MiHec brass 4 cavity Cramer - 45 RCBS HP

[45 2.1]

Anybody interested in a 45 Hollow Point? The nose is the basic RCBS cowboy boolit that feeds slick as a gut thru the 1911s out there. We've had a GB on that RCBS boolit in the past. This is an updated version. The meplat is bigger than the BD and most others out there. The solid version hits with authority and matches ball weights. HP options (one set included with mold) will be 1) large HP, 2) penta HP, 3) blank pins ( free if HP pins or not reversible) or an extra cost set if you want a flat mold bottom while casting solids.

Price is $120 with one set of pins included plus $16 for each extra pin set wanted plus $20 shipping. I might run the active thread as a 2 or 4 cavity GB if enough want a two cavity.




Interest list 15 minimum needed for a GB:
Firefly
40Super
harley45
square butte
only1asterisk
HangFireW8
GLL
almostgem
denul
Beau Cassidy
lup
GMT210
ipijohn
Leadmelter
saz
dutch41
hamour

[FireFly]

Nice,nice! Almost did not see this. Any hollow-point options?

[40Super]

It may interest me.Depending on options. PB,penta or hex HP.

[harley45]

I'd like one with round pins and flat pins!

[square butte]

I'd be in.

[FireFly]

How does this work; first you need a minimum number of responses. Then a price and time is set.

45 2.1 Bullet Designer Thanks for designing this bullet.

[only1asterisk]

Oh yeah!

I was actually thinking to ask you you about this one...

I'm solid in!

[FireFly]

Anything happen with this cast bullet???

[HangFireW8]

I'm in.

[GLL]

FireFly:

Mihec really does not get very involved with these new Group Buys in the early "Discussion" stage until we sort out what is wanted and get members organized and committed to the formal “Active Group Buy”.
Although I like this bullet it looks like it may take awhile to generate enough interest to proceed to the “Active” stage. I have run seven Group Buys and they are a SLOW process in most cases ! :)

I like the BD but would take one of these as well !

Jerry

[almostgem]

I'm interested. Just getting started casting, but it looks like something my para would really like.
John

[denul]

I'd be in for a 4 cavity round HP. Not sure how many are required to move to an active GB or to secure Mihec's interest.

[Beau Cassidy]

I am good for a 4 cavity round HP.

[lup]

I'd be in for a 4 cavity with round, penta and flat pins.

[45 2.1]

Bump.................

[40Super]

I guess that I will be in for a 2C with round and penta pins,not interested in it as a solid. PB would be prefered .

[GMT210]

I'd be in for a 4 cavity, 0.452 with medium round and flat pins.

GMT

[ipijohn]

I'd also be in for a 4 cavity, 0.452 with penta and flat pins.

[GRUMPA]

This has me interested, would still like the details as far as HP is concerned (style of HP). I just got done with a GB from NOE so this 1 I'm kinda new at as far as what material the mould is made from, aluminum, brass and so on.

Of course price, cavity availability and so on, unless I missed it somewhere.

But my desire to get one has sure peeked.

[45 2.1]

This has me interested, would still like the details as far as HP is concerned (style of HP). That depends on what everyone wants. This could be the large HP, penta HP or a solid via either reversed HP pins or a blank pin. I just got done with a GB from NOE so this 1 I'm kinda new at as far as what material the mould is made from, aluminum, brass and so on. Brass, as per the title.

Of course price, cavity availability and so on, unless I missed it somewhere. Ideally, it would be 4 cavity...... but Miha might make them in two or four cavity.

[Leadmelter]

First time on a group buy.
I would be in for a 4 cavity, .452 with a set of complete set of pins:flat, round and hex.
Gerry
MI

[hicard]

That sure is an aggressive hp cavity. Should act like a handgrenade.

[45 2.1]

That sure is an aggressive hp cavity. Should act like a handgrenade.

Typically the nose blows off breaking into #5 shot size squareish pieces to the base of the hollow point leaving a ragged front surface with the rest of the base going thru the animal. Thats been tested on quite a few deer where its legal to do so. Thats what is needed to make the smaller less powerfull handgun cartridges effective. It even works on the 32 ACP as tested on MiHecs latest 32 ACP HP mold. Extensive destruction on small varmints with it. This boolit would make a 45 ACP a lot better killer on larger varmints and smaller large game.

[40Super]

Thats what I want it for.I'm going to have my 1911 with me deer hunting(along with the rifle)and if I can get a close in shot,under 30yrds, I'm going to open up with the 1911.Or I'll be using it in the 40Super configuration and using a 180gr hp 40cal bullet,haven't decided yet.I'll have to test this bullet compared to the other. Gotta get some of that copper babbit alloy to test for toughness.

[saz]

This has my attention. I would like to see it in a large HP/reversable pin for solids. I have been away from the site for a while, and from what I remember the 2/4 cavity molds usually go for $95/$130, right?

[45 2.1]

How does this work; first you need a minimum number of responses. Then a price and time is set.



Not sure how many are required to move to an active GB or to secure Mihec's interest.


This has me interested, would still like the details as far as HP is concerned (style of HP). I just got done with a GB from NOE so this 1 I'm kinda new at as far as what material the mould is made from, aluminum, brass and so on. Of course price, cavity availability and so on, unless I missed it somewhere.


This has my attention. I would like to see it in a large HP/reversable pin for solids. I have been away from the site for a while, and from what I remember the 2/4 cavity molds usually go for $95/$130, right?

First post has been updated...... take a look......... and this is a brass cramer style mold.

[dutch41]

4 cavity please; large round pin set and blank if needed.

Thanks!

Scott

[hamour]

I am interested in the hollow point and solid molds.

Hank

[45 2.1]

This has gone Active here:

http://castboolits.gunloads.com/showthread.php?p=1682283#post1682283

[wacki]

If it was 230 grain (subsonic) with hollowpoint I'd buy. Not sure 200 grain is heavy enough.