lyman 30 Caliber - #311332

[rszkutak]

I'm looking for something for .308 around 175-180 grains and the weight here seem to fit the bill. I am looking for something in a spitzer design that can be used in my Magma MasterCaster.

I will be using this for long range shooting, so I'm looking for this type of bullet.

Has anyone here worked with this bullet before in a .308, how is the accuracy? I'm using foundry alloy lead.

[Blammer]

yep, 308 is good and I like it, it's accurate enough for me out of my AR10

[rszkutak]

Here's what I am looking at, I am shooting long range matches. I'm really growing tired of spending $0.35 per bullet for 175 gr SMK's when I know i can cast a 175's for a lot less than that. I don't need sub sub moa accuracy at 100 yards, but at least 1/2-ish MOA would be great. I can work that from a load perspective though.

ive got an email out with accurate molds asking about a custom cherry. I'd like to see something with a bit longer type of nose like a SMK but in a GC. Do you think it's worth it?

[MT Chambers]

very accurate out of my 1-13 twist .300 Whisper, but needed 1500+fps.

[shredder]

One of my favorites in 30-06. I push them out at 1650 fps. A very acurate boolit for me when I seat them into the lands. I find that helps everything stay straight downbore. The spitzer feeds nicely in my mauser action too.

[Blammer]

since you'll be shooting them a tad slower I would go with a heavier bullet.

perhaps this one
at about 200gr
http://i54.photobucket.com/albums/g81/blammer8mm/Cast%20boolits%20fun/DSCN8443.jpg (http://s54.photobucket.com/user/blammer8mm/media/Cast%20boolits%20fun/DSCN8443.jpg.html)

[Blammer]

this is out of a 30-06 but I suspect it may work out of a 308 also. :)

http://i54.photobucket.com/albums/g81/blammer8mm/Targets/File0153.jpg (http://s54.photobucket.com/user/blammer8mm/media/Targets/File0153.jpg.html)

[L Ross]

1/2 moa ?

[rszkutak]

1/2 moa ?

Yea i'd like to shoot sub 1" groups at 100 yards if possible, or else i will stick with SMK's.

[rszkutak]

Blammer that's a great group! What is your speed????

[rszkutak]

since you'll be shooting them a tad slower I would go with a heavier bullet.

perhaps this one
at about 200gr


That bullet is INSANELY close to what I am looking for! The weight being at 200gr (+/-) is a bit too heavy to properly push out there like I am wanting to do, but at the same token it get's that speed down to around 2250 FPS with Varget on a 38.7gr charge (i use quickload). I'll have to run some ballistic data on this and see how it works over the long haul.

For what it's worth, I'm planning to use the J&M lube from Bayou on all my cast bullets over the coming weeks / months. I'm in the process of converting to this.

96683

[Blammer]

yep the squares are 1/2'' squares so four of them make an inch.

not sure on the velocity, havn't got them over a chrono yet.

standard 22" brl on my Rem 700

run it up quick load real quick see what the vel says.

[Blammer]

my QL crapped out on the newer computer I got, just never got the chance to transfer it over.

[texassako]

I shoot the very similar, but heavier 311334. It shoots MOA or less all day long if I do my part in a 7.62x54r, but at a lot less speed(1300fps) than you are looking for. I have not been able to keep that accuracy at faster speeds yet.

[rszkutak]

my QL crapped out on the newer computer I got, just never got the chance to transfer it over.

are you running an older version that's not windows 7 or win 8 compatible?

Here, I used what you had on your target for a baseline for data. if you want me to drop in other variables let me know, i'd be willing to get more specific if you knew bullet specs for each area, but this as we both know is fairly close.
96701

[BACKTOSHOOTING]

Blammer, What boolit is this and the diamiter ? It looks like the 311365
since you'll be shooting them a tad slower I would go with a heavier bullet.

perhaps this one
at about 200gr
http://i54.photobucket.com/albums/g81/blammer8mm/Cast%20boolits%20fun/DSCN8443.jpg (http://s54.photobucket.com/user/blammer8mm/media/Cast%20boolits%20fun/DSCN8443.jpg.html)

[rszkutak]

I shoot the very similar, but heavier 311334. It shoots MOA or less all day long if I do my part in a 7.62x54r, but at a lot less speed(1300fps) than you are looking for. I have not been able to keep that accuracy at faster speeds yet.

Yea I like speed, I've got a slew of powders here to work with and work up from. I have all of 2013 to develop this load, to be honest I will do whatever it takes to run 175-180 gr 30 caliber cast bullets. In the long run it will save me a ton of money no matter how much i spend now, as a bonus I'm going to prove to the people I shoot with that cast bullets CAN be equal to commercial bullets like SMK's in accuracy. I've got the magma to punch em out, and am in the process of automating the master caster and my star sizer.

we all know they are capable if your right is up to the challenge and you have the know how to do it. I know my rig is up to it without a doubt, it's a FN SPR A1 with a custom brake on a McMillan A1 stock, Timney Trigger, Action Bedding, topped off with a U.S. Optics LR-17 3.2-17 MPR reticle. I've got about $6500-7k wrapped into that weapon.

[Blammer]

are you running an older version that's not windows 7 or win 8 compatible?

Here, I used what you had on your target for a baseline for data. if you want me to drop in other variables let me know, i'd be willing to get more specific if you knew bullet specs for each area, but this as we both know is fairly close.
96701

yea I think I am I have Win 7 and when I went from my old computer, don't know what ver it was. QL wouldn't reload. :(

[Blammer]

Blammer, What boolit is this and the diamiter ? It looks like the 311365

It is the 311365 and that one is sized to .309

[helice]

Like Texassako I have used the 311334 to good effect. But, like Texassako, I couldn't push it. Over 1400'/s and things went south quickly.

[Blammer]

rszk, if you cast it harder, with more of a lino type alloy it will be lighter. You can then up the speed too.

when getting a "spitzer" type nose make sure it has decent nose/bore contact, too much of a pointy nose with no bore riding will product horrible accuracy.

Here is a pic of what you don't want in a cast bullet.
The top one is an 8mm but you get the point, see how it has NO bore riding on the nose and a long pointy nose.

http://i54.photobucket.com/albums/g81/blammer8mm/Cast%20boolits%20fun/DSCN7991.jpg (http://s54.photobucket.com/user/blammer8mm/media/Cast%20boolits%20fun/DSCN7991.jpg.html)

[rszkutak]

rszk, if you cast it harder, with more of a lino type alloy it will be lighter. You can then up the speed too.

when getting a "spitzer" type nose make sure it has decent nose/bore contact, too much of a pointy nose with no bore riding will product horrible accuracy.

Here is a pic of what you don't want in a cast bullet.
The top one is an 8mm but you get the point, see how it has NO bore riding on the nose and a long pointy nose.

http://i54.photobucket.com/albums/g81/blammer8mm/Cast%20boolits%20fun/DSCN7991.jpg (http://s54.photobucket.com/user/blammer8mm/media/Cast%20boolits%20fun/DSCN7991.jpg.html)

I agree you do need a balance between riding the bore and long slender nose. I'm entirely not sure which way I am going to go here on this, it's either take what's out there for say $75 bucks or reinvent the wheel and have one entirely custom cut by NEI from scratch.

[rszkutak]

An idea for a mold to tear up would be an Ideal 311413, heck it would be similar to what I would do in the first place anyway. I'd like to experiment with something similar to what I am going to use in the first place...

then again who knows... UGH!

[Blammer]

if you try to get anything cut by NEI (NOT NOE, two different companies) good luck with the quality control! Since Walt died the quality has really suffered.

I tried to get a few group buys through them, the quality of the moulds I received really sucked, I had to send them back two or three times! The whole batch of moulds. I'll never deal with them again.

[rszkutak]

if you try to get anything cut by NEI (NOT NOE, two different companies) good luck with the quality control! Since Walt died the quality has really suffered.

I tried to get a few group buys through them, the quality of the moulds I received really sucked, I had to send them back two or three times! The whole batch of moulds. I'll never deal with them again.

I've noticed that, I hate the idea of dealing with NEI but they are about the only place that I can go to for a truly custom mold for a Magma. No one else really wants to cut one.

[bhn22]

Won't Magma convert a mold for you? I thought they offered that service. I'd look long and hard at SAECO molds too. If you find a design you like, the quality is excellent, and the molds are all steel. Do Master Caster molds need to be steel?

[rszkutak]

Won't Magma convert a mold for you? I thought they offered that service. I'd look long and hard at SAECO molds too. If you find a design you like, the quality is excellent, and the molds are all steel. Do Master Caster molds need to be steel?

magma would convert molds but they have limits. Yea the magma molds have to be steel, the clammering of the machine will wear out an aluminum mold much quicker than a steel. The steel molds just last forever.

The worst part here is that Saeco doesn't offer anything for what I am looking for. Like in Blammer's example up top i want something similar to the 8mm, but with decent contact... ughhhhh

It's possible that the lyman 311322 is as close to what I want, but in a stock mold.

[bhn22]

I see what you mean. Did you look at RCBS too? I've heard good things about their 30 cal silhouette bullets, the only real issue appears to be that they would likely have a low BC.

BTW, thanks for the info on molds for the Magma.

[frnkeore]

The 323366 isn't a inherintly inaccurate bullet if you have the right throating for it or if you shoot it breech seated.

These are pictures of load devolopement I'm doing with it in a 32/40 match rifle. This bullet is cast of soft 20/1 lead/tin alloy. The first picture is before I took the GC off (can't use them in my type of matches) and the next two are with the PB at .2 tenth, 4227 increments. All are 100 yard groups.

Also, SOME people say that you can't get good accuracy with a bullet that has a scraper groove. All the bullets we are talking about, except the 311365 NOE have scraper grooves.

A bullet that is close to the 323366, and has the same basic design, is the 311329.

Frank
976699767097671

[frnkeore]

The 323366 and the 311329

97672
97673

[winelover]

yep, 308 is good and I like it, it's accurate enough for me out of my AR10

What kind of accuracy are you getting in your AR-10? I've been working with mine, with various boolets, and not getting where I like to be.

I tried the NOE 311365, suggested in a later post, with dismal results. I used both Varget and 5744. By the time I reached the level where the action would cycle (29.0 for Varget, 25.0 for 5744), groups @ 60 yards were opening up to 4" or better!

Best grouping boolet, so far has been the RCBS 165 Sil., with Varget @ 1" C-C.

Winelover

[Blammer]

varget has not worked for me, my powder of choice for me is IMR4895.

for me 8x11 at 100yds standing with open sights is what my accuracy is.(meaning the entire mag of 25 will land on that piece of paper) Never really sat down to see how good it really is. I suspect 2-3" at 100yds.

[Larry Gibson]

"SOME" people don't say cast bullets with scraper grooves can't be shot accurately. What "SOME"people said was is cast bullets with scraper grooves are to be shot as MKs are in the .308W (as the OP says he wants to) then the scraper groove is a weak point. The much better design for the OP's needs would be the MP311-180.

Larry Gibson

[frnkeore]

larry,
You did say the the 311332 was distorting (caused by the scraper) when shot in a 308 Win at about 1600 fps.

The OP is looking for input from people that had experiance with the 311332, there were many postive responces.

Frank

[Larry Gibson]

No frank, I did not say the OPs 311332 was distorting. I mentioned it as a potential problem depending on alloy and velocity. What is distorted is your interpretation of what I posted. I corrected your misinterpretation in that thread. While I do appreciate your continual attention wouldn't it be better to stick to facts?

Larry Gibson

[frnkeore]

Well lary,
This IS exactly what you said about the 311332 scaper groove. Underlining is mine.

"The exact same thing will/is happen(ing) to the OP's 311332 cast bullets."

Are you deigning that?

Frank

[Larry Gibson]

And it possibly was frank, just as I stated in my original post in that thread.....like most "potential" solutions to problems posted here it was a suggestion of something to consider. I did not cast, load or shoot the bullets in the OPs rifle, neither did you. Anything either of us profer is simply an opinion on what might be the problem. What we suggest may or may not be fact. There is no way either of us is going to prove it one way or the other isthere? frank...........you really need to give it a rest. Why don't you just put me on "ignore" and save yourself a lot of heartburn trying to continually prove me wrong on any and every inconsequental point.

Larry Gibson

[L Ross]

What I'd really be interested in is seeing whether the collective wisdom of the most experienced casters on this forum believe the OP's original question is even remotely possible.
If I have misinterpreted his meaning I hope he corrects me. I understood him to ask this group, is it feasible/possible to create a cast bullet, using a Magma Master Caster, to replicate the results he is currently getting by shooting 175 gr. Sierra Match Kings in a highly accurate custom bolt action .308 for shooting long range? Furthermore his idea of accuracy was stated as hopefully 1/2 moa.
I have personally witnessed cast bullets being used to shoot some very small groups at ASSRA/ISSA matches where the individually hand cast, weighed and pampered bullets were loving breech seated into fine single shot rifles. The single case being carefully oriented into the chamber each time. These groups were shot at 200 yards. I got the feeling the OP was more likely talking 600 yards and wanted to mass produce his bullets. So am I nuts to think his goal is futile?

Duke

[cbrick]

Just so folks reading this thread can see the difference in the boolits discussed.

Left > NOE 311284
Center > Lyman 311332
Right > NOE 311365

98034 98030 98035

Rick

[cbrick]

I got the feeling the OP was more likely talking 600 yards and wanted to mass produce his bullets. So am I nuts to think his goal is futile? Duke

I'll agree that it sounds like a lofty goal but possibly not futile. For many of us a good deal of the fun is in the journey.

Rick

[frnkeore]

And it possibly was frank, just as I stated in my original post in that thread.....like most "potential" solutions to problems posted here it was a suggestion of something to consider. I did not cast, load or shoot the bullets in the OPs rifle, neither did you. Anything either of us profer is simply an opinion on what might be the problem. What we suggest may or may not be fact. There is no way either of us is going to prove it one way or the other isthere? frank...........you really need to give it a rest. Why don't you just put me on "ignore" and save yourself a lot of heartburn trying to continually prove me wrong on any and every inconsequental point.

Larry Gibson

A quick little reply lary and then I am acually done with it!

You didn't say possibly you said IS (as I underlined) and the evidence said otherwise.

Frank

[frnkeore]

Rick,
Thoughs pictures make a good point. They all have scrapers. I own and have shot the NOE 340365 and I also (mainly) shoot tapered match bullet that are very much like scraper groove bullets, in that the first groove is supported by less than half the diameter of the groove diameter of the barrel. The picture is a 200 yard group that I shot with the the NOE bullet that measures 1.990". There is only 3/4" verticle in this group.

Frank

98042

[Larry Gibson]

Like Texassako I have used the 311334 to good effect. But, like Texassako, I couldn't push it. Over 1400'/s and things went south quickly.

I wonder why? Could it be that long unsupported nose with the scraper groove under it? The OP "like's speed" and mentions 2250 fps with it wanting moa or less accuracy out of his FN rifle "knocking them out" on an automated casting machine and automated sizing & lubing. Anyone want to bet he'll succeed......perhaps frank........?

Larry Gibson

[Blammer]

are you running an older version that's not windows 7 or win 8 compatible?

Here, I used what you had on your target for a baseline for data. if you want me to drop in other variables let me know, i'd be willing to get more specific if you knew bullet specs for each area, but this as we both know is fairly close.
96701

Yea, close enough!

2100fps, and if I could crank them out in a master caster water dropped, that would be the cats meow!
I'd have to get a full auto bolt gun! :)

[45 2.1]

Yea i'd like to shoot sub 1" groups at 100 yards if possible, or else i will stick with SMK's.

What you want to do is entirely possible, just not the way you're going at it. An AR-10 will shoot cast MOA and under at 2,400 fps IF you load it correctly with the right boolit. That boolit is the MiHec 30 Silhouette. Unfortunately for you it doesn't come in a steel mold, just brass.


I wonder why? Could it be that long unsupported nose with the scraper groove under it? The OP "like's speed" and mentions 2250 fps with it wanting moa or less accuracy out of his FN rifle "knocking them out" on an automated casting machine and automated sizing & lubing. Anyone want to bet he'll succeed......Larry Gibson

More like it doesn't fit from being undersize on the nose and it tips out of line when it gets booted in the behind from a load with a little too much pressure. That, BTW, is the cause of some of your testing failures. Get the boolit started straight, concentric with the bore, and good things happen. As far as automated equipment, IF it is set up properly (an automated sizing and lubing with a GC boolit is something I have to see though) and the test platform is suitable and the boolit fits.... then it can work. Just like any other rifle provided the operator makes wise decisions and doesn't blame something else for their lack of attention to detail.

[yondering]

OP, have you considered powder coating your cast bullets? That will eliminate the velocity restrictions of cast bullets, to some extent. I think what you're looking for is possible with a powder coated boolit.

I'm running an old H&G #20 (which I've read is similar to Lyman's #311413), which casts 170gr from coww. I'm powder coating it, then applying the gas check and sizing. I'm pushing this one with full power loads of IMR 4895 (42.5gr iirc) in my 308 PTR91, and getting about 2" @ 100 yards. That's about the best this rifle shoots with jacketed bullets too, so I think better accuracy is possible from a better rifle.

Sorry I don't have a better picture, it's the dark green bullets on the lower right, and one of the light green bullets on the upper left. At the upper right is a recovered bullet that was fired subsonic through some wood.
http://i24.photobucket.com/albums/c26/zthang43/Bang/molds/IMG_2303.jpg

[Larry Gibson]

Amazing how one knows of my "testing failures" considering you refuse to shoot with me to see. You probably would like to bring up the 311291 again but considering what bass and I both did with it you've already lost on that one. Also I see no members substantiating your 2400+ fps accuracy claims with an AR10. Perhaps they or you would post some pictures of 10 shot 100 yard groups? I also noticed no comments from you on my posted 100, 200 & 300 yard 10 shot groups I posted at 2600 fps.......Perhaps the "failure" you refer to?

Oh, or perhaps the "failure" you refer to is indeed caused by the weak point in many older designs. ...the scraper groove. ....

Larry Gibson

[45 2.1]

One cartridge, one rifle, one boolit wonder theories don't make reality or prove much, just what that combination did, with all the tolerance stack involved. Did you have witnesses for what all you posted since you asked, we've never heard from them either..... I did, and shot from semi-auto's no less...... As far as boolit faults are concerned, talking to an engineer doesn't mean much as they gave you the answer you could understand.... a couple of years in TAM classes and you'll understand what you don't now.

[Larry Gibson]

Yes I have witnesses and have offered numerous times to you and several other nay sayers here to shoot with you anytime. Any members around Lake Havasu City AZ just give me a PM and we'll go shooting; out in the desert or on the 100 - 300 yard range at Sara park. Conversely though I have to ask why it is that you, 45 2.1 and the other nay sayers, adamantly refuse to shoot with not only me but numerous other members of this forum?

Why talk with an engineer? Because frank didn't understand how the scraper groove was a weak point of the bullet; a smaller diameter rod does not have the strength of a larger diameter rod of the same material and will bend or collapse under less pressure. The engineer could tell you scientifically how the smaller column at the center of the scraper groove can not withstand the stress (created by the acceleration G force) that it could if of equal diameter to the nose and tapering to the diameter of the front drive band. He could also explain to frank how the lube grooves are supported by the lube during acceleration if frank didn't understand that fluids compress very little which is the basics of hydraulics. It would take about 5 - 15 minutes to explain in layman terms. frank ask the question and I suppose I could have suggested 2 years of TAMS study like you did but that's a little bit of a ridiculous way to give a simple straight forward answer isn't it?

So, 45 2.1, if you know anyone on the forum out this way that would like to see the verification and even shoot a few groups themselves they are more than welcome to contact me so we can go shooting. I will also show them the structural faults of scraper grooves with numerous bullets in numerous rifles of various twists.

One last question; you know *** (unmentionable former member) sold me his MP 311-180 that I believe you designed(?). Why no scraper groove on that bullet if you designed it for the .308W for use in ARs? BTW; if you did design that bullet it is an excellent design. The design follows the guide lines I have mentioned in numerous threads & post for a HV cast bullet. Note the commercial moulds of similar design from .224 upwards of 8mm or .35 caliber do very well pushing the RPM threshold to higher levels. One reason being the elimination of the scraper groove adds to the strength of the bullet lessoning imbalances from occurring during acceleration.


Larry Gibson

[frnkeore]

lary,
You can say anything you want about scraper grooves but, until you can show that they actually fail, you have no credibility. All that you talk about is assumption. As the Lil ol' lady say's....... "Show me the beef" :)

I've posted a picture of a 200 yard group that I shot with a full spitzer, scraper groove bullet that did well w/o deformation. I also have asked for the name and number of the "engineer" that suppositely told you that land supported bullets will bend or distort.

Where is your "Beef" ?

Frank

[TheCelt]

I've been a member here for a few years and lurked quite a bit for a few before joining. What I love about this group was the vastness of the knowledge here and how freely it was given. I can honestly say that I've learned as much in the last two years here as I did in the 40 casting years before.

There are a LOT of folks here with a LOT of knowledge and experience. As is usually the case with those folks they don't always agree. That's OK as the discussions between them are always interesting and sometimes educational.

It does get distressing when people we have followed and have regard for start going at it on points they can't agree on. If you don't mind me saying so I reckon Ya'll be a darn site happier if you'd read what ya wrote before ya send it and ask yourself how you'd feel if someone spoke to you that way. All of you are deserving of the respect of those that learn from you............and each other.

[Just Duke]

Lets all help each other. Were all friends right? Some here spend more time than with there wifey so lets all be buds. :)

[Larry Gibson]

What I'd really be interested in is seeing whether the collective wisdom of the most experienced casters on this forum believe the OP's original question is even remotely possible.
If I have misinterpreted his meaning I hope he corrects me. I understood him to ask this group, is it feasible/possible to create a cast bullet, using a Magma Master Caster, to replicate the results he is currently getting by shooting 175 gr. Sierra Match Kings in a highly accurate custom bolt action .308 for shooting long range? Furthermore his idea of accuracy was stated as hopefully 1/2 moa.
I have personally witnessed cast bullets being used to shoot some very small groups at ASSRA/ISSA matches where the individually hand cast, weighed and pampered bullets were loving breech seated into fine single shot rifles. The single case being carefully oriented into the chamber each time. These groups were shot at 200 yards. I got the feeling the OP was more likely talking 600 yards and wanted to mass produce his bullets. So am I nuts to think his goal is futile?

Duke

Duke

No, you are not "nuts". You are correct, especially if the OP wants to use a design such as the 311332. Some here have missed the point of the OP's question. You have summerized it nicely.

And as mentioned there is no need for anyone to get raspy about it. I have mentioned numerous times I would be glad to shoot with any of them and demonstrate the problems associated with shooting cast bullets at HV in faster twist rifles. I also would be glad to discuss the design charactoristics of the bullets that perform well at HV/high acceleration. I would also denonstrate the success at shooting cast bullets at HV in such rifles. The offer is always open.

On page 78 of Lyman's CBH #4 we see a listing of selected loads for the 30 BR from CBA benchrest matches. The bullet moulds are listed. A couple observations are noteworthy to this discussion; none of the bullets used have a scraper groove. The bullets used in the velocity range of 2400 - 2794 fps were light in weight, had short noses, long % of bullet length bearing surface and were shot in very slow twists (1:17 or 1:18"). Perhaps there is something to be learned there?

Larry Gibson

[rszkutak]

Sorry for the lack of response lately, I've been working in my yard and redoing it getting ready for summer... then we deicded on Saturday morning to get a 8 week old puppy. Needless to say I've been busy.

basically you are all on the right path here, I am looking for what appears to be unicorn tears. My rifle is cold bore accurate and with SMK's or Nosler 175's shoots sub moa all day long at any range.

I love the design of the NOE 311365, it's ideal for what I am looking to do to be honest. that having been said I guess I'm changing my mind over the concept and now looking towards a truly custom gas check maker from Freechex if he can make one for me and a cherry mold where I will buy the cherry as well. I think I am going to duplicate every detail of a Nosler 175 Custom Competition with gas check and have the custom gas check maker make them to wrap over the boatail.

Possible, yes, but will I be able to get the mold cutter and Freechex to make the gas check is still being debated? I'm sure i'd have to have the bullet itself cast and send it out to him to duplicate the dimensions on. Of course the bullet will have no lube grooves as I will use J&M lube.

Copying it bit by bit should yield very similar results to the actual bullet but for a fraction of the cost. The bullet itself will have to be dimensionally changed slightly as the density of the lead alloy will be slightly different weight than the pure lead they run in FMJ's.

SO tell me I'm nuts here folks, or am i possibly onto something here???

Yes I will automate every aspect of production except for the freaking gas check / sizing aspect. I'm not sure how / if at all possible that automating that process is, so it's manual for me just for that.

[TheCelt]

Well Sir, I wouldn't say you're nuts but I do figure you've got quite a hill to climb. I'll dime myself out here and say I have NEVER shot a cast sub MOA group with ANY cast Boolit. I figure there's those that have cause I've read about them and I sure keep trying. My improvements are incremental as I test different lubes/alloys/powders/primer/filler /seating depth/sizing diameters etc. etc. etc. and all the combinations therein. Right now I'm testing with an older mold I have, the 311413, in both solid and HP configuration. I am getting 1.5 MOA from a 1-10 308 at 2100 FPS (with the solid) which is very exciting to me. It too is a sub-MOA rifle with 168gr SMKs (.358" @ 100yds for 5 rounds). The 311413 looks like the lime green Boolits in post #46 but with a longer GS shank and a bit shorter lower drive band.

You may want to do a search for boat tail gas checks here as I recall somebody developing them a bit over a year ago. Haven't heard much lately but there may be a thread for you to review.

I wish you the best of luck in your endeavors Sir. a LOT of good info here and a LOT of experience. You sure came to the right place to get started!!!

[rszkutak]

Yes i have come to the right place, I've been on the board for years more or less as a lurker and never really adding much or responding to many posts. As you can tell from my join date in 2008, i've been on here for 6 years but never posted much.

I will have to look for that post, I know the info is out here ya just gotta find it!

[texassako]

I don't know if you have found it already, but this is about the most comprehensive boat tail gas check test I have seen: http://castboolits.gunloads.com/showthread.php?185954-BOAT-TAILED-Gas-Check-Update-Teaser&highlight=boattail

[TheCelt]

That's it!

[rszkutak]

AWESOME that's a great thread, I'm subscribed to it... hope to gain some awesome info there.