View Full Version : Will this shoot?
Carteach0
12-06-2006, 09:21 PM
I have a Mosin M44 whose bore I have slugged. I mic'ed groove to groove at .315".
The rifleing is strong, with a fair bit of throat errosion.
The closest bullet I can cast is a 186 grain .313 gas checked bullet from a lee mold which I can then size at .313" in my lubrisizer.
One of these pushed into the bore shows a clear and fairly deep rifling imprint
but clearly the wideest dimension of the bullet never even touches the bore.
I'll try it, but I have no high hopes. Is there any chance this will shoot decently?
I was wondering if a higher end charge of rapid powder (red dot maybe?) would upset the bullet enough to seal well.
I am looking for 100 yard accuracy for target and plinking, maybe some small game and wood chuck hunting next summer.
dahermit
12-06-2006, 09:36 PM
I had the same problem with a 38-55 winchester M94. The groove dia. was .379 and the bullets were only .376. I found out that using soft bullets; wheel weights plus 2% tin, not heat treated, pushed faster. They slugged up to fit the bore and I got good accuracy at 100 yards with iron sights. The bullet sizing die I had was .376 also, so it was only lubing the bullet.
I had been trying to shoot hard heat treated bullets, but they would not fill the bore.
You did not mention what alloy you were using.
Regards,
dahermit
Carteach0
12-06-2006, 09:51 PM
I shoot wheel weight with some extra tin added by way of 60/40 solder.
Both air dropped and water dropped. These .313" bullets I have always
water dropped, but I think I will try air dropping for this.
I am also wondering..... perhaps I will try them without the gas check as well.
woody1
12-06-2006, 10:39 PM
I shoot wheel weight with some extra tin added by way of 60/40 solder.
Both air dropped and water dropped. These .313" bullets I have always
water dropped, but I think I will try air dropping for this.
I am also wondering..... perhaps I will try them without the gas check as well.
If you've got any soft(er) lead, like the stick-on wheelweights, I'd add some of that. I'd also leave the gas check on and if I had a larger sizer, I'd put the gas check on and lube with it. You could also try to build up the size a little with Lee Liquid earwax. Regards, Woody
swheeler
12-06-2006, 11:44 PM
Beagle it, the mold that is.
drinks
12-06-2006, 11:52 PM
I had an M-N , M44, .315 groove, did all I could to fit it, even reamed a mold out to .317" and made a sizing die to fit, still got 2 1/2" groups at 25 yds. I solved the problem by finding a pawn shop that would buy it.
:[
mooman76
12-07-2006, 12:50 PM
I have heard of some using the dacron fillers in these cases. They claim they help seal the bore to help them shoot better taking up those few thousands extra space! I have a rifle I've been meaning to try it on. A spanish mauser with an oversized bore of .290. Even jacked bullets shoot bad in it!
singleshotbuff
12-07-2006, 01:22 PM
Carteach,
Have you thought of "patching" the boolit larger with teflon tape? I'm not sure if it would work, but I have read of guys wrapping teflon tape (plumbers tape) around boolits. I don't remember the logic behind it, if it was for improved fit or lubrication, but it may be worth a shot.
SSB
grouch
12-07-2006, 06:24 PM
You could try lyman's 311299(314299?). Mine casts .315+ and may do better than Lee's mold.
PAT303
12-07-2006, 06:49 PM
A friend of mine has the same problem with his nagant,so we cast bullets out of 50/50 ww and lead and loaded them and it worked. 311299 with 25grns off 2207(4198) dacron filler water quenched 2'' groups at 100. worth a try!! Pat
woody1
12-08-2006, 12:27 AM
Beagle it, the mold that is.
Dunno where I was when I posted my answer. Brain fart I guess! Beagling is prob'ly the first thing I'd try and a couple thous. is very doable. I've never done the teflon tape thing but have paper patched boolits for a big bored krag before I had a mould big enough. It worked well, but is a log of work. Regards, Woody
Buckshot
12-08-2006, 03:15 AM
............Does this mean it's time for another FAT 'Fat 30' GB :-)?
..............Buckshot
Sailman
12-08-2006, 03:35 AM
If someone is going to start a Fat-Fat-30-GB project, I would like to purchase one of those molds.
By the way, what does GB mean?
Sailman
By the way, what does GB mean?
Sailman
GB = Group Buy
Robert
texas tenring
12-08-2006, 10:25 AM
I would be interested in a fat 30 group buy for my larger bore mosin's.
yodar
12-14-2006, 06:10 PM
I had an M-N , M44, .315 groove, did all I could to fit it, even reamed a mold out to .317" and made a sizing die to fit, still got 2 1/2" groups at 25 yds. I solved the problem by finding a pawn shop that would buy it.
:[
I had the same problem with needing bigger bullets for my smellies. There is a lyman mould to met my specs but it is (I believe) discontinued 314299 a bigger heavier bullet about 200 gr, is very hard to find, high demand, and accordingly, COSTY
Check this out:
http://www3.sympatico.ca/shooters/castsstory3.htm
I use a Lee 311-155-2R which casts big, some as big as .313, and with a scoop of antimony in my tin-augmented wheelweight metal makes BIGGER bullets when cooled, many of which go up to .315
try it out before risking a mould thru beagling. then if my trick doesnt work, you can grind away in good conscience
yodar
45nut
12-14-2006, 08:24 PM
Yodar,
there is no "grinding" involved in beagling a mold and it is completely reversible.
perhaps a reading of the technique again may be in order....
http://ktsammo.250x.com/castboolits/cst3.html
SharpsShooter
12-14-2006, 08:36 PM
Yodar,
there is no "grinding" involved in beagling a mold and it is completely reversible.
perhaps a reading of the technique again may be in order....
http://ktsammo.250x.com/castboolits/cst3.html
Absolutely correct! I have "Beagled" several moulds with good results, including multiple cavity mopulds. If you are grinding..you ain't Beagling.....you are just grinding.
SS
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.