You could always start one. We exchanged some brass in the current box.
You could always start one. We exchanged some brass in the current box.
One round at a time.
Member of the NRA,GOA and FAOC. Gun clubs Zerby rod and gun club. Keystone Fish and Game Association.
I was thinking a brass and bullet swap box. Each bag of brass should have a note with origin and info such as range brass or times fired. And each bullet bag should contain any pertinant info like alloy, size and lube.
Bazoo
Thank you for the Box.
I like the Brass Box Idea; got a gallon paint can nearly full of .243, mostly once fired, a few have been deprimed, some primed. They need a new home, my brother in law ended up with the rifle. Perhaps we could meet half way if you decide to start The Brass PIF Box. I could donate the 243, we might have coffee or lunch. I'm about 2hrs from Etown.
The I Could Use It box is inventoried, swapped out stuff, & ready to tape up again for the next candidate.
The first person to reply here on the thread will be shipped to when I get their address via PM.
I removed from the box:
B-Square “No Gun Smith” scope mount for 1911
large priming punch for Lyman Truline press
22 tip off rings, med/high
4 M1 Garand clips
1 steel hex rod for 8-32 threaded cleaning and brass prep supplies to a drill without damaging threads.
2x 5.56 repack ammo boxes
Lee .357 bullet sizing die - no pushing rod, just the sizing body(HOOHAA I got a 310 push rod for this)
New bore snakes. 22 cal rifle. 44-45,9mm-357 pistol
30 bore snake gently used
5 380 repack boxes
Green powder coat
Lee 10 lbs bottom pour melter
28-300 winchester mag brass.
30-300 B/0 brass.
Inventory:
B-Square “No gun smith” scope mount for Ruger 22 pistol with bull barrel
Volquartsen comp for Ruger 22 Pistol with bull barrel
Ruger MKII 22 pistol factory grips
Pachmayr grips for Ruger Red Hawk
Lyman 350 ball mould (missing sprue plate washer)
Weatherby 270 weatherby die set new
Lee .41 LC case trimmer pilot and shell holder
RCBS bench primer handle
RCBS .221 Rem die set no box (Repackaged in new ziplock)
11 rd Norma 6.5 Jap brass
1 lithium ion rechargeable 123a battery and charger
Lyman #55 powder drop tubes - 4 pcs (Repackaged in new ziplock)
Lyman TL JR 6MM 2 die set (Repackaged in new ziplock)
Red gun lock
20 pcs. 450 Marlin brass, Hornady head stamp
25 pcs. 458 Socom brass
4 M1 Garand clips
20+ stripper clips 223 for ar mags.
7.62x54 stuck case remover
Uncle Mike's #36 IWB holster. Lightly used.
1 steel hex rods for 8-32 threaded cleaning and brass prep supplies to a drill without damaging threads.
3- 5.56 repack ammo boxes
10x 45acp repack ammo boxes
Remington choke wrench for 12, 16, and 20
AR carbine handguard w/heat shields (Note: Ruger comp & AR flash hider packed in here)
AR aluminum cocking handle found in box
Lee 6.5x284 case length gauge for trimmer
2x Lee old style round primer trays for presses or hand primers
Internal caliper
New bore snakes. 50 cal rifle, 38 ect.
100 .490 caliber traditions musket balls
33 6.5 creedmoor brass.
40 7.62x51 brass.
AR flash hider
I added to the box for the next person:
MTM digital scale; needs battery( watch style)
Lyman Powder Dribbler
TC shot 357 capsules with shot in factory box (50 I think)
Speer shot capsules 357 empty in factory box (50 I think)
20ea-.321 Commercial cast boolits @ 165g
CVA Scope mount for BP rifle NIB
S&W knife lockback NIB
5ea Fluke P/T Chart of refrigerants (all of them) pressures & temps
(Please one each to a delivery as these are handy)
10ea Starrett Decimal tap&drill cards 10ea, Metric tap/drill cards
(Please one each to a delivery as these are handy)
20-170g .321 cast boolits sized w/ gas check,
These will probably not be good in 8mm, fine for 32Win or 32Rem
Lee 270 Hand Case Trimmer
Ironsighter mount for Remington 760-742 rifles
1911 Spur grip safety from Springfield Armory 45
Last edited by PHyrbird; 07-27-2019 at 10:06 PM.
PM Sent.
"Adults are the children and the children are the adults" Jules my wife.
All you need for happiness is a good gun, a good horse, and a good wife. — Daniel Boone
Democracy is defended in 3 stages: Ballot Box, Jury Box, Cartridge Box. — Ambrose Bierce
A system of licensing and registration is the perfect device to deny gun ownership to the bourgeoisie. — Vladimir Ilyich Lenin
Black Rifles Matter
NRA Life Member, SAF Member, GOA Member, TFA Member
Awesome glad to see the box is on the move again.
One round at a time.
Member of the NRA,GOA and FAOC. Gun clubs Zerby rod and gun club. Keystone Fish and Game Association.
Box will be off to Tom Aka Cheeto303, enjoy!!
Carl
Thank you so much Carl. Tom.
"Adults are the children and the children are the adults" Jules my wife.
All you need for happiness is a good gun, a good horse, and a good wife. — Daniel Boone
Democracy is defended in 3 stages: Ballot Box, Jury Box, Cartridge Box. — Ambrose Bierce
A system of licensing and registration is the perfect device to deny gun ownership to the bourgeoisie. — Vladimir Ilyich Lenin
Black Rifles Matter
NRA Life Member, SAF Member, GOA Member, TFA Member
Tom,
U got PM about delivery.
That handle looking thing is not an ar15 charging handle. It looks like a reverse handle off a shifter to me. I forgot to list it.
Box is off to Tom this AM
Sorry, I've been away the last 4 days. I will go thru the box Monday 8/5 and re- inventory it. I will list what I kept and added. Hopefully I'll have it ready Monday evening.
"Adults are the children and the children are the adults" Jules my wife.
All you need for happiness is a good gun, a good horse, and a good wife. — Daniel Boone
Democracy is defended in 3 stages: Ballot Box, Jury Box, Cartridge Box. — Ambrose Bierce
A system of licensing and registration is the perfect device to deny gun ownership to the bourgeoisie. — Vladimir Ilyich Lenin
Black Rifles Matter
NRA Life Member, SAF Member, GOA Member, TFA Member
The I Could Use It box is inventoried, swapped out stuff, & ready to tape up again for the next candidate.
The first person to reply here on the thread will be shipped to when I get their address via PM.
I removed from the box:
Lyman Powder Dribbler
TC shot 357 capsules with shot in factory box (50 I think)
Speer shot capsules 357 empty in factory box (50 I think)
S&W knife lockback NIB
1ea Starrett Decimal tap&drill cards 10ea, Metric tap/drill cards
Lee 270 Hand Case Trimmer
40 7.62x51 brass.
AR flash hider
2x Lee old style round primer trays for presses or hand primers
Internal caliper
New bore snakes. 50 cal rifle, 41cal
100 .490 caliber traditions musket balls
Remington choke wrench for 12, 16, and 20
4 M1 Garand clips
20+ stripper clips 223 for ar mags.
7.62x54 stuck case remover
11 rd Norma 6.5 Jap brass
Lyman 350 ball mould (missing sprue plate washer)
Inventory:
B-Square “No gun smith” scope mount for Ruger 22 pistol with bull barrel
Volquartsen comp for Ruger 22 Pistol with bull barrel
Ruger MKII 22 pistol factory grips
Pachmayr grips for Ruger Red Hawk
Weatherby 270 weatherby die set new
Lee .41 LC case trimmer pilot and shell holder
RCBS bench primer handle
RCBS .221 Rem die set no box (Repackaged in new ziplock)
1 lithium ion rechargeable 123a battery and charger
Lyman #55 powder drop tubes - 4 pcs (Repackaged in new ziplock)
Lyman TL JR 6MM 2 die set (Repackaged in new ziplock)
Red gun lock
20 pcs. 450 Marlin brass, Hornady head stamp
25 pcs. 458 Socom brass
Uncle Mike's #36 IWB holster. Lightly used.
1 steel hex rods for 8-32 threaded cleaning and brass prep supplies to a drill without damaging threads.
3- 5.56 repack ammo boxes
10x 45acp repack ammo boxes
AR carbine handguard w/heat shields (Note: Ruger comp & AR flash hider packed in here)
AR aluminum cocking handle found in box
Lee 6.5x284 case length gauge for trimmer
MTM digital scale; needs battery( watch style)
VA Scope mount for BP rifle NIB
5ea Fluke P/T Chart of refrigerants (all of them) pressures & temps
(Please one each to a delivery as these are handy)
10ea Starrett Decimal tap&drill cards 10ea, Metric tap/drill cards
(Please one each to a delivery as these are handy)
Ironsighter mount for Remington 760-742 rifles
1911 Spur grip safety from Springfield Armory 45
20ea-.321 Commercial cast boolits @ 165g
20-170g .321 cast boolits sized w/ gas check,
I added to the box for the next person:
458 SOCOM once fired 62 peices
6.8 SPC once fired 53 peices
480 Ruger 6 peices
7mm Rem Ultra Max 2 peices
Protech holster for Glock 23,30,36 (New)
Viking Tactics Quick adjust sling MKI (New)
Uncle Mikes #13 Large scoped revolver holster
Protech Large revolver holster
Lee 300 Savage case trimmer pilot and shell holder
AR Riser
"Adults are the children and the children are the adults" Jules my wife.
All you need for happiness is a good gun, a good horse, and a good wife. — Daniel Boone
Democracy is defended in 3 stages: Ballot Box, Jury Box, Cartridge Box. — Ambrose Bierce
A system of licensing and registration is the perfect device to deny gun ownership to the bourgeoisie. — Vladimir Ilyich Lenin
Black Rifles Matter
NRA Life Member, SAF Member, GOA Member, TFA Member
I could use it!
Need a update on this box. Been 11 days.
I've got the box, I'm repacking it right now. I just need to add my items.
the box is taped up and ready to go.
What I took:
1 steel hex rods for 8-32 threaded cleaning and brass prep supplies to a drill without damaging threads.
Ruger MKII 22 pistol factory grips
1 Starrett Decimal tap/drill card
1 Starrett Metric tap/drill card
31 6.5 creedmoor brass
25 .458 Socom brass
62 .458 SOCOM once fired
6 .480 Ruger
2 7mm Rem Ultra Max cases
Inventory:
B-Square “No gun smith” scope mount for Ruger 22 pistol with bull barrel
Volquartsen comp for Ruger 22 Pistol with bull barrel
Pachmayr grips for Ruger Red Hawk
Weatherby 270 weatherby die set new
Lee .41 LC case trimmer pilot and shell holder
RCBS bench primer handle
RCBS .221 Rem die set no box (Repackaged in new ziplock)
1 lithium ion rechargeable 123a battery and charger
Lyman #55 powder drop tubes - 4 pcs (Repackaged in new ziplock)
Lyman TL JR 6MM 2 die set (Repackaged in new ziplock)
Red gun lock
20 pcs. 450 Marlin brass, Hornady head stamp
Uncle Mike's #36 IWB holster. Lightly used.
3- 5.56 repack ammo boxes
10x 45acp repack ammo boxes
AR carbine handguard w/heat shields (Note: Ruger comp & AR flash hider packed in here)
AR aluminum cocking handle found in box
Lee 6.5x284 case length gauge for trimmer
MTM digital scale; needs battery( watch style)
VA Scope mount for BP rifle NIB
5ea Fluke P/T Chart of refrigerants (all of them) pressures & temps
(Please one each to a delivery as these are handy)
9ea Starrett Decimal tap&drill cards
9ea, Metric tap/drill cards
(Please one each to a delivery as these are handy)
Ironsighter mount for Remington 760-742 rifles
1911 Spur grip safety from Springfield Armory 45
20ea-.321 Commercial cast boolits @ 165g
20-170g .321 cast boolits sized w/ gas check,
53 pieces 6.8 SPC once fired
Protech holster for Glock 23,30,36 (New)
Viking Tactics Quick adjust sling MKI (New)
Uncle Mikes #13 Large scoped revolver holster
Protech Large revolver holster
Lee 300 Savage case trimmer pilot and shell holder
AR Riser
what I added:
2 US Constitution booklets
50 5.7x28 cases; once fired (do not clean - lacquer coating)
10 .454 Casull cases; once fired (4 nickle, 6 brass)
50 .50AE cases; once fired (nickle)
20 .308 cases; once fired
20 300blk cases; new Gemtech
15 .45 Cowboy cases; new Starline (rimmed 45ACP)
50 22 cal. hornady gas checks
50 30 cal. hornady gas checks
10 32 cal. lead ball (.315) (for slugging?)
10 36 cal. lead ball (.375) (for slugging?)
10 50 cal. lead ball (.490) (for slugging?)
Last edited by thraxx; 08-23-2019 at 12:17 PM.
Good idea on the lead balls. Those would be handy.
Sent from my LGLS991 using Tapatalk
It’s been awhile. This I can use it box is ready.
The I could use it box has been ready for a month. Surely someone could use what’s in it and add what you don’t need.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |