View Full Version : Lee -6 Cavity .476-400gr Keith
475/480
02-13-2007, 11:32 AM
This is a test run for the Lee 6 cav-.477-400gr Keith.
We are trying to figure out how many want in on this buy and then I can post a cost per mould.
**OK let's go with .477"**
Spec's-
Size-.477"
Noselength- .406"
Weight w/WW- 400gr
Plain base
Meplate-70%
Thanks Sean
fivegunner
02-13-2007, 05:40 PM
I`ll take two!:Fire:
Lloyd Smale
02-13-2007, 06:25 PM
id take two for sure possibly 3
MGySgt
02-13-2007, 06:46 PM
I'll take 2 - but I wish it was .477 due to Lee being a little undersize.
neerb
02-13-2007, 11:48 PM
yeah I'd be in for 1 and a gas check version when they come around. Thanks Dave
Lloyd Smale
02-14-2007, 06:19 AM
make it 3 and id like to see them drop a little bigger the .476 too.
dubber123
02-15-2007, 07:00 PM
I,d like one also, The nose looks to be the same length as their existing 400 gr. round flatnose, am I correct?
targetshootr
02-15-2007, 09:43 PM
I'd like one and I don't even have a 475.
uncowboy
02-16-2007, 12:53 AM
I want one uncowboyATcomcast.net
475/480
02-16-2007, 08:03 AM
I,d like one also, The nose looks to be the same length as their existing 400 gr. round flatnose, am I correct?
I (think) it is the same ,I dont remember if the Lee FN was .390" or .400" on the noselength.
Sean
dubber123
02-16-2007, 08:23 AM
Thanks, the one I have looks to be .400", I don't have room for much more though, how many people need to go in before the buy takes place?
475/480
02-16-2007, 10:09 AM
Thanks, the one I have looks to be .400", I don't have room for much more though, how many people need to go in before the buy takes place?
The GB will take place, I was just trying to get an idea on total # of moulds this way a price per mould could be set.
Sean
Wildcat
02-16-2007, 11:41 AM
I'm in.
2 dogs
02-16-2007, 04:31 PM
I would like to have one of these molds please.
Mohillbilly
02-17-2007, 11:08 AM
:Fire: Me too
poletax
02-17-2007, 05:33 PM
I'm in.
I'd even like to get one a little heavier.
425-440 grain.
lar45
02-20-2007, 12:28 PM
I'll take one even if we have to pay the extra setup fee.
I will probably need a reminder when you decide to run it.
Thanks.
Mack Heath
02-20-2007, 04:39 PM
You may count me in too. I only need one at the moment, but could go 2 if we were close to making the minimum.
MH
j4570
02-21-2007, 10:53 PM
I have a 480 Ruger barrel for my encore pistol I have never shot.
this looks like a good fit. Anyone with experience with the 480 know if this design is acceptable for this combination?
If so, I'll probably get in on it in a month or two, money tight right now (but 475 bullets are spendy).
JW
allie
02-21-2007, 11:05 PM
Count me in. I need one.
allie
Lloyd Smale
02-22-2007, 10:24 AM
it will make an ideal 480 mold. At that weight its probably even more ideal for the 480 then for the 475 but would make a great bullet for either.
I have a 480 Ruger barrel for my encore pistol I have never shot.
this looks like a good fit. Anyone with experience with the 480 know if this design is acceptable for this combination?
If so, I'll probably get in on it in a month or two, money tight right now (but 475 bullets are spendy).
JW
j4570
02-22-2007, 07:20 PM
Alright,
put me down for one. If I don't remember, please email me.
I wouldn't mind paying a little more to cover the setup fee if we can't get enough to get it free. How many we got to have? 25? or 50?
Thanks
JW
475/480
02-22-2007, 11:06 PM
For NO setup fee- minimum 25
Sean
Alright,
put me down for one. If I don't remember, please email me.
I wouldn't mind paying a little more to cover the setup fee if we can't get enough to get it free. How many we got to have? 25? or 50?
Thanks
JW
fivegunner
02-23-2007, 06:13 AM
are we getting close to placing orders yet? :Fire: :drinks: :-D
Lloyd Smale
02-23-2007, 07:20 AM
if everyone was serious i count 19 so far. Were getting pretty close to the 25 maybe we should let it run a little longer.
Clyde
02-24-2007, 10:05 AM
I will take one...
dubber123
02-26-2007, 07:43 PM
Anyone have a ballpark estimate of when this one will be ready to go? I'm not rushing anyone, I just don't want to get caught on short notice. Thanks.
475/480
02-27-2007, 08:18 AM
Anyone have a ballpark estimate of when this one will be ready to go? I'm not rushing anyone, I just don't want to get caught on short notice. Thanks.
I think Friday 3-2-07 should be good.I will also start a new thread on friday.
Sean
j4570
02-28-2007, 08:50 PM
You'll start a new thread and give us some time to pay I presume, an official group but thread? I like ones that run a month.
Thanks
JW
Bukufungi
03-01-2007, 02:09 AM
I had to join this site just to get one of these...count me in for one! Thanks.
buck1
03-01-2007, 02:38 PM
I will take one!!
475/480
03-01-2007, 04:57 PM
Lets drop this thread,
I started a new thread with the boolit specs and started accepting orders.
Thanks Sean
AaronE
03-22-2007, 03:48 AM
i'm in for one
nyatii
07-11-2007, 09:35 PM
Is the group buy still open for the 6 cavity .476?
Jim Vaughn
Lloyd Smale
07-12-2007, 05:43 AM
this one is allready done but theres another for an lfn starting http://castboolits.gunloads.com/showthread.php?t=17938
buck1
07-20-2007, 12:55 AM
DARN! I thought they were in.. LOL Buck
Bukufungi
08-03-2007, 01:20 AM
Any word on when these will arrive?
475/480
08-03-2007, 08:40 AM
I hope within 2 weeks.
Sean
2 dogs
08-03-2007, 09:41 AM
WOW, Sean thats exciting to me as this will be my first LEE group buy mold of several I have gotten in on! I may even have to kick on my pot in the heat of the South Texas summer to try these boolits out!
buck1
08-09-2007, 10:58 PM
WOW, Sean thats exciting to me as this will be my first LEE group buy mold of several I have gotten in on! I may even have to kick on my pot in the heat of the South Texas summer to try these boolits out!
Not me!! Southern New Mexico / texas heat is killing me as it is!!......Well maybe just a few................................(hundred)...LOL .......Buck
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.