Ballistic Products has good ones.
For the slugs cut the shell off even with the top of slug and seal with bee wax.
Did I see 44gr blue dot? you are in for a very rough time
Ballistic Products has good ones.
For the slugs cut the shell off even with the top of slug and seal with bee wax.
Did I see 44gr blue dot? you are in for a very rough time
Here you go
http://www.precisionreloading.com/mm...e=ROLL_CRIMPER
As the other guys have stated
The roll crimpers from Precision Reloading are far above the quality of those sold by Balistic Products oor Midway
John
And I carry a LOADED Hell CatYea, thou I walk through the valley of the shadow of death, I will fear no evil; for thou art with me; Thy rod and thy staff, they comfort me.
Hello
I have had a couple of questions about my roll crimpers
One is direct drive
One is double drive
One needs a pulley with handle, mounting bracket and a handle for the other end also
Anyone have a spare pulley?
I think that I may be able to find a handle from a broken Lyman 45 sizer, hopefully.
I can make a bracket from metal.
Thanks
Mike
Wonderful, wonderful, wonderful
I went to Ebay and searched for "Vintage Lyman" many things came up, but one was a Lyman Primer Pocket Reamer.
WELL, I remembered I had one way back in a drawer that I have NEVER used since I use another primer pocket swager.
So, I found it and it had a brad inserted, I sharpened a punch and removed the brad and below is what has happened.
YEEEE HAWWW, I now have the handle that I needed for the crimper.
Still looking for a Browning OK50 pulley.
Mike
Hi,I am raffica.
I am from Italy.
I greet all of you.
I apologize for my English, I use Goole Translator.
I am also Reloader 12 gauge.
Maybe I can be helpful.
I use a Drill Press and an Hard Iron Roll Crimp Tool built here in Italy.
The drill has a mechanical stop so the cartridges are the same height.
The best speed to run the roll crimp with Plastic Hull's is 800-900 rpm, for Paper Hull's is 500 rpm and Roll Crimp Tool is different.
To have a good cartridge is important to close the roll crimp using about 7-8 mm
( 0.275"-0.314")tube free with a Plastic Hull's long 70 mm (2 3/4),wad slightly compressed.
To avoid too much heat on Hull and Roll Crimp Tool Time will be 3-4 seconds max.
I use Silicon Oil and spray inside the Tool every 10-15 crimp, so do not contamine of oil inside the Hull.
I cast Slug and # 00 ,# 3, # 4 Buckshot.
I use Molds LEE (1 Oz), Lyman (525 grain Sabot) and Sharpshooter,Melter Lee Pro 4-20 and Lead Alloy : 3.5% Antimony Rest Lead ,is good.
I hope to be helpful.
Cordiality
raffica
Hello
Welcome to the site.
GREAT post and good english, wonderful
Thank you
Could you post a picture of your hard iron roll crimp tool?
How do you slow down your drill press to 500 rpm?
Thank you
Mike
Precision Reloading is the place to go. I had all kinds of problems until I did as klcarroll posted and purchased the one from them. They also sell a plastic roll crimper for paper hulls that is great also. Skeettex, Drill press belt gearing is the same as you have shown and is very fast to change to a slower speed to roll crimp. My bench top has 6 speeds. If you are good with the trigger finger you can make a 1/2 in Dewalt work pretty good . Not as fast as the drill press though. Since buying my crimper from Precision Reloading my Mec Sizemaster crimp stage is full of dust.
Shooter of the "HOLY BLACK" SASS 81802 AKA FAIRSHAKE; NRA ; BOLD; WARTHOG;Deadwood Marshal;Bayou Bounty Hunter; So That his place shall never be with those cold and timid souls who neither know victory nor defeat; 44 WCF filled to the top, 210 gr. bullet
Thank's Mike
My Drill Press have only 900 rpm.
I use only Plastic Hull and has 4 tools.
These are my Hard Iron Roll Crimp Tool( from left to right):
- Roll Crimp Tool ( wehn I use overshot disc,the central plane is convex to avoid damaging the disc)
- Roll Crimp Tool (specific to Slug)
- Roll Crimp Tool to finish the Star Crimp( the central plane is flat )
- Star crimp Tool ( 6 segments)
Last edited by raffica; 05-02-2010 at 04:33 AM.
My Drill Press .
This is a Prototype, soon time will build the Improved Version.
WOW!!! I really like your roll crimping press !! Wonderful.
Thanks for the pictures
What gauges of roll crimping heads are available?
I also load for 24 and 32 gauge
Mike
It appears that this piece of equipment has a Lee press base and then some very good machine work to complete the equipment.
Shooter of the "HOLY BLACK" SASS 81802 AKA FAIRSHAKE; NRA ; BOLD; WARTHOG;Deadwood Marshal;Bayou Bounty Hunter; So That his place shall never be with those cold and timid souls who neither know victory nor defeat; 44 WCF filled to the top, 210 gr. bullet
Once again, wonderful, I like the length stop idea.
What motor system did you use to power the roll crimp head?
Thanks
Mike
Hello
Yes you understood the question
Thanks for the answer
Mike
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |