. Easy to get, easy to replace, easy to use.
Wayne Smith
12-26-2014, 09:40 AM
I'm not sure I'd go as big as 1/4" for the holes, though. I forgot what number bit I used but it was a whole lot smaller from my numbered drill kit.
btroj
12-26-2014, 09:46 AM
http://i1348.photobucket.com/albums/p733/Btroj/imagejpg1_zps30b89d4c.jpg (http://s1348.photobucket.com/user/Btroj/media/imagejpg1_zps30b89d4c.jpg.html)
I prefer something more like this. It drains lead very well. I melt down lots of range scrap from an outdoor range. This excels at removing jackets while letting the lead drain. Once the jackets are gone I use a ladle to scrape the dirt off the surface.
Jack Stanley
12-26-2014, 10:06 AM
I use one of the old metal ice fishing skimmers when the large pot is running . I do like the idea btroj has for removing jackets and such .
Jack
alamogunr
12-26-2014, 10:17 AM
I use one similar to the one in the OP, although mine looks to be much heavier. I bought it about 15 years ago from Bill Ferguson. I grant you that some of those used by other posters would work better as a skimmer but the heavy one pictured is really good for stirring and fluxing.
It doesn't need replacing, ever! If you don't have a handgun or baseball bat, it will work to hammer an intruder too.
lightman
12-26-2014, 01:09 PM
If you buy a Wallyworld or Dollar Store spoon, make sure its 1 piece or riveted together, not soldered. Ya know why!!!
Sticky
12-26-2014, 04:07 PM
http://i1348.photobucket.com/albums/p733/Btroj/imagejpg1_zps30b89d4c.jpg (http://s1348.photobucket.com/user/Btroj/media/imagejpg1_zps30b89d4c.jpg.html)
I prefer something more like this. It drains lead very well. I melt down lots of range scrap from an outdoor range. This excels at removing jackets while letting the lead drain. Once the jackets are gone I use a ladle to scrape the dirt off the surface.
Just rendered/smelted my first batch of COWWs and used one almost identical to this for skimming the clips off and it works like a champ! That and a sst spoon that I bought at the dollar store for scooping up the dross. Did about half a bucket of weights and came out with about 50lbs of corn on the cob... :O
Well, my ingot mold isn't here yet, so this will have to do for now.
125371
btroj
12-26-2014, 04:26 PM
I have poured better than a ton of range scrap corn cobs. They work well and are easy to fit in any pot.
tomme boy
12-26-2014, 07:12 PM
Btroj where did you get that scoop at?
btroj
12-26-2014, 07:26 PM
I just got a new one at Walmart. New one is stronger material, previous one was almost a woven mesh and after a few years it fell apart.
Yes! That's what I use. Easy to get, easy to replace, easy to use.
That's 3 of us!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.