Sportsmans outdoor superstore has Rossi 92 's for sale for $609. Looks like 44 mag and 45 colt
Sportsmans outdoor superstore has Rossi 92 's for sale for $609. Looks like 44 mag and 45 colt
I'm not sure how complicated it might actually be, but I've thought more than once about how a '92 Rossi in .357 Bain & Davis might be received. For readers not familiar with the round, it is a .44 Magnum case, necked down to .357". The hope was to obtain/exceed the original advertised ballistics of the .357 Magnum cartridge, for use in large-frame revolvers and T-C Contenders. Like another "here and gone" high(er)-pressure bottle-necked revolver round I remember, the B&D seemed to work fairly well in Single-Action platforms, but less so in D-A revolvers. Case taper plus high pressures translated to case "set back" that was enough to make smooth cylinder rotation all but impossible after 3-5 rounds.
For obvious reasons, the same operation problems would not be an issue in a lever-action carbine. Just thinking aloud, for now...
For in much wisdom is much grief: and he that increaseth knowledge increaseth sorrow. Ecclesiastes 1:18
He that troubleth his own house shall inherit the wind: and the fool become servant to the wise of heart. Proverbs 11:29
...Verily I say unto you, Inasmuch as ye have done it unto one of the least of my brethren, ye have done it unto me. Matthew 25:40
Carpe SCOTCH!
Rossi makes two sizes of 92's the 357 and the 44 & 45. You would be looking at a custom barrel with a larger thread than the current 357. Then adapt it for the tube feed to hang from.
Last edited by MT Gianni; 11-29-2022 at 04:16 PM. Reason: brain dead fat fingering
[The Montana Gianni] Front sight and squeeze
OP was for 92, MT Gianni mentioned 94. Does Rossi make both in .357 and .44/.45 sizes? I've not looked at them in years, but would be interested in 92 version in .44. If they do make both, is one preferable over the other?
Last edited by Pereira; 11-28-2022 at 08:33 PM. Reason: Spellin
Monte Walsh "You have No idea how little I care".
If they offered it in 44-40, I'd be interested.
Sent from my SM-A716U using Tapatalk
Rossi doesn’t make 94’s. That aside, given the same caliber and a choice between a 92 or 94, I’d go the 92. The 92 is inherently stronger due to the two locking lugs either side of the bolt as opposed to a small block at the back end of a 94. Having said that, I wouldn’t have a Rossi again. I had a bad experience with a lemon and they wouldn’t do anything about it. Wouldn’t feed and also left the factory with a forearm that was gouged clear through between the barrel and feed tube.
They used to make a .44-40 and I had one 25 or so years ago. Sold it to a "friend" at a cowboy club, he never came back and I was never paid. I'd like to have the rifle to shoot BP. It was a half octagon half round rifle length barrel. At that time there was no ammo available, and brass was as hard to find as most calibers are now. Eventually, Starline started making it along with .38-40. GF
Rossi makes the 92 in .357, .44, .45 Colt. I'm pretty sure they even made it in .454 Casull for a short time.
I also have had bad experiences with Rossi, just lately. I got a stainless .357, and fired 5 rounds through it before I noticed that the brass was pretty heavily bulged down just above the base. It appears that the chamber was very sloppily cut. I sent it back, and waited for a couple of months for a replacement barrel, to be finally told that they don't make the stainless anymore. They offered to replace mine with a blued version, and I agreed. (not much choice) I was then told they would order it, and let me know when it was ready to ship to my FFL. Almost a month later, it arrived. It had the same problem, to a slightly lesser degree than the first one. Low pressure .357's would fire with no issues, and .38's would fire with no bulging issues at all.... but full house .357's showed bulges.
I also have a blued .45 Colt version that shows bulges with anything more than "cowboy" loads.
I'm done with Rossi 92's... I love the looks and functioning of them, but it appears they have serious issues with chambering.
I've bought six of the new Rossi's built by cbc, two .45's and four .357's. no problems with any of them.
Only a fool would attempt it, and God help me I am that fool.
Yes, so did I. Once I went through the necessary fitting & polishing and tuning, it was a great little accurate carbine. A CAS buddy offered twice what I paid($400!) so in the interest of groceries/ bills- it went where ever it ended up.....
I've also had 3 .357 Rossi carbines over time. They all needed feeding help, but shot very well.
Sent from my SM-A716U using Tapatalk
I'm glad to hear that everyone has had good luck with their Rossi's... like I said, I really like the looks and function.... I just don't want to buy a rifle and have to shoot puffball loads in it if I want to have reloadable brass afterward.
I shot the 45 Rossi today, with S&B cowboy loads in it, with no issues at all. They chrono'd at almost 1100 fps. I plan to work up a load with a 250-ish cast bullet at around 1200-1250 (rifle velocities). That should thump anything that I will be shooting at... hogs, deer, horse apples.... I can live with that.
The 357's were disappointing.... I now own a Henry side gate 357, 16"... and it doesn't bulge brass on full house 357 loads. Life is good.
Bought a 357 and a 45 colt in the last 2 yrs, they're fine.
Yes, they function wonderfully... at least the three I've bought in the past 5 months have. I just had bad luck with sloppy chambers in the .357's... they would be great for someone that doesn't reload, or just wants to shoot 38 special level loads.
As a visual aid, these are pics of 4 from the first 357, and 5 from the second 357...
Oh yeah, I'd be upset about that. That's sloppiness.
Sent from my SM-A716U using Tapatalk
yep ! they definitely done that wrong.
If I was getting a Rossi - I would buy a 44mag - get the chamber recut to 44/40 - (a clever gunsmith might even be able to do that by hand without pulling the barrel) - the 44mag chamber would be a bit fuller at the front end and that would allow fat cast projectiles in the thinner 44/40 brass - done carefully this should work pretty darn nice .
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |