View Full Version : MiHec 2 or 4 cavity brass 358640 380 ACP/ 9mm Luger & Makarov Cramer HPGC or PB
45 2.1
01-13-2013, 11:37 AM
MiHec 2 or 4 cavity brass 358640 380 ACP/9mm Luger & Makarov Cramer HP GC or PB
This GB is Closed.....
This is a new design in this weight series. This will be a two or four cavity, Cramer brass HP mold. It will cast at 0.358" or just slightly over for the 380 ACP and 9mm Luger……… and 0.366” for the 9mm Makarov. Gas check and plain base versions will be available for both, but the 9mm Makarov GC version will probably have to use either home made GC or 375 GCs. How the makarov GC works out is really up to the buyer since it is a special size Edit... Gator is offering 9.3 GCs now. The internal base diameter is the same as the 375 which is about 0.004" larger than the GC shank diameter. These may or may not work. that is not offered with no guarantee of fit. Dependent on what MiHec orders for cherries, these molds might be cut with one cherry and bored and orbited for different options, his choice on that.
Edit: For those of you wondering about it's use in the 357 Sig, here are the parameters.
If you seat the GC version to the base of the neck, 0.035" of the front band shows and the cartridge is under the spec length of the cartridge. If you seat the front band to the end of the case, about half of the GC surface is in the case with no lead exposed. Either way it looks to work out.
We will need fifteen to commit to this. We will run this until we get the number we need or until MiHec closes the GB.... and there is no selected date that will happen.
For the two cavity mold, the price is $85 with one set of pins included plus $8 per extra pin set if wanted plus $15 shipping.
For the four cavity mold, the price is $120 with one set of pins included plus $16 per extra pin set if wanted plus $20 shipping.
If the HP pins are not suitable for reversal to a solid, the blank pins come with the price of the mold. If you do not want the HP pin sticking out of the base of the mold, in the case of reversable pins, you can order a set of blank pins for a smooth mold bottom.
Pin options: 1) large HP, 2) penta HP, 3) blank pin for flat nose
Please list your Forum name and your disguised e-mail address in suitable form and the pin options you think you want along with the number of molds.
Here is a sign-up list:
1. FLYCUTTER.....r underscore kark AT ATT dot net..... One 4 cavity 0.358" plain base mold with large and penta pins & One 4 cavity 0.366" plain base mold with large and penta pins
2. Crosbyman.....trimmATtbjonesllcDOTcom.....One 4 cavity 0.358" plain base mold with penta pins
3. pomofo.....pmfoss [at] gmail {dot} com. .....One 4 cavity 0.366" plain base mold with large pins
4. autodidact.....jbpaul (at) suddenlink (dot) net.....One 4 cavity 0.358" plain base mold with all pins
5. harley45.....Eric at white tiger blog dot com..... One two cavity 0.358" plain base mold with all pins
6. forcedconvection.....rg7slinger at gmail dot com.....One 4 cavity 0.358" plain base mold with large and penta HP pins
7. fixit156.....Fixit156AThotmailDOTcom.....One 4 cavity 0.358" gas check mold with large pins
8. rcwarship.....rcwarship at comcast dot net.....One 4 cavity 0.358" plain base mold with large and penta HP pins
9. cja245.....cja245 at gmail dot com.....One 4 cavity 0.358" plain base mold with large and penta HP pins
10. CPL Lou.....louiestanfield (at) gmail (dot) com.....One 2 cavity 0.358" gas check mold with all pins
11. jimgun.....jgruver2013 at gmail dot com......One 4 cavity 0.358" gas check mold with all pins
12. Hamish.....popeye91 ar frontier dot com.....One 2 cavity 0.358" plain base mold with large and penta HP pins
13. sparkz.....Sparkz1000 AT GmAiL Dot Com-awn.....One 2 cavity 0.358" gas check mold with all pins
14. timberhawk.....grbusby at tx dot rr dot com.....One 4 cavity 0.358" plain base mold with all pins
15. Ruger480.....cazzoo at comcast dot net .....One 2 cavity 0.358" plain base mold with large HP pins
16. Buzz64.....buzz at joniypc dot com.....One 4 cavity 0.358" plain base mold with all pins
17. dogman.....mlmaher at gmail dot com......One 4 cavity 0.358" gas check mold with large HP pins
18. 44 mag nut.....magnut44 at gmail dot com.....One 4 cavity 0.358" plain base mold with large HP and blank pins
19. alha.....snowserver (at) hotmail d0t com .....One 4 cavity 0.358" gas check mold with all pins and One 4 cavity 0.366" gas check mold with all pins
20. lup.....rstaab (at) Panix dot com.....One 4 cavity 0.358" plain base mold with all pins
21. Darkh2odiver.....darkh2odiver (at) hotmail [dot] {com}.....One 2 cavity 0.358" plain base mold with 2 sets of large HP pins
22. TMSCU.....tmoyer1952 at yahoo dot com.....One 4 cavity 0.358" gas check mold with all pins
23. funshooter.....weldinspector at earthlink dot net.....One 4 cavity 0.358" plain base mold with all pins
24. gtgeorge.....gspatton at gttransmissions dot com.....One 4 cavity 0.358" plain base mold with all pins
25. jeremiah.allen1.....jeremiah (dot) allen 1553 (at) gmail (dot) com.....One ? cavity 0.358" plain base mold with all pins
26. sergraf.....sergio underscore rafanan at yahoo dot com.....One 4 cavity 0.358" plain base mold with all pins and one set of handles
27. redneckdan.....dmhamilt (at) mtu (dot) edu.....One 2 cavity 0.358" plain base mold with penta pins
28. BMKoenig.....rommelbmk (at) comcast (dot) net.....One 4 cavity 0.358" gas check mold with all pins and One set of handles
29. tiger762.....kef762 AT yahoo com.....One 4 cavity 0.358" plain base mold with all pins
30. Rymark223.....sbmathews74 at gmail dot com.....One 4 cavity 0.358" gas check mold with large and penta HP pins and One 4 cavity 0.366" gas check mold with large and penta HP pins
31. dkf.....krflff2 (at) dejazzd (dot) com.....One 4 cavity 0.358" plain base mold with all pins
32. huntnfish72.....Billyv3 at newnorth dot net.....One 4 cavity 0.358" plain base mold with all pins
33. jwfox....jay dubya fox nine four eight zero AT America On Line dot com.....One 4 cavity 0.358" plain base mold with both large, penta pins and blank pins and One set of handles
34. SP5315.....wmclark AT email DOT com.....One 4 cavity 0.358" gas check mold with all pins and One 4 cavity 0.358" plain base mold with all pins
35. doctorggg.....gggmmg at verizon dot net .....One 4 cavity 0.358" plain base mold with all pins
36. Bruzier.....b dot rolfe1 at bellaliant dot net.....One 4 cavity 0.358" gas check mold with large and penta HP pins
37. kayak1.....jason at kates (dot) [org].....One 4 cavity 0.358" plain base mold with all pins and One set of handles
38. Skew.....edotson123 (at) tx (dot) rr (dot) com.....One 4 cavity 0.358" plain base mold with all pins
39. dieselrealtor.....doug at realtorsink dot com.....One 2 cavity 0.358" plain base mold with all pins
40. Ironwood.....ironwood of evergreen at yahoo dot com.....One 4 cavity .358" gas check mold with all pins
41. Bluestraw.....Bluestraw at a o l (d o t) c o m.....One 4 cavity 0.358" gas check mold with all pins
42. SethD.....seth doty 44 4 at hot mai l dot com.....One 4 cavity 0.358" gas check mold with large and blank pins
43. TMSCU.....tmoyer1952at yahoo dot com.....One 4 cavity 0.358" gas check mold with large and penta pins
44. Virginia John.....jwstuartjr at hotmail dot com.....One 4 cavity 0.366" plain base mold with all pins
45. eezz.....eezz at g mail dot com.....One 4 cavity 0.358" gas check mold with all pins and One 4 cavity 0.366" plain base mold with penta pins and Two sets of handles
46. oldsingleshots.....haletree at att dot net.....One 2 cavity .358" gas check mold with all pins and One set of handles
47. tygar.....tbrolliniATgciDOTnet.....One 2 cavity 0.358" plain base mold with small HP and blank pins
48. Aaron.....5090shiloh at gmaildotcom.....One 4 cavity 0.358" plain base mold with all pins
49. chprplt.....exit 13 five at aol dot com.....One 4 cavity 0.358" plain base mold with all pins
50. AZBrian.....sellsell(at)cox(d0t)net.....One 4 cavity 0.358" plain base mold with all pins & One 4 cavity 0.358" gas check mold with all pins
51. atom73.....neilsbohr73@ yahoo. you know what.....One 2 cavity .358" plain base mold with large pins and One set of handles
52. castblast.....sthwld64atgmaildotcom.....One 4 cavity 0.358" plain base mold with all pins
53. mpbarry1.....mpbarry1 at gmail dot com.....One 4 cavity 0.358" plain base mold with all pins
54. hicard.....hicard21atoutlookdotcom.....One 2 cavity 0.358" plain base mold with large pins
55. rnelson11.....rnelson11 at chesnet dot net.....One 4 cavity 0.358" gas check mold with all pins
56. Sgt Petro.....aaronpetroski at gmail dot com.....One 2 cavity 0.366" plain base mold with all pins
57. maderawood6.....maderawood6 at geemail dot com.....One 4 cavity 0.358" plain base mold with all pins
58. ballistim.....ballistim(at)yahoo(dot)com.....One 4 cavity .366" plain base mold with penta pins
59. tiger762.....kef762 AT yahooDOTcom.....One 4 cavity 0.358" plain base mold with large pins
60. taugust.....g99jeb at aol dot com.....One 4 cavity 0.358" plain base mold with penta and blank pins
61. HillBilly2.....ffrisby AT hot mail dot com.....One 4 cavity 0.358" plain base mold with penta and blank pins
62. J & D Armament.....Jdarmament at gmail dot com.....One 4 cavity 0.358" plain base mold with penta pins
63. double00.....jcgraeler at gmail dot com.....One 4 cavity 0.358" plain base mold with all pins
64. tja6435.....Tja6435 at gmaildotcom.....One 4 cavity 0.358" plain base mold with large and penta pins
65. silverjay.....Silverjay7 at gmail dot com.....One 4 cavity 0.358" plain base mold with large pins
66. dragon813gt.....dragon813gt at yahoo dot com.....One 4 cavity 0.358" plain base mold with all pins
67. 45 2.1.....One 4 cavity 0.358" plain base mold with all pins
68. 45 2.1.....One 2 cavity 0.366" plain base mold with all pins
69. 45 2.1.....One 2 cavity 0.358" gas check mold with all pins
70. vbmax.....vbmaxATcox.net.....One 4 cavity 0.358" plain base mold with large and blank pins
FLYCUTTER
01-13-2013, 12:33 PM
Can this mold be made without the gas check ?
45 2.1
01-13-2013, 12:49 PM
Can this mold be made without the gas check ?
I've seen a couple of GBs where MiHec used a GC cherry and bored out the shank to PB........ so yes, its possible IF he would do it.
chrisw
01-13-2013, 11:27 PM
cute little one, bet she wants to go FAST! (1400+)
I think a GC is needed for this one if its pushed that hard!
FLYCUTTER
01-14-2013, 12:05 PM
FLYCUTTER r underscore kark AT ATT dot net 4 cavity, option 1 & 2, without gas check design, 1 mold.
For a .380 bullet the speed will be under 1000 fps.
Crosbyman
01-14-2013, 12:21 PM
I am in for a 4 cavity with extra pins.
Crosbyman
45 2.1
01-14-2013, 02:40 PM
For a .380 bullet the speed will be under 1000 fps.
Yes, it probably will be in the shorter lighter blowback designs. There are several very stout 380 / 9mm Kurtz handguns out there that will eat the lighter guns lunch. You will get leading with hot soft boolit loads in some of them if you want the HP to expand well....... thus the GC design.
Down South
01-26-2013, 11:15 PM
You got me again. This place is getting expensive. Found this doing research for another member.
Put me down for a 4-cavity GC, Lg HP Pins.
swactor at ymail dot com
Low Budget Shooter
02-01-2013, 01:23 PM
45 2.1, it would help me to know for sure sooner rather than later whether or not plain base is an option here. Could you find out from The Man? If that is an option, please sign me up for 4 cavity large HP and penta HP. Thanks, LBS jeff dott richard dott young attt geemale daught comm
Down South
02-01-2013, 01:49 PM
Good time of the year to cast a bunch of these up. My 9's are getting hungry.
harley45
02-01-2013, 05:59 PM
I'm in if we can get it without a gas check
Lonegun1894
02-05-2013, 09:39 PM
Please sign me up for the 2 cavity HP list. If this gets split into a GC and non-GC option, I want the GCd version also. Lonegun1894 at yahoo dot com. Thanks.
FLYCUTTER
02-05-2013, 11:49 PM
I'm not trying to hijack this thread but my question to Mihec is .. Could he run the 9mm Makarov mold with this one like he did 3 years ago with the .380 ????
45 2.1
02-06-2013, 09:45 AM
I'm not trying to hijack this thread but my question to Mihec is .. Could he run the 9mm Makarov mold with this one like he did 3 years ago with the .380 ????
Yes, he could........ AND i'm going to change this thread shortly to reflect the changes wanted above.
fixit156
02-06-2013, 02:09 PM
Put me down for a 4-cavity GC, Lg HP
Fixit156at hotmail dot com.
Gun-adian
02-06-2013, 09:38 PM
Finally a design that just might work in the short necked 9x25 Dillon. This beast will launch a 90 gr. J-word at almost 2000 FPS so the gas check will defs be required.
I'm in for a 4 cavity gas check with all the pins.
Thanks.
Mike.
45 2.1
02-07-2013, 11:13 AM
OK folks........ the choices have been changed to what you've wanted. If you want to change, either edit or repost.
FLYCUTTER
02-07-2013, 05:21 PM
Thank you 45 2.1 for making this change to accommodate all of us on this buy and a thank you to Mihec also.
Put me down for 1 mold, 4 cavity, HP and pinta pins, PB .358"
Also 1 mold, 4 cavity, HP and pinta pins, PB .366"
This is my revision to the previous request
45 2.1
02-08-2013, 05:39 PM
Everybody that has already posted please look at the list to see if anything from you is needed.
Thread updated.
Gun-adian
02-08-2013, 05:59 PM
Email addy as requested.....
jumpgate at telus dot net
Thanks.
Mike.
FLYCUTTER
02-09-2013, 12:26 PM
correction on the e-mail address. r underscore kark AT ATT dot net
Lonegun1894
02-11-2013, 07:24 PM
Since I need to decide on weather I want the large HP pins or the penta HP pins, could someone give me a very brief idea of advantages or disadvantages of both so I can make an informed decision? I bet I should probably know this already, but unfortunately have to admit I dont. And the intent is to use it as a back up gun for defensive use, not paper or hunting anything. Thanks for any and all help.
chrisw
02-12-2013, 12:57 AM
in a nutshell, Penta might/ should fragment ( with harder lead alloy). Occasionally with less brittle alloy it mushrooms "easier" in sections (like a Barnes or a flower rather than a mushroom...)
Perhaps other smarter people can tell you how this particular bullet will do?
I don't know enough about this bullet nor your gun to say what's "best" for you, but personnally I'd probably try both!
Since I need to decide on weather I want the large HP pins or the penta HP pins, could someone give me a very brief idea of advantages or disadvantages of both so I can make an informed decision? I bet I should probably know this already, but unfortunately have to admit I dont. And the intent is to use it as a back up gun for defensive use, not paper or hunting anything. Thanks for any and all help.
Lonegun1894
02-12-2013, 01:13 AM
So if I understand you correctly, the penta pin should fragment or expand more readily, while the standard HP should still mushroom, but not as much, and therefore provide slightly less expansion while also giving better penetration? If this is correct, then considering that my guns are a Russian Makarov with the .380 ACP barrel and a Bersa .380, and not one of the super strong .380s or 9x19s or anything capable of higher velocity, and to be frank, me having limited faith in the .380s ability to penetrate to begin with, I would probably be better off with the standard HP over the penta HP. Or do I have my head screwed on backwards with this?
45 2.1
02-12-2013, 10:01 AM
I'd probably be better off with the standard HP over the penta HP. Or do I have my head screwed on backwards with this?
The penta pins outer points are the same nominal diameter as the large HP..... little difference in initiation of expansion, just the manner of expansion is changed. Most of the problem with high performance 380 ammo is lack of expansion. Either of your guns are big enough to do what the cartridges are capable of.
harley45
02-14-2013, 10:36 PM
4 cavity non gas check regular hp pins
Eric at white tiger blog dot com
cja245
02-14-2013, 11:42 PM
I'll take a 4 cavity .366" HP (non gas check) with the large and penta pins .
cja245 at gmail dot com
Thanks
timberhawk
03-05-2013, 08:38 PM
I want to get in on this GB, but have a question. This boolit in 9mm will be a screamer, especially the hollow point version.
I have an order in for a PB Checkmaker, but it hasn't been delivered and I haven't played with it.
The question is will a PB Check made of .006 aluminum (Miller Lite screw top aluminum cans) let me push this boolit with full power 9mm loads, or do I need to just get the GC version.
FLYCUTTER
03-06-2013, 12:29 AM
In my humble opinion I would use gas checks for magnum pistol and rifle bullets. I see you are set on a gas check bullet and I personally would go with a bullet designed for a check, not smashing something .006 oversize and deforming the lead on a light hollow point bullet. I also would use a softer alloy,(under 15 bn.)
so the hp would upset rather than blow apart. Good luck on your choice.
Lonegun1894
03-13-2013, 12:13 PM
Could I please back out of this GB? Had a couple things pop up that need to get done and if I manage to get the funds together before this closes, I will get back in, but for now, unfortunately have to assume I won't so don't want y'all counting on me unless I get the funds in hand and ready to send.
forcedconvection
03-13-2013, 02:15 PM
I would like one 4 cavity 0.358" plain base mold with large and penta pins.
rg7slinger at gmail dot com
Thanks,
Ryan
CPL Lou
03-14-2013, 04:06 AM
Please sign me up for a 2 cavity, .358, GASCHECK, and all 3 pins. :D
louiestanfield (at) gmail (dot) com
THANKS !
pomofo
03-20-2013, 11:49 PM
Please put me down for a 4-cavity plain base .366" with large HP pins. pmfoss [at] gmail {dot} com.
jimgun
03-30-2013, 06:19 PM
4 cavity gas check .358 with all pins....... jimgun..........jgruver2013 at gmail dot com....... thanks jim
Down South
03-30-2013, 11:47 PM
Guys, sorry but due to unforeseen circumstances, I have to back out on this GB.
Hamish
03-31-2013, 12:36 AM
Here we go again,,,,
Hamish 2C PB deep pins, penta pins popeye91 ar frontier dot com
45 2.1
03-31-2013, 09:23 AM
Hamish 2C PB deep pins, penta pins
Rich, I put you down for a 0.358" mold since you didn't specify which. If its the other say something.
Thread updated............
FatMcNasty
04-08-2013, 01:39 PM
Id like in on the GB I need,
One 4 cavity .358 Plain Base all Pins
One 4 cavity .366 Plain Base Penta Pins
Thanks,
fatmcnasty at hotmail dot com
timberhawk
04-09-2013, 02:01 PM
Put me down for a 4 cavity .358 plain base with all pens.
grbusby at tx dot rr dot com
Ruger480
04-11-2013, 01:18 AM
4 cavity brass 358640 380 ACP plain base and W/HP and a set of blank pins please. cazzoo at comcast dot net
Thank you
45 2.1
04-12-2013, 10:42 AM
2 cavity brass 358640 380 ACP HP please.
I need the base type you want... either plain base or gas check and which HP.... either large or penta you want.
Thread updated..............
Ruger480
04-12-2013, 04:22 PM
Sorry, plain base and Lg HP.
Thank you,
John
Buzz64
04-12-2013, 10:35 PM
OK, I'll play. .358 plain base four cavity with large and penta pins.
buzz at joniypc dot com
dogman
04-15-2013, 05:40 PM
I could also some advise. Planning on using for a PPK. Probably wouldn't load the round too hot. Would I need the gas check and which hollow point option would work better? Thanks
45 2.1
04-15-2013, 06:51 PM
I could also some advise. Planning on using for a PPK. Probably wouldn't load the round too hot. Would I need the gas check and which hollow point option would work better? Thanks
380s are notorious for not expanding jacketed HPs. You have to have a top end load with jacketed to get satisfactory results. With cast.... cast the large HP with 25 or 30:1 lead/tin and push it to top book loads. The GC will help you on that.
dogman
04-16-2013, 02:17 AM
I'd like a four cavity w/GC .358 with large pins
mlmaher at gmail dot com
harley45
04-16-2013, 07:26 AM
Can I change mine to a GC version please.
44 mag nut
04-18-2013, 10:42 AM
I'll take one 4C 0.358 PB Large HP and solid pin
magnut44 at gmail
Buzz64
04-18-2013, 11:44 AM
Hi 45 2.1
Looks like you are at (over) the 15 takers - this should go in pretty quickly now. Can't wait to try out a MiHec!
freebullet
04-19-2013, 05:11 AM
I'd like to sign up for 1 .358 plain base 2 cavity mold with penta hp pins. Thanks
Apexservicesomaha att g mail dott com
45 2.1
04-21-2013, 02:24 PM
I'll take one 4C PB Large HP and solid pin
magnut44 at gmail dot com
What size? 0.358" or 0.366".............
Hi 45 2.1 Looks like you are at (over) the 15 takers - this should go in pretty quickly now. Can't wait to try out a MiHec!
There are quite a few GBs in front of this one..... it will be a while yet.
Thread updated..............
4cavity pb mould all pins LUP rstaab (at) Panix dot com
.358 diameter
Darkh2odiver
04-21-2013, 09:14 PM
Here we go again..... Two cavity PB .358 Lg pins w/extra set of Lg pins
darkh2odiver (at) hotmail [dot] {com}
Thank you.
45 2.1,
Put me down for one 2 cavity 0.358" plain base mold with large HP pins...USSR.....ussr at empacc dot net. Thanks.
Don
45 2.1
04-22-2013, 09:33 PM
4cavity pb mould all pins
What diameter? .... 0.358" or 0.366"
Thread updated..................
Edited. .358 diameter. I'm a dope.
Bump, and a quick question for 45 2.1: It was stated that 15 commitments to buy were needed for this group buy to come to fruition. We have 22 commitments at this point. Is there a certain number of commitments or a certain date at which point the group buy will be closed and proceed on to the creation of the moulds? Thanks.
Don
Buzz64
04-26-2013, 11:12 PM
I'm with you USSR, seems like it should be "last call" time.
45 2.1
04-27-2013, 09:44 AM
Bump, and a quick question for 45 2.1: It was stated that 15 commitments to buy were needed for this group buy to come to fruition. We have 22 commitments at this point. Is there a certain number of commitments or a certain date at which point the group buy will be closed and proceed on to the creation of the moulds? Don
I'm with you USSR, seems like it should be "last call" time.
There is no "last call time" on any of the GBs I run. To be viable to have a run, the minimum number is 15 molds, but that doesn't mean that the GB will close and be ran at that time either. MiHec controls when a GB will close and when he makes it......... I do not.
Thanks for letting us know, 45 2.1.
Don
FatMcNasty
05-07-2013, 02:52 PM
45 2.1 can you remove my name from the list. I had some things come up. And cannot participate.
sparkz
05-21-2013, 04:17 PM
Ok Il Bite,
2cav (first Choice)
4cav (second Choice)
diameter? .... 0.358" (for my Colt Goverment 380acp so i think thats right size, to size down to 356)
Gas Checked,
with HP & penta HP, 1 set each total 2 (Pins to make it a RN Boolit come with the mold, correct?)
Sparkz1000 AT GmAiL Dot Com-awn
any est on when these may show up?
I know it's worth wait and I plan on a long wait
just wondering does this go in faster as its an older GB
TIA
Patrick
funshooter
05-21-2013, 04:50 PM
I will take a 4C brass mold hp with all the pins .358 PB and a handle
weldinspector at earthlink dot net
gtgeorge
05-23-2013, 05:09 AM
Please put me down for one 4 cavity, all pins, PB .358 gspatton at gttransmissions dot com.
45 2.1
05-23-2013, 09:19 AM
Reply to sparkz:
(Pins to make it a RN Boolit come with the mold, correct?) No, this mold is a flat nose, it looks like the picture in the first post.
any est on when these may show up? No estimate..... a guess would be a quite a while. MiHec closes the GB when he is ready to make it.
Thread updated.............
Buzz64
05-23-2013, 08:54 PM
MiHec just closed another GB I'm on (10mm) with over 75 on it. Yep, it will be awhile...
45 2.1,
Gonna have to drop out of this group buy. I need a mould sometime this century, and ordered one that is already made and ready to ship. Thanks.
Don
TMSCU
05-24-2013, 09:41 PM
I will take a 4C brass mold Gas Check HP with all the pins .358
email: tmoyer1952 at yahoo dot com
My Cast boolit name is TMSCU
Thanks
uncleskippy
05-28-2013, 09:42 AM
I would like a One 4 cavity 0.358" plain base mold with all pins
danielap at forsyth.cc
Thanks
Low Budget Shooter
05-30-2013, 12:40 AM
45 2.1, please change my pins to large HP and plain. Thanks, LBS
sparkz
06-02-2013, 08:05 PM
@ .45 2.1,, Right, sorry I ment a flat nose pin so I have choice of 3 boolits, 1) a Hollow point, 2) Smaller penta HP, and 3) Pins to make it a Solid FN Boolit, so like 3 molds in one seems like a great Idea for this little bad Boy, haha,,
Thanks Again for all your efforts to draw us all in one place for a great mold like this,
And ya have to know something like a nice custom as this one is, is worth the wait
Just Ichie to Pop a few with this one sorta gives new life to a old toy,,
Keep me in the loop
Patrick Campbell
Reply to sparkz:
(Pins to make it a RN Boolit come with the mold, correct?) No, this mold is a flat nose, it looks like the picture in the first post.
any est on when these may show up? No estimate..... a guess would be a quite a while. MiHec closes the GB when he is ready to make it.
Thread updated.............
freebullet
06-04-2013, 06:03 PM
I'm out, please take me off the list.
One 4 cavity 0.358" plain base mold with all pins &
One 4 cavity 0.366" plain base mold with all pins
both in the GC version
snowserver (at) hotmail d0t com
sergraf
06-13-2013, 01:53 PM
I'm in for 1 plain base 4 cavity mold at .358 with all the pins and a set of handles if possible.
sergio underscore rafanan at yahoo dot com
45 2.1
06-13-2013, 03:07 PM
One 4 cavity 0.358" plain base mold with all pins &
One 4 cavity 0.366" plain base mold with all pins both in the GC version
Just to clarify....... you have said plain base and gas check in the above. I put you down for two gas check molds. Is this correct?
Thread updated.............
redneckdan
06-13-2013, 10:04 PM
Just to clarify....... you have said plain base and gas check in the above. I put you down for two gas check molds. Is this correct?
Thread updated.............
Please put me down for a 2 cavity .358 with the regular penta pins.
Dan
BMKoenig
06-13-2013, 11:20 PM
Put me down for a four cavity, gas check, with large, penta, and solid pins. A set of handles as well.
rommelbmk (at) comcast (dot) net
Dannix
06-15-2013, 05:46 PM
Interesting, nice big meplat on this boolit. If you can grow this design to 115grn for non-kurtz 9mm, e.g. 9x19mm, I'd have to bite.
(I already have your/Miha's 9mm 125 gr. HP, but I'm always willing to try any other non-kurtz 9mm designs you may come up with.)
45 2.1
06-17-2013, 10:41 AM
Please put me down for a 2 cavity .358 with the regular penta pins.
Dan
Need a disguised e-mail address and the base style... either gas check or plain base.
Put me down for a four cavity, gas check, with large, penta, and solid pins. A set of handles as well.
I need the mold diameter you want... either 0.358" or 0.366".
Interesting, nice big meplat on this boolit. If you can grow this design to 115grn for non-kurtz 9mm, e.g. 9x19mm, I'd have to bite.
You won't need it with the HP, but you might get to see something like what you want.
Thread updated somewhat................
BMKoenig
06-17-2013, 06:29 PM
.358 diameter
tiger762
06-21-2013, 11:03 PM
Put me down for a 4-cavity, plain base, 0.358" diameter, with all possible pins, please.
kef 762 AT yahoo com
no space between 'f' and '7'
Thanks!
Rymark223
06-23-2013, 03:10 AM
I would like one four cavity 0.358 GC mold with large and penta pins and one four cavity 0.366 GC mold with large and penta pins.
Email sbmathews74 at gmail dot com
dkf..... krflff2 (at) dejazzd (dot) com .....One 2 cavity 0.358" Plain Base mold with All Pins and one set of handles
huntnfish72
06-30-2013, 10:35 AM
One 4 cavity 358 plain base with all the pins please
Billyv3 at newnorth dot net
Buzz64
07-01-2013, 07:30 PM
man I wish MiHa would do this one. Been waiting since January...
jwfox
07-06-2013, 02:03 PM
jwfox....jay dubya fox nine four eight zero AT America On Line dot com...One .358 plain base four cavity mold with both large and penta pins and flat pin and handles.
redneckdan
07-06-2013, 07:52 PM
I'd like mine plain base.
Email is dmhamilt (at) mtu (dot) edu
Thanks!
SP5315
07-17-2013, 12:20 AM
One 4 cavity .358 GC mold with all pins & one 4 cavity .358 PB mold with all pins.
wmclark AT email DOT com
Thanks
Sgtonory
07-20-2013, 07:57 PM
Like a .366 PB 4c Hp with all pins
Onory 1 at gmail dot com
CPL Lou
07-23-2013, 11:45 PM
My request was for a 2 cavity, gas checked, all pins.
You have me listed for a 4 cavity.
I am #10 on the list.
Thanks !
CPL Lou
Bruizer
07-26-2013, 01:57 AM
howmany grains is the. 358 640? What is the breakdown with the hollowpoints. Also why are you casting a 9 mm at. 358? Shouldn't you be casting it at. 356?
45 2.1
07-26-2013, 09:12 AM
howmany grains is the. 358 640? What is the breakdown with the hollowpoints. Also why are you casting a 9 mm at. 358? Shouldn't you be casting it at. 356?
You might want to look at the first post.... specifically the picture. 9mm's come in a large variety of barrel dimensions. 0.356" is much too small for decent results.
Corrected CPL Lou!
Thread updated...........
Bruizer
07-26-2013, 09:21 AM
put me down for a 4 cav. 358 with hp and hexa pins and gas check
b dot rolfe1 at bellaliant dot net
kayak1
07-26-2013, 09:22 AM
One 4 cavity 0.358" plain base mold with all pins jason at kates (dot) [org]
kayak1
07-26-2013, 09:27 AM
I just noticed other people are ordering these with handles. I didn't noticed anything in the original post as to handles.
What type of handles does this mold require? I would love to have it show up ready to run but I would need to know how much extra the handles will cost (including shipping).
I have an extra set of Lyman handles that I purchased for a Lyman 311041 that I was going to order before I read about people having issues with it running undersized.....
timberhawk
07-26-2013, 01:19 PM
I just noticed other people are ordering these with handles. I didn't noticed anything in the original post as to handles.
What type of handles does this mold require? I would love to have it show up ready to run but I would need to know how much extra the handles will cost (including shipping).
I have an extra set of Lyman handles that I purchased for a Lyman 311041 that I was going to order before I read about people having issues with it running undersized.....
These molds take Lee 6 cavity handles.
kayak1
07-26-2013, 04:59 PM
These molds take Lee 6 cavity handles.
I just found a link to the noe handles:
http://noebulletmolds.com/NV/product_info.php?cPath=69&products_id=380
They looks nice, I like that they are pinned and seem nicer than the LEE or RCS ones.
Please include a set with my mold purchase.
cja245
07-26-2013, 05:11 PM
This group buy is for a Mihec mold not NOE.
These are the handles that folks are ordering in this buy. I don't know that NOE handles are necessarily compatible.
http://www.mp-molds.com/shopping/pgm-more_information.php?id=6&=SID
kayak1
07-26-2013, 10:42 PM
This group buy is for a Mihec mold not NOE.
These are the handles that folks are ordering in this buy. I don't know that NOE handles are necessarily compatible.
http://www.mp-molds.com/shopping/pgm-more_information.php?id=6&=SID
Sorry I think that I have been looking at too many sites dreaming about molds. The MP Molds handles look nice too. If they are making the mold I think that I should go with their handles.
45 2.1
07-28-2013, 12:00 PM
put me down for a 4 cav. 358 with hp and hexa pins and gas check
Please look at the list and confirm that is what you wanted.
Thread updated.................
MJohnston
07-31-2013, 05:13 PM
Would it be possible to mix it up to feed multiple guns? In other words a 4 cavity with 2 gc and 2 pb, maybe even one cavity .366?
45 2.1
07-31-2013, 05:18 PM
Would it be possible to mix it up to feed multiple guns? In other words a 4 cavity with 2 gc and 2 pb, maybe even one cavity .366?
MiHec has not mixed any of those possibilities in the same mold as of yet...... I doubt he will either.
I would like one 4 cavity 0.358" plain base mold with all pins.
edotson123 (at) tx (dot) rr (dot) com
autodidact
08-18-2013, 10:27 AM
Please include me for the following.......
One 4 cavity 0.358" plain base mold with all pins
jbpaul (at) suddenlink (dot) net
Thanks,
JB
wymanwinn
08-21-2013, 12:39 PM
I'm in...
one 4 cavity, .358 plain base, all pins, handles
wyman(dot)winn(at)verizon(dot)net
wyman
Ironwood
08-27-2013, 08:41 AM
Ironwood.....ironwood of evergreen at yahoo dot com.....One 4 cavity .358" plain base mold with all pins.
Update = I would like to order handles too.
Thank you!
Rm
Low Budget Shooter
09-12-2013, 12:57 PM
I'm sorry, but funds are getting tight, and I have to bail out of this. Please remove me from the list. Thanks! Low Budget Shooter
Bluestraw
09-14-2013, 12:26 AM
In for one 4 cavity 0.358" gas check mold with all pins.
Bluestraw at a o l (d o t) c o m
Buzz64
09-14-2013, 07:30 PM
45 2.1
Think I understood the blank pin (for solid boolit) comes with the mold. If it doesn't please add it to my request, I'm #16
45 2.1
09-14-2013, 08:29 PM
Think I understood the blank pin (for solid boolit) comes with the mold. If it doesn't please add it to my request, I'm #16
Usually, you can invert the HP pins for a flat nose........ this does leave the HP portion below the bottom mols surface so it can be damaged or puncture you or something else. The blank pin precludes that happening. I added a blank pin set to your choices.
Thread updated...........
Buzz64
09-15-2013, 10:47 AM
Perfect, thanks!
Ironwood
09-17-2013, 12:24 AM
I am #40 on the list and would like to change my order to a gas check base please.
Thanks,
Ironwood
Please add solid pins to mine as well. (#31 on the list) Thanks
45 2.1
09-22-2013, 12:50 PM
Please add solid pins to mine as well. (#31 on the list) Thanks
They were there with the all pins statement.
Thread updated..............
Ironwood
09-24-2013, 12:42 AM
Thanks for updating my order.
Ironwood
Buzz64
09-24-2013, 10:51 AM
MiHec has just sent out paypal for another GB - for the 125 9mm. So he's back at it!
xacex
09-25-2013, 07:13 PM
Is this short enough to keep the gas check inside the neck on a 357 sig? It looks like the closest we have come to something that would work well in that tiny bottleneck with a gas check. If it does it would be a 1500 to 1700 fps boolit.
Is this short enough to keep the gas check inside the neck on a 357 sig? It looks like the closest we have come to something that would work well in that tiny bottleneck with a gas check. If it does it would be a 1500 to 1700 fps boolit.
Good question. I am going to try the PB mold in .357sig so see how it does. If it don't work well no big deal I load .380. Accurate has a 125gr GC for .357sig in their catalog also.
45 2.1
09-25-2013, 07:41 PM
Is this short enough to keep the gas check inside the neck on a 357 sig? It looks like the closest we have come to something that would work well in that tiny bottleneck with a gas check. If it does it would be a 1500 to 1700 fps boolit.
Good question. I am going to try the PB mold in .357sig so see how it does. If it don't work well no big deal I load .380. Accurate has a 125gr GC for .357sig in their catalog also.
I just added this to the first post:
Edit: For those of you wondering about it's use in the 357 Sig, here are the parameters.
If you seat the GC version to the base of the neck, 0.035" of the front band shows and the cartridge is under the spec length of the cartridge. If you seat the front band to the end of the case, about half of the GC surface is in the case with no lead exposed. Either way it looks to work out.
The plain base version is about 0.013" shorter on the bearing body than the GC version.
I just added this to the first post:
Edit: For those of you wondering about it's use in the 357 Sig, here are the parameters.
If you seat the GC version to the base of the neck, 0.035" of the front band shows and the cartridge is under the spec length of the cartridge. If you seat the front band to the end of the case, about half of the GC surface is in the case with no lead exposed. Either way it looks to work out.
The plain base version is about 0.013" shorter on the bearing body than the GC version.
What would the approx COAL be with the GC version?
45 2.1
09-26-2013, 10:37 AM
What would the approx COAL be with the GC version?
1.133" if seated to the base of the neck
1.133" if seated to the base of the neck
That COAL should do just fine. Most factory .357sig is 1.125" COAL. I have not ran into feeding issues in my Glocks until I start getting above max COAL around 1.145" or so.
xacex
10-15-2013, 12:46 PM
rogue_diablo (at)yahoo(dot)cOm
I'm game. 4 cavity .358 G/C with all pins.
mckenziedrums
10-15-2013, 03:30 PM
This place gets expensive..
4 cavity .366 PB with all pins please
mckenziedrums at gmail dot com
Buzz64
10-22-2013, 06:37 AM
15 'to commit' and 43 on the list. I know you don't run the show 45, and appreciate your honcho-ing this (and other) GBs. MiHec is a busy guy these days.
Virginia John
10-22-2013, 06:46 PM
If it is not too late, I would like to be included.
jwstuartjr at hotmail dot com
One 4 cavity 0.366" plain base mold with all pins
Thanks
eezz, please put me down for 1 4 cavity HP .358 GC mold with all the pins & handles. and 1 4 cavity HP 0.366 with pinta pins & handles. Thanks eezz at g mail dot com
oldsingleshots
10-31-2013, 12:23 PM
If open still - count me in.
1 2 cavity HP 0.358 G/C with all pins and handles
haletree at att dot net
Thanks.
cja245
10-31-2013, 12:36 PM
Please add a second mold to my order: a 4-cavity HP .358'' plain base with large and penta pins.
Thanks,
Chris
9. cja245.....cja245 at gmail dot com.....One 4 cavity 0.366" plain base mold with large and penta HP pins
tygar
10-31-2013, 04:45 PM
I'll take a 2 cavity solid & small HP, PB .358.
tbrolliniATgciDOTnet
Aaron
11-02-2013, 10:15 AM
Add me please. 4 cavity all pins .358
Aaron
5090shiloh at gmaildotcom
45 2.1
11-03-2013, 11:33 AM
4 cavity all pins .358
You need to state the mold type..... gas check or plain base.
Thread updated.................
45 2.1. Please change mine #31 to:
One 4 cavity 0.358" gas check mold with all pins
45 2.1
11-08-2013, 05:48 PM
Aaron....You need to state the mold type..... gas check or plain base.
Thread updated.................
head for the hills
11-26-2013, 10:36 PM
Retracted, the mold diameter is too small for my barrel. I would need about a .360" mold.
Retracted, the mold diameter is too small for my barrel. I would need about a .360" mold.
I would actually prefer if this mold would drop .360". The molds I get made for .380/9mm/.357sig I spec to drop at .360 and then I size them down to what I need.
wymanwinn
12-11-2013, 02:04 PM
45 2.1...
any idea when Mihec will begin production....????
wyman
doctorggg
12-12-2013, 06:44 PM
1 mold 4 cavity .358 PB with all pins
gggmmg at verizon dot net
Sgtonory
12-12-2013, 07:13 PM
#35 on list. Need to cancel sold 9x18 pistol thanks.
chprplt
12-16-2013, 02:59 PM
Please add me to the list for 1, 4 cavity, .358, with all pins. thank you.
chprplt-- exit 13 five at aol dot com
Aaron
12-29-2013, 02:47 PM
I am 48 need pb
Thanks
Aaron
AZBrian
12-29-2013, 09:58 PM
Please add me for the following two molds:
(1) 4 cav .358 plain base HP mold with all pins
(1) 4 cav .358 gas check HP mold with all pins
sellsell(at)cox(d0t)net
Thanks!!
atom73
12-30-2013, 02:25 PM
2 cav .358 plain base, large pins, and handle please. Email is neilsbohr73@ yahoo. you know what.
redrock
01-01-2014, 10:39 AM
Put me down for (1) 4 cavity .358 plain base/lg hp pins
cuffem 4 at centurytel dot net
mpbarry1
01-05-2014, 02:31 AM
I'll take a four cavity .358 with all the pins. Plain base please.
mpbarry1 at gmail dot com
thanks!
updated.
Buzz64
01-05-2014, 12:32 PM
Almost a year and nearly 50 sign-ups - maybe it will make MiHec's radar soon :)
hicard
01-21-2014, 10:45 AM
I will take a 2 cavity pb w/large hp pins in .358. hicard21atoutlookdotcom
I take it this is the first run ever done on this design?
rnelson11
01-26-2014, 10:35 AM
I have been casting for a while but have never used gas checks. I am interested in the bullet but can't seem to find a GC for it. What GC do you guys use for a 9mm bullet?
gefiltephish
01-27-2014, 06:02 PM
35 cal.
rnelson11
01-30-2014, 09:27 AM
4 cav .358 with gas check and all pins
rnelson11 at chesnet dot net
45 2.1
02-08-2014, 03:49 PM
Please add me to the list for 1, 4 cavity, .358, with all pins.
plain base or gas check mold?
I'll take a four cavity with all the pins.
mold size: 0.358" or 0.366" and plain base or gas check mold?
I will take a 2 cavity pb w/large hp pins.
mold size: 0.358" or 0.366"
I take it this is the first run ever done on this design?
Yes.... it is.
I have no idea when this will be ran. I'll post that when I know myself.
Thread updated.................
SethD
02-16-2014, 12:11 PM
4 cavity, GC, 0.358. Large HP pins & flat pins. (seth doty 44 4 at hot mai l dot com)
xacex
02-19-2014, 05:14 AM
Take me off this one #42. Thanks. Decided to wait for a different mold to come up.
unknownhavoc
02-19-2014, 11:59 PM
Would it be possibly to get a two cavity cut with one of each size, or a four cavity with twof each?
I doubt it, as I see no mention of this, but I don't cast very often for these, so this would kill two birds with one stone.
45 2.1
02-22-2014, 10:55 AM
Would it be possibly to get a two cavity cut with one of each size, or a four cavity with twof each?
Sorry, no................
Thread updated.................
chprplt
02-22-2014, 12:10 PM
Quote Originally Posted by chprplt View Post
Please add me to the list for 1, 4 cavity, .358, with all pins.
Plain base, please. Sorry for the inconvenience. Thank you.
Gun-adian
02-26-2014, 12:57 AM
Sorry, but I have to back out of this one.
Please remove #8.
Thanks
rcwarship
03-08-2014, 12:38 AM
rcwarship.....rcwarship at comcast dot net
One 4 cavity 0.358" plain base mold with large & penta HP pins
Handloader109
03-11-2014, 06:59 PM
Is this still open? If so, I'd like to jump in.
Handloader109, jliferjr at yahoo dot com,
One 2 cavity mold, 0.358, Plain base please, both plain and penta HP pins.
Thanks
maderawood6
03-11-2014, 10:44 PM
put me down for a 4 cavity .358 plain base with all the pins
maderawood6 at geemail dot com
CPL Lou
03-19-2014, 10:49 PM
:coffee:
CPL Lou
rcwarship
03-25-2014, 06:37 PM
Good day 45 2.1, looks like I was overlooked on the list, please see post #159.
Thanks & Best Regards,
Jon
45 2.1
03-25-2014, 07:35 PM
Good day 45 2.1, looks like I was overlooked on the list, please see post #159.
Thanks & Best Regards,
Jon
No, you weren't overlooked, just located differently. When someone wants off (like in post #158), I put the next person in that place. You're in the #8 listing. Sometimes kinda hard to find when you expect to be at the end of the list.
rcwarship
03-25-2014, 08:36 PM
Oooops, my bad. You are exactly right, I expected to see it at the end & did not think to look elsewhere.
Thank you very much for the info & especially for doing the work on this thread. You the MAN!
Thanks Again & Best Regards,
Jon
Buzz64
03-26-2014, 07:49 AM
14 months - I know Mihia has his own schedule but jeeze...
ballistim
03-26-2014, 11:32 AM
One 4 cavity 0.366" plain base mold with penta HP pins please.
ballistim(at)yahoo(dot)com
45 2.1
03-30-2014, 08:47 AM
14 months - I know Miha has his own schedule but jeeze...
This isn't as old as some other GB's. Patience is one of the virtues.
Thread updated.................
tiger762
04-01-2014, 10:55 PM
I'd like a 4-cavity, non-GC, 0.358", Large HP please....
kef762 AT yahooDOTcom
ballistim
04-05-2014, 04:41 PM
One 4 cavity 0.366" plain base mold with penta HP pins please.
ballistim(at)yahoo(dot)com
Still don't see me on list, am I just not seeing it?
ballistim
04-05-2014, 04:42 PM
Oops, spoke too soon! Sorry...
wacki
04-05-2014, 07:37 PM
What grain is this?
45 2.1
04-05-2014, 07:43 PM
What grain is this?
That's shown on the drawing in post #1...... Approximately 96 gr. solid or 87 gr. hollow point dependent on choice of diameter and alloy.
taugust
04-11-2014, 10:05 PM
I would like to be on the list for this one.
g99jeb at aol dot com
One 4 cavity 0.358" plain base mold with a penta and a blank pin.
Thank you.
Tom
HillBilly2
04-13-2014, 08:48 PM
Put me down for one 4 cavity 0.358" plain base mold with a penta and a blank pin.
ffrisby AT hot mail dot com
Thanks
Ironwood
04-24-2014, 12:03 PM
I'm #40 on the list. Please remove the handle option that I requested.
Thank you!
Buzz64
04-24-2014, 09:17 PM
Miha just closed a gb on a 40 cal that isn't as old as this one (started 4-20-13) - hope we haven't dropped below his radar.
45 2.1
04-24-2014, 10:24 PM
Miha just closed a gb on a 40 cal that isn't as old as this one (started 4-20-13) - hope we haven't dropped below his radar.
No.... GB's don't go in order most of the time.
Thread updated.................
J & D Armament
04-30-2014, 04:36 PM
I'm new to this and hope I did this right. And I hope I can get into this buy. Please let me know what else I need to do. Thanks.
I would like (1) one 4 cavity .358 plain base mold with the penta pins.
Jdarmament at gmail dot com
45 2.1
05-09-2014, 12:30 PM
Thread updated.................
double00
05-13-2014, 12:05 PM
i will take a four cavity plain base .358" with all the pins.
jcgraeler at gmail dot com
funshooter
05-16-2014, 02:05 PM
I am # 23 on the list can you please remove the handles from my order please
tja6435
05-20-2014, 10:12 AM
I'll take a
4 cavity, plain base, large and penta pins
Tja6435 at gmaildotcom
45 2.1
05-20-2014, 10:49 AM
I'll take a 4 cavity, plain base, large and penta pins
Mold size... 0.358" or 0.366"??????
Thread updated.........
tja6435
05-20-2014, 11:03 AM
Sorry, .358". Must've missed the diameter choice.
Thanks
CPL Lou
06-05-2014, 07:45 AM
:coffeecom
CPL Lou
HansOlo
06-11-2014, 07:04 PM
Forum name: HansOlo
I'd like one 4-cavity .358 plain base mold with the penta HP pins please.
Contact email: carter (dot) jacob (dot) w (at) gmail (dot) com
Thanks.
45 2.1
06-17-2014, 05:47 PM
Thread updated.........
Buzz64
06-18-2014, 12:25 AM
Can't believe it, my patience that is. 17 months and I still want it!
CPL Lou
06-21-2014, 10:42 PM
Any idea when this will be made ?
CPL Lou
Buzz64
06-24-2014, 11:47 AM
Please, MiHa, run this one soon.
timberhawk
07-03-2014, 09:13 AM
bump!
Buzz64
07-04-2014, 10:20 AM
bumpety - bump - bump
timberhawk
07-18-2014, 09:23 AM
bump!
wymanwinn
07-18-2014, 12:36 PM
this is taking entirely too long.....18 months and no production schedule in sight...!!!!!
please remove me from the GB...
wyman
mckenziedrums
07-18-2014, 02:10 PM
45: Please remove me from this one. I don't have a need for this one any more. My luck it'll be the next one picked up and I'd have to go buy another gun ;)
redrock
07-20-2014, 03:23 PM
Please remove me from the list #52.
Buzz64
07-20-2014, 04:50 PM
Looks like Mihec might be loosing more than gaining on this one...
45 2.1
07-20-2014, 05:12 PM
Looks like Mihec might be loosing more than gaining on this one...
What concerns one fellow may not concern another.... each to his own. With the atmosphere that has been going on in the gun world, a lot of things are not available. I look at people that leave as not getting a better product/performance.
This is just how group buys can be, especially for a first time design. I am going to have another .380 to feed and could use this mold but I'll wait until it comes around.
HansOlo
08-03-2014, 08:48 PM
Please remove me from this group buy.
Financial things make me have to choose between this buy and the .45 rcbs rerun. I'm choosing the .45. :)
bquardt
08-06-2014, 04:38 PM
Can I still get in on this group buy?
uncleskippy
08-07-2014, 08:34 AM
Please remove me from this group buy.
Financial things made me sell my gun.
Thanks
Handloader109
08-13-2014, 08:23 PM
Can't wait any longer. Going with a US made mold. Please remove me from the list.
Thanks
jeremiah.allen1
09-17-2014, 05:45 PM
Can I been added to the group buy. I want a .358 plain base mold with all pins. jeremiah (dot) allen 1553 (at) gmail (dot) com Thanks
CPL Lou
09-20-2014, 01:14 AM
:coffee:
CPL Lou
I am #31 on the list. Please change mine to Plain Base instead of GC.
funshooter
09-23-2014, 11:35 PM
I wanted the delete this reply and it will not let me
timberhawk
10-14-2014, 09:13 AM
Shameful bump
harley45
10-14-2014, 11:33 AM
I'd like to change my order to a 2 cavity, non gas check version with all the pins please.
thanks.
dieselrealtor
10-27-2014, 10:38 PM
Is there an eta on when it will go into production?
thanks.
Is there an eta on when it will go into production?
thanks.
God I hope soon.....
dieselrealtor
10-29-2014, 11:36 PM
put me down for a 2 cavity.358, plain base with all pins.
doug at realtorsink dot com
How well will a GC base fly without the gas check on this short of a boolit?
timberhawk
11-20-2014, 02:52 PM
Can it really be that we are a month away from two years?
FLYCUTTER
11-25-2014, 01:37 AM
Wonder when this is going to close.
45 2.1
11-25-2014, 11:30 AM
Can I still get in on this group buy?
Yes, just follow the directions in post #1
I want a .358 plain base mold with all pins.
Do you want a 2 or 4 cavity mold?
I'd like to change my order to a 2 cavity, non gas check version with all the pins please.
Still 0.358" diameter as before..................
How well will a GC base fly without the gas check on this short of a boolit?
Not very well since it is quite short...........
Wonder when this is going to close.
We all wonder that, but since this is a very unique boolit for the cartridge..... I'm going to wait and hope it is really soon. A PM to MiHec might encourage it along also.
Thread updated....................
gtgeorge
11-25-2014, 11:47 AM
A PM sounds like a good idea. :bigsmyl2:
TMSCU
12-07-2014, 02:09 PM
I will take a 4 cavity .358 GC with large and penta pins tmoyer1952at yahoo dot com
castblast
12-24-2014, 12:43 AM
I would like One 4 cavity 0.358" plain base mold with all pins
sthwld64atgmaildotcom
Sgt Petro
12-27-2014, 12:18 AM
aaronpetroski at gmail dot com ... 2 cavity plain base .366 all pins
cja245
12-27-2014, 12:42 AM
9. cja245.....cja245 at gmail dot com.....One 4 cavity 0.366" plain base mold with large and penta HP pins and One 4 cavity 0.358" plain base mold with large and penta HP pins
45 2.1,
Please remove the 4 cavity .366" mold. Sold the Makarovs, no longer need it.
Still in for the 4 cavity .358" mold
Thanks,
Chris
silverjay
01-12-2015, 01:09 AM
Please add me to the list. One 0.358" four cavity with large pins. Silverjay7 at gmail dot com.
Thanks
dragon813gt
01-12-2015, 07:18 AM
I would like a four cavity plain base at .358 w/ all pins dragon813gt at yahoo dot com.
45 2.1
01-12-2015, 10:36 AM
Please add me to the list. One 0.358" four cavity with large pins. Silverjay7 at gmail dot com. Thanks
I would like a four cavity plain base at .358 dragon813gt at yahoo dot com.
OK, you two guys are missing some information. Look at the list on page 1 and PM MiHec what is missing (if you don't want someone else choosing for you. A PM to you both will be sent.
Thread Updated......................
This GB is Closed.....
Any changes or requests for molds need to go to MiHec via PM now.
ballistim
01-12-2015, 11:02 AM
Glad to hear it's closed! I'm set up with everything I need to turn 9x19 NATO brass into 9x18 brass & am looking forward to shooting cast in my Makarov, hoping it's here before summer.
dragon813gt
01-12-2015, 11:10 AM
Updated my original post. I had "all pins" typed in my head :)
MostlyOnThePaper
01-12-2015, 11:11 AM
I really wanted one of these for my 380, but not knowing when the call for payment was going to happen and already waiting on the 44 mold that's I think held up on pins, I had to hold off. Hopefully the 44 pins show soon, that gets cleared and I can catch one of the extra ones of this. Wouldn't be the first time.
fixit156
01-12-2015, 08:30 PM
Where should I send payment? Sorry if I mist the info how to do it
dragon813gt
01-12-2015, 08:41 PM
Where should I send payment? Sorry if I mist the info how to do it
Payment is not due yet. Miha will send you a Paypal request when the molds are ready to ship.
fixit156
01-15-2015, 03:03 PM
Thanks will wait for it
MiHec
03-03-2015, 09:32 AM
Molds are on the machine in final stage. Here.... (https://www.facebook.com/MPmolds/posts/1623524334545002:0)
gtgeorge
03-03-2015, 10:00 AM
Excellent news Miha and thanks for the update.
MiHec
03-03-2015, 12:22 PM
And finished product.....
132664
Buzz64
03-03-2015, 12:37 PM
Waiting anxiously for my pp invoice! Two molds in one gb - .380 and Mak - been saving some lead for these guys!
Buzz64
03-09-2015, 07:23 PM
Still no PP invoices :shock:
dragon813gt
03-10-2015, 02:05 PM
Received an invoice today. Forgot all about this mold :laugh:
MiHec
03-10-2015, 02:10 PM
PAYPALS are out!
If you missing one, let me know via PM
silverjay
03-10-2015, 02:19 PM
PayPal sent. Thank you.
Crosbyman
03-10-2015, 02:30 PM
I also received and paid an invoice today for a four cavity. What brand handles work?
gtgeorge
03-10-2015, 03:13 PM
Paid and crossing fingers that USPS delivers this one in a timely manner.
Crosbyman, Miha sells some nice handles but the Lee 6 cavity ones will work and get you by.
Buzz64
03-10-2015, 06:57 PM
YES SIR!!! Received both invoices (.358 and .366) and paid just now. Been waiting forever for these guys!
AZBrian
03-10-2015, 10:51 PM
Received both invoices and paid. But I paid under a different PayPal address (brian(d0t)dinse(at)yahoo(d0t)com), instead of sellsell(at)cox(d0t)net. Hope that works out okay. Gave my same address. Thank you!!!!
MostlyOnThePaper
03-10-2015, 10:57 PM
No invoice, pm sent!
I was a last minute add on via pm.
FLYCUTTER
03-11-2015, 04:52 PM
pay-pal sent for .358 & .366
SP5315
03-12-2015, 09:07 PM
Payment for two molds sent this afternoon.
ballistim
03-12-2015, 09:09 PM
I paid before the first post here, just forgot to say so! Looking forward to casting these for my Makarov.
MostlyOnThePaper
03-12-2015, 09:09 PM
Paid, thank you!
hicard
03-13-2015, 11:52 AM
Paid by PayPal
dieselrealtor
03-17-2015, 06:31 PM
Paid a few days ago, is there an eta on when they are expected to ship?
Usually you get the mold within 2 weeks after you pay. It depends on delays with customs and the postal services.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.