joeb33050
10-31-2006, 07:14 PM
This is almost a direct quote from Ned's book. I see the problems, but think it's worth printing because it gives the reader a place to start in making cartridges.
I'm looking for help here in editing these and finding my errors.
8.4.13 CARTRIDGES FOR MUZZLE LOADING RIFLES
Ned Roberts
Turn a hardwood cylinder about .012" to .014" smaller than the bore of the rifle and about 6" long.
Roll a piece of wrapping paper about .003" thick and 3.5 inches long around this cylinder and mark the paper where it makes two complete laps. Cut the paper off at this point, unroll it and place it on a piece of tin. Mark the tin and cut the tin to shape to make a tin pattern for cutting the pieces of paper for the cartridges.
Use the tin pattern and a sharp knife to make the papers, six to eight thicknesses of paper can be cut at one time.
Roll a piece of the paper on the cylinder and paste the end down with gum arabic mucilage.
Slip the paper tube off the cylinder and allow it to dry.
After a supply of tubes has been made, slip one over the cylinder nearly to the end.
Place a round ball with the sprue up inside the tube. The tube should extend about 3/8" over the ball.
Twist the end of the tube, tie the end with a white thread and slip the tube with the ball inside off the cylinder.
Place a lubricated, correctly sized felt wad in the tube, over the ball.
Pour a measured charge of powder behind the wad and ball, into the tube, and finish the cartridge by twisting the end of the paper cylinder and tying it with red thread.
Then, with a small brush, apply a light coat of beeswax to the front end of the cartridge in which the ball is held, in order to facilitate loading and take the place of the oiled cloth patch.
When loading, the end that was tied with the red thread is grasped in the teeth, the end of the paper torn off, the powder poured down the bore, and the rest of the cartridge pushed down onto the powder with the ramrod.
When loading these cartridges with the conical bullet for the rifle. the end of the tube was attached with gum arabic mucilage to the base of the bullet and dried with the point of the bullet extending from the tube.
I'm looking for help here in editing these and finding my errors.
8.4.13 CARTRIDGES FOR MUZZLE LOADING RIFLES
Ned Roberts
Turn a hardwood cylinder about .012" to .014" smaller than the bore of the rifle and about 6" long.
Roll a piece of wrapping paper about .003" thick and 3.5 inches long around this cylinder and mark the paper where it makes two complete laps. Cut the paper off at this point, unroll it and place it on a piece of tin. Mark the tin and cut the tin to shape to make a tin pattern for cutting the pieces of paper for the cartridges.
Use the tin pattern and a sharp knife to make the papers, six to eight thicknesses of paper can be cut at one time.
Roll a piece of the paper on the cylinder and paste the end down with gum arabic mucilage.
Slip the paper tube off the cylinder and allow it to dry.
After a supply of tubes has been made, slip one over the cylinder nearly to the end.
Place a round ball with the sprue up inside the tube. The tube should extend about 3/8" over the ball.
Twist the end of the tube, tie the end with a white thread and slip the tube with the ball inside off the cylinder.
Place a lubricated, correctly sized felt wad in the tube, over the ball.
Pour a measured charge of powder behind the wad and ball, into the tube, and finish the cartridge by twisting the end of the paper cylinder and tying it with red thread.
Then, with a small brush, apply a light coat of beeswax to the front end of the cartridge in which the ball is held, in order to facilitate loading and take the place of the oiled cloth patch.
When loading, the end that was tied with the red thread is grasped in the teeth, the end of the paper torn off, the powder poured down the bore, and the rest of the cartridge pushed down onto the powder with the ramrod.
When loading these cartridges with the conical bullet for the rifle. the end of the tube was attached with gum arabic mucilage to the base of the bullet and dried with the point of the bullet extending from the tube.