Has anyone bought 410 dies for standard 7/8” thread of rifle press? Thinking about buying a set. I guess all they really do is resize brass and re crimp.
Has anyone bought 410 dies for standard 7/8” thread of rifle press? Thinking about buying a set. I guess all they really do is resize brass and re crimp.
Quis Quis Quis, Quis Liberat Canes
/////////BREAKING NEWS////////////
Millions and millions of American shooters and sportsmen got up, went to work, contributed to society in useful and meaningful ways all over the nation and shot no one today! How do they controll themselves?? Experts Baffled....
I LIKE IKE
That could be a nice project for someone with the ability to do steel work , a 3 die set would make me pull out my old Lee 3 hole turret press . Size die , precrimp die , final crimp die - just deprime and prime off press .
I would have to look it up, but I think it was a 45 colt sizing die that works perfect with .410.
Any shotgun die sets I have seen for sale, used, were more than you could get a used MEC press for. A 3-die set for around $50 would sell like hot cakes.
O yes I would love to have a 3 die set that screws into a regular press the precrimp and final crimp die could be made to be adjustable 2 1/2 or 3 inch just like a seating die . Lee could be all over this with a limited run every year or so .
I would just want a sizing die. But they would make money on a three die set from me.
You can use pretty much any of the 45 pistol dies for sizing , IF , the case can pass through .
Turn a rod for any of the universal decapping dies , then you just have to get that 209 out through the Colts or 45 S&W shell holder . Then you have to get it back in .
Crimp can be started manually but roll crimp is so much easier .
In the end this is why we like brass 410s .
9.3-74 is still cheaper that 410 cases and is almost full camber length in a 3" . 2.75 I think .
460 brass is only 1.8 .
303 B is 2.1
30-40 Krag comes out 2.15
444 Marlin .
In the time of darkest defeat,our victory may be nearest. Wm. McKinley.
I was young and stupid then I'm older now. Me 1992 .
Richard Lee Hart 6/29/39-7/25/18
Without trial we cannot learn and grow . It is through our stuggles that we become stronger .
Brother I'm going to be Pythagerus , DiVinci , and Atlas all rolled into one soon .
I use an old rcbs 45acp sizer die ( the early one that only sized ) for sizing 444Marlin brass. I suppose it would work for plastic shells as well.
Here is some in either 2.5 or 3". They are like the Lee whack a mole I believe.
http://pacotools.com/order_form
The set I herd about was a two die set, G&H maybe? It has 7/8” threads. Made for plastic hulls. I think Lee had a 410 loader at one time. With the new interest in 410s you would think they would make their Load All in 410. I don’t load shot shells but I do have a 12g load all and a roll crimp for drill press. I only have used it to make some super turkey loads and such but it doesn’t do bad for a cheap outfit.
I've only seen 7/8 NC 12ga dies by RCBS and I think a 20ga set but $$$. Never heard of the smaller gauges.
You might want to check C&H dies out.
Here ya go, http://www.ch4d.com/products/dies/ca...ber&filter=410
Your Welcome.
(740) 397-7214
Just got off the phone with Denny. They are out of stock at the moment but a run is schedualed for December, this year. Go ahead and place a back order now for this year's stocking stuffer for yourself. If you miss this production run which will be orders pending and what they believe i'll get them through two years of sales based on previous SWAG, once they decide to make another run it will be a 24 month wait in the que.
2 die set (FL sizer and seater) $110.
Shell holder (Does not specify rim dia. $11.68
Last edited by Greg S; 05-27-2020 at 03:21 PM. Reason: Additional Info to Add:
I use the following dies for reloading Magtech .410 brass cases:
Lyman 45 ACP carbide sizing die
CH4D # 19 shell holder
Lyman 45 ACP taper Crimp Die
God Bless ya'll
Greg
Je suis Charlie
"You can observe a lot by watching."- Yogi Berra
Shooters Talk Refugee
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |