View Full Version : What do I have here?
crabo
02-18-2012, 09:49 PM
I did some trading and came up with a few molds. What do I have here?
Lyman 311410AV 830 2H 2 cavity
Lyman 358091 AV 4 cavity
Lyman 410459 HW 749 BA 2 cavity
Lyman 323470 132 4 cavity
Lyman 12 539 1 cavity 12 g HB Slug
Lyman 20A 688 1 cavity 20 g HB Slug
Lyman 401633BV 153 RA 2 cavity
Lyman 356634AV 870 2H 4 cavity
Lyman 452374EV 2H 4 cavity
Lyman 401638 121 2H 10-97 121 4 cavity
Lyman 401638BV H 4 cavity
Lyman 401638 CV 1212H 4 cavity
H&G 310 4 cavity Ser # 6787 Murphy
RCBS 45-230-RN 2 cavity
Thanks,
That four-cvity 323470 sounds attractive.
runfiverun
02-18-2012, 10:15 PM
http://castpics.net/Lymans/Lymans.htm
craig, look here.
go to references and click on the mold section most appropriate.
Blammer
02-18-2012, 10:39 PM
looks like some fairly good moulds
crabo
02-19-2012, 12:23 AM
Thanks runfiverun. That is a good reference. Any way to find out what they are worth? I may have to buy a couple of guns to use them.
I tried to print that mold chart out and it didn't work, but I found this one that prints well.
http://www.three-peaks.net/bullet_molds.htm
geargnasher
02-19-2012, 12:48 AM
Crabo, what you have there is a bunch of junk. I'll give you scrap steel price for them when you come down to help me finish my house :p
Gear
crabo
02-19-2012, 01:04 AM
Crabo, what you have there is a bunch of junk. I'll give you scrap steel price for them when you come down to help me finish my house :p
Gear
Hold your breath!
geargnasher
02-19-2012, 01:16 AM
Heeheee!!!!!!!! :kidding:
Gear
runfiverun
02-19-2012, 03:46 AM
the 311410 is a 130gr plain base mold could be used in the 30 carbine or make a good low velocity 30 cal rifle mold.
the 358091 is a copy of the H&G #50 i use it in 38 cases in my dan wesson with only the bottom lube groove filled [it likes that lube you sent me btw]
the 410459 is a classic 41 mag keith boolit that you have no use for and need to send to me.
the 323470 is a lightweight 8mm mold i use it in my lebel and it does fair in my model 700 but has to be seated a bit deep for it.
401633 [the last number might be an 8] if it is an 8 it has two weights 175 in plain and 155 in hollow point and is a t/c shape.
the 356634 looks like a 130 gr truncated cone for most likely the 9mm as it has no crimp groove.
452374 is a 180 gr very large hollowpoint for the 45 acp,or a 225 gr [rn ball ammo copy]
the H&G i don't know but the rcbs is definately another 45 acp mold.
i'd say you got some molds from a early 1970's caster as those would be pretty popular calibers at about that time.
except for the 40 cal molds unless he had a 401 [herters] power mag or sumthin.
beagle
02-19-2012, 01:16 PM
According to Tom's list, the 310 H & G is a 125 grain 9mm bullet and should be very useful in a9mm semi-auto./beagle
canyon-ghost
02-19-2012, 01:34 PM
the 410459 is a classic 41 mag keith boolit that you have no use for and need to send to me.
Amen, Lamar!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.