Does adding Tin or Antimony increase or decrease the molded diameter of cast boolits. I have mixed up some high Tin casting Lead and all my boolits come out of the mold at least .003 larger than the mold cavities.
ACC
Does adding Tin or Antimony increase or decrease the molded diameter of cast boolits. I have mixed up some high Tin casting Lead and all my boolits come out of the mold at least .003 larger than the mold cavities.
ACC
Both tin and antimony cause an increase in diameter, but the increase isn't much less with tin than it is with antimony. Pure lead produces the smallest diameter.
0.003" larger than the mold cavities themselves or 0.003" larger than boolits cast from pure lead or a low tin alloy?
I don't see how a boolit can be larger than the cavity it was cast in. Are you using Cerrosafe for a casting alloy?
ACC’s alloy surely gives a bullet that shrinks to under the mold cavity diameter, but perhaps the mold maker’s alloy shrinks .003” more, so maybe ACC means .003” bigger than the advertised nominal cast diameter?
Lyman #2 is the benchmark.
It is what the mold makers use to determine the size and weight of dropped boolits.
Any variation from that recipe gives different size & weights.
For example:
I cast a much softer boolit out of a .45 405 gr. Iron mold. Mine come out at 424gr.
In school: We learn lessons, and are given tests.
In life: We are given tests, and learn lessons.
OK People. Enough of this idle chit-chat.
This ain't your Grandma's sewing circle.
EVERYONE!
Back to your oars. The Captain wants to waterski.
+1 Tin added to pure lead assists with achieving a consistent 100% fill of the cavity.The bullets cast with tin, cast larger than bullets cast with pure lead because of the cavity fill out, only. The effect of adding tin levels off at higher % of tin and 2% is about the biggest bang for the buck in that alloy process of lead and tin alloy only. Truly a process of demising return, to keep adding tin by percentage. To get better consistency, more hardness, more velocity, etc., you can add antimony and arsenic to the lead/tin alloy.
“There is a remedy for all things, save death.“
Cervantes
“Never give up, never quit.”
Robert Rogers
Roger’s Rangers
There are three kinds of men. The one that learns by reading. The few who learn by observation. The rest of them have to pee on the electric fence for themselves.
Will Rogers
Opps.
I never could find exactly what RCBS uses, but just figured they went along with the program Lyman had established.
Thanks for pointing that out. .... I learn something new every day.
In school: We learn lessons, and are given tests.
In life: We are given tests, and learn lessons.
OK People. Enough of this idle chit-chat.
This ain't your Grandma's sewing circle.
EVERYONE!
Back to your oars. The Captain wants to waterski.
Lead shrinks when it cools. Tin and antimony don’t. The more of them you use the less shrinkage you have and better fill out.
I thought it was just a less dense alloy than pure lead?
Certainly I’ve read the rest is true: better fill out, which tops out at around 2% Sn, and better hardening effect (and cheaper to boot) from Sb and As than Sn. And I’ve also heard that Lyman #2, at 5% each Sn and Sb is favored not only for its hardness, but also its ductility, a result of the amount of balanced Sb/Sn in the alloy, so tin over 2% is useful in some situations.
Molds are designed around a specific alloy. Going more lead or more tin will change weight & as cast size.
EVERY GOOD SHOOTER NEEDS TO BE A HANDLOADER.
NRA Cert. Inst. Met. Reloading & Basic Pistol
I believe this subject is exactly why casters often complain about molds throwing too small of boolits. I prefer Lyman#2 (at least my alloy version of it) for all rifle shooting. Is it necessary, no but just my preference. Anyway, I often (and usually cheap) will pick up molds that the previous owner says "casts too small". Most of the time, they are just fine with a harder alloy.
Semper Fi
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |