NOE 376 220Gr. FN

[SwedeNelson]

NOE 376 220Gr. FN

Going to CLOSE THIS BUY
moving it up to run with the 35 200Gr. FN (RCBS)
Both use the same tooling / set-up.

http://i69.photobucket.com/albums/i80/swedenelson/1111-199-378220FN.jpg

http://i69.photobucket.com/albums/i80/swedenelson/1111-199-378205FNHP.jpg
We will offer this bullet .376"x .366" nose and .382"x .372" nose diameter

This buy is on the schedule.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
RG2 cavity HP mould $96.00 Ea.
RG4 cavity HP mould $126.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00 Shipping/Handling.
Prices are subject to change at any time.

You can mix number of cavities in an order to make 5.
We will offer plain base (PB) and gas check (GC) in the same blocks.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds

Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289


Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
*1 blaser.306 5 cavity GC .382
*2 376Steyr 5 cavity GC .376
*3 Ramslammer RG4 GC .382
*4 kfarm 3 cavity GC .376
*5 rockrat 5 cavity GC .382
*6 luigi's mongey 5 cavity 2GC 3PB .382
7 Buckshot 3 cavity .382
*8 GL49 5 cavity GC .376
*9 x101airborne RG2 cavity GC .382 drill for probe
*10 redneckdan 5 cavity GC .382
*11 slug RG2 GC extra blank pins .376
*12 Noggin RG4 GC .382
13 rhouser RG4 3GC 1PB .382
14 Spade 3 cavity 2GC 1PB .382
*15 gester01 RG4 cavity PB .376
16 Aaron 5 cavity GC .376
17 jhickdog 3 cavity 1GC 2PB .376
18 Jtaylor1960 2 cavity GC .376
*19 Rattlesnake Charlie RG2 1GC 1PB .376
*20 gldprimr 4 cavity GC .382
*21 fryboy RG4 2GC 2PB .376
*22 Ed K 4 cavity GC .376
23
24

(*) = Paid

Thanks for the orders
Swede Nelson

[Cimarron Red]

Howdy, Swede,

I'm interested in one of these moulds in .382." At this size what would be the diameter of the nose just ahead of the front driving band?

[blaser.306]

Howdy, Swede,

I'm interested in one of these moulds in .382." At this size what would be the diameter of the nose just ahead of the front driving band?

On the interest thread Al. Has it listed as .372 .

[Cimarron Red]

Thanks, Blaser!

[luigi's mongey]

G'day Swede,

could I order a 5 cavity mold:

3 cavity PB / 2 cavity GC .382

cheers

luigi's mongey

[Buckshot]

..............A 3 cav .382" if you please :-)

...............Buckshot

[blaser.306]

Friday bump!

[Ramslammer]

How good will those HP's be?????
Juddy

[blaser.306]

bump for the weekend

[SwedeNelson]

Updated list
Bump

Swede Nelson

[blaser.306]

To the top for another looky!

[GL49]

Any opinions on how this would work in a .375 Winchester Big Bore 94 lever action? Just bought one yesterday and now I need a suitable mould. Thanks.

[blaser.306]

I would think that as long as the overall loaded length is proper ( will feed) It would be fine. Just my opinion however. Others will chime in and have the voice of reason!

[SwedeNelson]

GL49

You would get a COL of about 2.530 with this bullet.
Should work length wise.

Checked list
Bump

Swede Nelson

[GL49]

Swede,
Please sign me up for a 5 cavity GC at .376

[x101airborne]

Well, looks like I may be adding a 375 winny to my collection, so I am in. 382 diamater, 5 cav. 3 plain base, 2 gas checked, HP one of the plain base and drill for probe. x101airborne at yahoo dot com.

[SwedeNelson]

Updated list
Bump

Thanks for the orders
Swede Nelson

[johnny356ER]

I would like to order a 4 cav. 2GC 2PB in the .376 config. please.
Thanks,
johnny

[slug]

Hi Swede:
I'll take an RG 2 cavity HP at .376
Thanks.
Stew

[SwedeNelson]

Updated list
Bump

Thanks
Swede Nelson

[johnny356ER]

Swede,

This was to primarily be used in my 38-55 which I just recently sold, and I am currently in other 375 cal buys that will work in my 375 Ruger and possible future 38-55's, so can you please remove me from this list.

Sorry and Thanks,
johnny

[30calpal]

I'd really like to get in on this one too, but I need a .379 diameter and I'd really prefer something at least 235gr with 2 lube grooves. Marlin 375 barrels seem to slug 377 and a .376 may or may not bump up to fill it. I'll wait and see if there's interest in a GB for .379-235 /245gr-FN /Penta Pt will be offered in the future. [smilie=1:

[Suo Gan]

I'd really like to get in on this one too, but I need a .379 diameter and I'd really prefer something at least 235gr with 2 lube grooves. Marlin 375 barrels seem to slug 377 and a .376 may or may not bump up to fill it. I'll wait and see if there's interest in a GB for .379-235 /245gr-FN /Penta Pt will be offered in the future. [smilie=1:

http://castboolits.gunloads.com/showthread.php?t=131915

Vil dis vuk forju?

[30calpal]

Hey Swede, is this (379-235) GB over? Any chance of reviving the 379-235 RF(RD) GC w/ pins ? I was just directed to a link dating back to 2011 and this bullet is exactly what I'm looking for in my two M375's

[redneckdan]

sign me up for a 5 cavity at .382 if you would.

[SwedeNelson]

Updated list
Bump

Swede Nelson

[bearcove]

Al, Just sold my 38-55 so don't need this one antmore.

Thanks, Rod

[rhouser]

I would like to get in on this if it is still open

I just edited this to change my order preferance.

I would like to order the RG4 cavity HP mould in .382 with 3 GC and 1 PB

I will use the Paypal and understand the surcharge.

Thanks in advance.

rc

[kfarm]

Please put me down for a 3 cavity .379 gas check with HP. I have an original 2 cavity RD mould that with 34gr of 4895 will put 5 shots into 1" @ 100yds with my JES rebored 336.
Just wanting the NOE quality over the Lee.
Carroll

[Noggin]

I am interested in a RG4 GC .382
I can be contacted at iaintrue at hotmail dot com

[SwedeNelson]

Updated list

Bump

Just so we have no misunderstandings this
buy is on the schedule for March 2013


Thanks
Swede Nelson

[Spade]

Hi Swede,
Looks like a good boolit for my marlin, sign me up for a 3 cavity,, 2 GC, 1 PB IN 382''

Cheers mate, Spade.

[Ramslammer]

bump for a great mold

[SwedeNelson]

Updated
Will try to keep all buys current on the schedule:
http://castboolits.gunloads.com/showthread.php?t=142415
If you have questions about our policy you can see it here:
http://castboolits.gunloads.com/showthread.php?t=156593

Bump

Swede Nelson

[Ramslammer]

G'Day
Spade order a RG and smash some hollow points about the Balangalow.
Juddy

[SwedeNelson]

Updated list

Bump

Swede Nelson

[Ramslammer]

G'Day Swede
Are these current buys staying on the active list or will they be dropped if they don't get 15 orders?
Juddy

[SwedeNelson]

Checked list

Bump

Ramslammer
My plan is to run every thing we have buys for.
I don't want to drop anything.

Side note to all:
We are looking at some avenues to increase our production.
We hope to have some good positive news soon.
On the down side this doesn't happen over night.

Thanks
Swede Nelson

[Spade]

Hi Swede,
Could I change my order to an RG4 GC IN .382"
Thanks mate,
Spade

[Ramslammer]

bump
Come on just one more!!!!
Juddy

[doctorggg]

I would like a 4 cavity 2 pb and 2 gc. Not sure of size yet rifle is on it's way.

Thanks,
Gregory

[SwedeNelson]

Updated list

Bump

Thanks for the order
Swede Nelson

[blaser.306]

Al. I will need to modify my order , I need to get the .382" instead of the .376"

[gester01]

Swede
Can I get in on this buy with an order for 1 RG4 HP with PB in .376"? I would like an extra set of blank pins, if possible.

[SwedeNelson]

Updated list

Bump

Thanks
Swede Nelson

[jethunter]

oops, wrong thread....

[gester01]

Swede

Please update my ID:

16 geater01 RG4 cavity PB .376 should be

16 gester01 RG4 cavity PB .376

Thanks again

[Ramslammer]

Bump
Surely there is more 38/55, 375 shooters out there?
Juddy

[SwedeNelson]

Bump

Swede Nelson

[jhickdog]

Swede,

Please add me for a three cavity 220 grn. fn @.376. Two of fb and one gc.

Thank you,
Jim

[Aaron]

Please add me to the list five cavity no hollow point flat nose only

thanks

Aaron

[Aaron]

Please put me down for a five cavity 376

Thanks

Aaron

[SwedeNelson]

Updated list

Bump

Thanks
Swede Nelson

[Ramslammer]

G'Day
Can't believe some of you 38/55 and 375 win shooters haven't jumped on this?????

[gldprimr]

I'll take a 4 cavity GC 376 FN, need to revise this to a 4 cavity .382"x .372" FN GC

[Ramslammer]

Bump for some more interest!

[slug]

Pl. add a set of blank pins if available.

[Rattlesnake Charlie]

I'm in.
RG2 cavity HP mould $96.00
.376"x .366"
Gas check on one cavity and plain base on the other.

[GL49]

Oops, sorry Swede. I need to specify I'd like my mould at .376. Thanks

[x101airborne]

Hey Al.
Could I modify my order to a RG-2 in 382 diameter all gas checked?
I hope this is not an inconvenience.
Thanks!

[jtaylor1960]

I would like one .376 dia. in a 2 cavity gas checked.Thank you.

[SwedeNelson]

Updated List

Bump

Swede Nelson

[SwedeNelson]

Going to CLOSE THIS BUY
moving it up to run with the 35 200Gr. FN (RCBS)
Both use the same tooling / set-up.

Will get out a PM for payment this weekend

Thanks
Swede Nelson

[gester01]

Swede
Before I get too excited about this, when was the PM supposed to be sent? I never noticed it before. I can't see any change on your GB listings and I didn't get anything... so I'll let you tell me about anything new regarding GB 141, the 376-220gr HP bullet mold.

[jtaylor1960]

I"m sorry but I must back out of this buy.I've run into some unexpected expenses that I must take care of.

[fryboy]

i can take someone's place who backed out ( if at all possible ) a rg4 in .376 would be great with 2 plain base and 2 gas checked cavities
ummm i've never done or been in a group buy before as usually they are too far out to know in advance if i'll have the funds in these trying times so i maybe a lil lacking on group buy equitique etc but ... the funds are currently there leaving me to suggest i'll PM you

[doctorggg]

Please remove me from this buy. I'm #16. I just purchased 2 of your 382 235 gr molds from the group buy that just finished and do not need this one.

[doctorggg]

Correction to the last post. I'm #15. Sorry.

[luigi's mongey]

Swede,
will send money by paypal before end of week.

cheers

luigi's mongey

[Noggin]

Hi Swede,

I will send money by paypal before end of next week.


Thanks
Noggin

[Ramslammer]

Swede
I've paid!
Come on Noggin just use your board money lol. Think how them Hogs are gunna like this mold Nog!! Maybe Dooga (Noggins Dad) will buy a .375 now.
Juddy

[Noggin]

Hi Swede,
Just paid via PayPal

Thanks

[SwedeNelson]

Got the .376 ran and will start to ship them over the week-end.
Had some small problems with the GC shank on the .382
need to do a little work on the form tool but should have it back Monday
Will finish then.

Swede Nelson

[kfarm]

Just checking to see if you got my ckeck.
Thanks Carroll

[gester01]

Swede
I can see that just over half on our list have paid, but your 3/29 note said


Got the .376 ran and will start to ship them over the week-end.

Did any of these get mailed? Is there a ball park guesstimate for getting mine, uh any bodies?

[fryboy]

66510
Swede
I can see that just over half on our list have paid, but your 3/29 note said


Did any of these get mailed? Is there a ball park guesstimate for getting mine, uh any bodies?

mine is enroute ( actually out for delivery today and my mail man seems to start late and finish late and the suspense is ummm killin' me :P ) for me fryday delivery is always extra special !!! which means it prolly wont be in my box until tomorrow [doh]


woot the mailman made it ! looks great al ! thank you sir ! ( seems i now have work to do :P )

[SwedeNelson]

gester01

Every one that paid is shipped
And that includes you kfarm

Thanks for the orders
Swede Nelson

[gester01]

Swede
I got it, thanks... looks great!

[redneckdan]

Got the mould yesterday Al. Looks like it will cast some nice bullets. Should put the hurtin for certain on chicken hawks this summer with my JDJ pistola.

[ihmsakiwi]

Hi Swede,
If there are any molds not claimed / paid for / or people backed out, my buddy would be interested in a 5 banger ( or smaller) for his new Seville 375 Supermag.
Peter.

[Noggin]

Swede

Got my mold today thanks, looks bloody excelant can't wait to give it a go

[Ramslammer]

G'Day All
Mine hasn't arrived yet and I'm getting a bit worried. I've got the USPS tracking but it stops a LA so I'll have to get onto Aus Post.
Juddy

[Noggin]

G'Day All
Mine hasn't arrived yet and I'm getting a bit worried. I've got the USPS tracking but it stops a LA so I'll have to get onto Aus Post.
Juddy

Probly not a bad idea Juddy mine turned up on the 15th you should have yours by now.
Noggin

[Ramslammer]

G'Day Noggin
Aus post need Swede to initiate the inquiry as he was the person who sent it. Dave (Luigi's mongey) Spade and you have all got yours and I'm the one who told you to buy them, no mold for me doesn't seem right lol.
Juddy

[Ramslammer]

G'Day All
Whoo Hoo Guess what arrived 5 minutes ago??? Happy as a pig in something. Too bad I have to fly to a meeting with Noggins dad otherwise the pot would be on.
As usual Swede's work is of the highest standard and look like works of art!!
Juddy

[redneckdan]

Finally got around to trying this boolit with 10B101 in my three six bits. Used 20grs with a magnum rifle primer. This group was shot from sitting with a sling at 50 yds.

http://i17.photobucket.com/albums/b77/redneckdan/A28528E2-0830-4637-9F5B-4DBACECE76BD-247-000000541AC79E4E.jpg