25 Cal. Molds?

[kcajeel]

Does anyone know of any custom mold makers that are making 25 cal. molds now?
Thanks

[JerryW]

Try David Moss, he makes match winning 25 cal. moulds. JerryW

[Shuz]

Does anyone know of any custom mold makers that are making 25 cal. molds now?
Thanks

Whatcha plan on shooting in .25 cal?

[tonyjones]

Try Veral Smith at LBT. David Mos' wife, Shelly I think, recently posted here that they have gotten out of the mould business.

Regards,

Tony

[MT Chambers]

Hoch, Jim Borten, Leeth, etc....you'll have to decide on straight sided or tapered as most are breech loaded.

[Wayne Smith]

Our own NOE made my (and Blammer's!) .25 Heavy, and in two sizes in the same block.

[Stick_man]

When asking about .25 caliber molds, are you referring to pistol or rifle? You could probably get either from Accurate Molds or NOE may have one or two in stock for the rifles.

[9.3X62AL]

RCBS has at least one mould design listed (120 grain SP) and a limited-production 100 grain flat-point as well. RCBS also shows their 85 grain plain-base Cowboy mould for the 25-20. Lyman still has their #257420, which runs about 72 grains minus GC. SAECO has at least one mould in 25 caliber as well. These aren't "custom" makers, but they will work in 25 caliber rifles quite well. I gave NV ground squirrels a lot of stress with #257420 this spring.

[shooter93]

Accurate molds doesn't make molds below 30 caliber.

[Casting_40S&W]

RD has em.

http://www.ranchdogoutdoors.com/index.php?main_page=product_info&cPath=1_6_22&products_id=18

[Green Frog]

Does anyone know of any custom mold makers that are making 25 cal. molds now?
Thanks

Ya still gots ta tell us rifle or pistol... it makes a difference. I would check with Jim Borton for a rifle mould as the "Quarter Bore Corps" is quite active in the American Single Shot Rifle Association. For pistolas, I don't know where to tell you to look.

Froggie

[frnkeore]

If you are interested in a heavy breech seated bullet, I've had a cherry made by PT&G to put together a group buy and am looking for people to go in on it to lower the cost.

This is it,

Frank

http://castboolits.gunloads.com/imagehosting/thum_88524ff1f0e9e4ae8.jpg (http://castboolits.gunloads.com/vbimghost.php?do=displayimg&imgid=5736)

[1114h]

Frank,might be interested--what twist would stabilize this bullet? 1114h

[frnkeore]

I design it for 10 twist barrels. It has a Miller stability factor of 1.44 @ 1400 fps and 1.49 @ 1550 fps when shot in a 10 twist barrel.

Frank

[sisterjim]

Did you ever get this mold into production. I can't get the image to size up in any detail but would imagine this is just the boolit to paperpatch in my 6.5

[Bad Andy]

I am also looking for a .25 ACP mould for a Colt 1908-1910 pocket pistol I inherited from my wife's Grandfater this past Winter. I have been able to find ammo for it but of course want to cast and reload my own eventually. I think the Winchester ammo I shoot out of it now is reloaded with a 50 grain FMJ bullet.

[tward]

Rcbs and LBT catalog .251 50 gr molds. Tim

[MaxJon]

http://www.castbulletengineering.com.au/bullet-moulds/rifle/25-calibre/258-95gc-triple-cavity

This 95gn Aussie made mold, looks good!! Hope it likes 12 twist 25 303......

[georgerkahn]

I have been seeking a mould to cast .25ACP bullets. My top three wants include:
Lyman 252-435
RCBS 25-050-RN
NOE RO-TL255-50 RF
Ringing Lyman, RCBS (including Huntington Die) -- none seem available. I posted a WTB on this site with no results. Buffalo Arms lists the RCBS, but it may need to be made "in-house" by them. Albeit I rate Buffalo's moulds as high as one might rate -- I have a .38 S&W they made for me which is awesome -- I'm too poor to make an inquiry re the .25acp mould -- in the $200 USD range...
geo

[Teemu]

MP-Molds has one...
https://www.mp-molds.com/bullet-casting-equipment/?pa_caliber=252

[Teddy (punchie)]

How many grain bullet are you looking for? I have a 65 gr mold 257420 Lyman mold I'm going to start casting some. Going to slow them down in the Robt and see how they shoot. Something for us to play with me and the girls. I would be willing trade some boolites for like 25 cal gas checks (?). Or maybe a lead trade. Let me know what you think and how hard of bullets, I don't think I have a sizer for the .252 ?? .257, .258 maybe one more, is going to be about it. I would guess you can lap out a old 243 ?? sizer ??.

[MaxJon]

How many grain bullet are you looking for? I have a 65 gr mold 257420 Lyman mold I'm going to start casting some. Going to slow them down in the Robt and see how they shoot. Something for us to play with me and the girls. I would be willing trade some boolites for like 25 cal gas checks (?). Or maybe a lead trade. Let me know what you think and how hard of bullets, I don't think I have a sizer for the .252 ?? .257, .258 maybe one more, is going to be about it. I would guess you can lap out a old 243 ?? sizer ??.
Thanks for your generous offer.
I'm simply going to buy the CBE 95gn one I posted the link to earlier. I think it will sit the GC in the neck of the case nicely.

[skeettx]

WHERE is frnkeore

Lives in Oregon

Anyone heard from him lately?

Last posted 02-28-2018

Mike

[hockeynick39]

Try Arsenal Molds. I bought an 85 gr, 257 cal. mold from them and it works great!!!

http://arsenalmolds.com/products?product_id=56

[MaxJon]

Would a plain base mould at sensible PB velocity be good for 100m target practice??

[Herb in Pa]

http://castboolits.gunloads.com/showthread.php?360872-257-Roberts-amp-NOE-260-122-FN-AN2

[Chev. William]

NOE lists several .251-.255 inch diameter bullet molds suitable for .25ACP and also many of .257-.258 inch diameter for Rifle use.

Chev. William