View Full Version : Casting Equipment
- Lee dripper mod
- Building Bottom Pour Smelting Pot
- Saeco Melting Furnace Metering Valve Question
- Getting a old Lyman up and running
- Need help with RCBS LUBE-A-MATIC® SIZER
- best way to heat a Lyman 45
- .357mag/.38 spl mold and alloy?
- Single burner and 4 gallon pot
- Mold mallet/ Sprue Knocker
- Lyman 356637 147gr mould help
- Best way to get rid of Lyman mould surface Rust?
- current set up for casting
- Broke my 450??
- The biggest cast pot I have ever seen
- saeco sizing die
- Lubrisizer better??
- Lyman furnace question
- Ballist-cast?????
- Lyman MAG 25 first use report
- 35 dollar PID temperature controller build
- My MKV bullet master started doing some interesting things help!
- Hardline and other casting machines
- Lyman 45 part same as 450 or 4500?
- Huge thanks to Buckshot
- A thread for pics of homemade smelting/casting operations... make me drool!
- Lyman 45; Help finding the real parts.
- My Mag-20 element went out again
- Lyman Big Dipper Casting Furnace 110 Volt
- Tools
- Lyman 45?
- RCBS thermometer.
- Lee service excellence
- Kudos to RCBS again
- Manual for a ballista cast mark II
- Lyman 45
- New PID Temperature Controller
- Lee Sizer Sizing Smaller than Previously
- Lyman 450 Heater at Midway
- Hornady Lock-n-load Classic Priming System
- Thinking of stepping up to a lubesizer..... looking for opinions.
- Silicone baking mats
- NOE expanders
- Help Needed W/SAECO Sizer
- Got a mold that has the Spru plate stop is broken
- PID Gurus?
- I'm down with IllinoisCoyoteHunter
- RCBS or Lyman?
- SAECO Lubrisizer - Tips and Lessons Learned
- New smelting pot
- PID question
- RCBS LAM11 O-Rings "FREE"
- Very interesting youtube Video
- mp molds
- Are there any benefits ???
- Magma Bullet Master! (New to me)
- star binding
- Solid Oak Casting Table
- Smokem Joe Bump Die
- Looking for a .380 acp mould
- 354 sizer
- Lube bleed in Star
- Ballistacast Mark II
- Unique Plumbers Furnace resurrected.
- Casting Bench Height
- PID questions
- Cast Aluminum Smelting pot
- Lubemaster with M-A Systems collator
- Saeco furnace value
- Meacham Lube sizer
- Mag 20 spout freeze update
- Thin steel pot for smelting 500lbs at once?
- Need some advice on bullet sizer
- NOE Mold Thermometer?
- .243 bullet molds
- Propane tank base cut off
- smelting pot question ?
- Just got a Lyman Lube Sizer ? ?
- Saeco lube/sizer
- Need help/suggestions for my RCBS Lubsizer 2
- Which sizer for this Eagan die?
- Hotplate for mold heating?
- Which Lube Sizer Dies ?
- What top punch ?
- Getting the size right?
- PID question
- Best flux for pure lead?
- Lee 4-20 and tight wad
- accuratemoulds.com 36-110 B=Lee's 105 swc?
- Mould Master XX
- Suggestion for my new to me 30-06
- Valve guide hone
- Magma Master Caster
- New to casting need advice
- Sizing for PCed bullets
- Which is better 45 or 450???
- 450 Sizing die modification, can this be done?
- how to buy a lubesizer
- Lee 4-20 casting pot help
- Sizing in a LEE backwards
- anyone heard from OBIII lately??
- Lube sizer die dimensions needed
- Caig Melting Bath anyone see one of these?
- Magma Bullet Master Air Cylinders
- Help with a MYPIN TA4 PID
- Anyone using a computer program to track your hobby?
- Is this what I need to build a PID?
- Casting table height?
- Rifle bullets point up orientation using Hornady bullet feeder will work! AS/2 sizer
- Smelter/remelter on Ebay
- MYPIN TA4 PID Help needed
- Upside down press for sizing using Lee sizing die
- Infrared Thermometer
- Stripped threads in RCBS LAM 1
- Mold oven atop a hotplate
- Making a bottom pour pot
- .378 X .381 expander for 38-55, 38-56, 38-72 etc.
- Laser Thermometer is appropiate ?
- PID part shopping info
- Need replacement therostat for Lyman Mag 20 furnace
- elbow pain and ladle pouring
- rcbs lam2 with air feed
- let the smelting begin
- RCBS Pro Melt Upgrades
- Waage K4757 Upgrading My Melter
- Electric Lead Plumber Pot
- Everyone knows it's Windy (cobble wind sheild for Lee 4-20)
- Where to buy custom Lee type sizing dies?
- Dumb question time? Lyman 45
- Cost-Benefit of earlier generations Lyman's, RCBS?
- Have to get some wine and play Barry White (Pro-Melt due on 24 Apr)
- Luberisizer die & top punch
- A Matic feature on RCBS LAM 1
- RCBS Pro-Melt Arrived! (shipped 17th, arrived 20th)
- Rough test of TC's and Laser IR measurements
- Making a pid case
- pot dimensions
- Iron moulds and temperatures
- I'm tired of the bbq burner....what's the next step?
- PID question
- Under pressure! (David Bowie, Pro-Melt, and bottom pour)
- About had it with casting using a gas camp stove. Tiring, frustrating morning.
- .416 mould
- Anyone made their own bullet sizing dies?
- master caster, wtb
- To Flux or not to Flux? That is the question.
- broke handle
- About the way my luck runs
- A pot that will work
- Top punch for Lee 356-102-1R?
- JLD612PID/Lee 4-20
- Magma Bullet Master questions / issues
- A New Way to Keep Lube From Smoking in the Pot
- Vent fan question
- Bottom pour technique from RCBS Cast Bullet Manual
- Lyman mold guide on a Lee pot ?
- Suggested casting temperatures from RCBS Cast Bullet Manual
- Most important piece of Casting Equipment?
- Lee pot, now what?
- RCBS vs LYMAN lube sizers
- H&G 10 Cavity Mold
- Pan or pot for range scrap?
- Why use an SSR when Lee states the Pro 4 20lb pot (100v) only draws 6.36 amps?
- how to get PID probe though new RCBS lid??
- Respirator/face shield/gloves help needed
- Who can make me a leather apron?
- Is it necessary to split the wood dowel when opening up a lee bullet sizing die?
- Non-immersion T/C to control pot temp
- what top punch for a lyman 32/20 mold.
- Upgrade Your Roman Era Casting Technology
- Want to cast 150 gn. bullets for Marlin .30-30 336cs w/microgroove barrel
- Lyman orange?
- Lot of 25 empty propane tanks
- Lymann Sizer Issue
- Picked up a Lyman Mag 25 Digital Furnace today
- Old Lyman Mould Master parts
- PID keeps blowing fuses...
- New (to me) heat source for melting lead
- PID help
- Reducing diameter of cast lead bullet?
- Question About Lyman 450 Lube/sizer?
- my lead recycling setup.
- What dies for this Lube-A-Matic? Pics
- Melt thermometers?
- How to convert Pro Melt to "pull down to open" lever
- Extension cord wire size?
- Be careful of FAKE SSR's not UL rated and they don't hold up
- Converting RCBS Pro Melt to "pull down to open" operations
- Pending Charge on My Credit Card- my Star must be on the way!
- Do you remelt sprues with your PID?
- Any GURU's on REX PID's on here?
- RCBS Pro Melt heating issue , bottom half of pot.
- Email for Magma Engineering?
- Cooper Industrial Flange Mount Stem Thermometer
- another upgrade in equipment
- What lube sizer are these for???
- Lyman Mag 25 Furnace
- How to make my ladle "silky smooth"?
- Frankford platinum case prep and trim system
- RCBS Pro Melt
- How do bottom pour molds work? In this case Saeco
- Ballisti-cast Mark X machine issues.
- Dumb question: Lee push through sizer on an RCBS press, bullet punches?
- Digital Thermometer for Pot and Mold?
- Do you empty furnace after use? Beginner Question of course
- presenting the "star wars imperial walker smelting pot"
- Lyman 4500 lubrisizer threaded rod and plunger removal
- New Lyman mold isn't working so good.
- RCBS LAM11 O-Rings "FREE"
- Starting from scratch: kit or separates?
- Thoughts on filling the pot at the end of a casting session
- Pine "Sawdust" Table saw fine? Chain saw size? Courser OK?
- Electric cord for a Saeco Mod 24 lead furnance
- Dead Lyman lead pot
- Will low level of lead harm lee furnace?
- Dual PID? For mold probe/pre heat/hotplate? Wood enclosure OK?
- Hand Turned Mold Tappers for Sale
- Smelting pot...threads on 20lb propane tank?
- On the PID bandwagon
- RCBS Top Punch
- How many an hour
- Nice inexpensive lead skimmer.
- Problems with old Lube-A-Matic - Newb alert
- Indicator Lights for PID - Which To Get and Connect? Female Plug?
- ways to fuse a PID
- getting ready to start my pid couple of questions.
- Question to those with Lyman dipper
- Wire Size Gauge for PID? Detail I Couldnt Find.
- wooden ingot molds
- Girlfried is pissed and UPS drive was not happy, But who cares
- Lyman universal lube heater dimensions
- Chamber Casting Question for a BSA Martini .310 Cadet
- Lee bottom pour upgrade ;)
- Got one, U better. Collectors item
- Help Wiring PID - wood guy, not good w/wiring
- Lee Lube and Sizing Kit?
- Home made lube heater
- RCBS Lube-A-Matic cold nose muffler?
- Mypin Ta4 PID Exceeds Set Temp, Lee Pot Set to Low or High?
- Old furnace effectiveness
- Lyman pot to rebuild
- Score for me
- Another PID photo/schmatic with couple questions
- Mark-X is up and running
- H&g molds value
- Lyman 4500 on sale..
- Lube heater PID
- top punchs
- Am I OCD
- heating element
- I PIDdled my pots!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.