My feedback page if you feel inclined to add:
http://castboolits.gunloads.com/show...raight-Shooter
Thanks Yall!
Loaded some step loads for 223 to make up some 22 mag or less loads but I don't think I can get there the 225-37 NOE ...........
Knocked out some loads that should be subs in the 1895 .......... Not having much luck with that ..........
Super heavy weights didn't work out in the Colts rifle any better so I don't guess I should be surprised .
It's 95° now so maybe when the sun gets behind the hill I'll go try these . I'd hate to have a load get stale .
In the time of darkest defeat,our victory may be nearest. Wm. McKinley.
I was young and stupid then I'm older now. Me 1992 .
Richard Lee Hart 6/29/39-7/25/18
Without trial we cannot learn and grow . It is through our stuggles that we become stronger .
Brother I'm going to be Pythagerus , DiVinci , and Atlas all rolled into one soon .
Tomorrow is here and just finished smelting 215 lbs of free pure lead in to ingots. That was a bit of work.
Loaded 50 pounds of shot into shotshells for a few weeks fun
Mike
Last edited by skeettx; 08-19-2017 at 11:47 PM.
Busy day for me.
- Decapped and wet tumbled 550+ pieces of 308 brass.
- Sized 1,500 pieces of 300 Blackout and wet tumbled half of 'em.
- Sorted half of a 5 gallon bucket of brass that I bought. LOTS of 44 SPL/Mag in there.
Spent a lot of time working with the the Lee 358-158-RF mold I used making the ugly boolits. The mold release was cleaned out of the mold and then I scrubbed it with Dawn and hot water followed by a final cleaning with lacquer thinner to remove the remaining bits of mold release. I went over the edges of the troublesome cavities that prompted me to use the mold release to begin with. I found a few burrs and scraped them off. The mold still needs a whack or two on the hinge bolt at times but it's much better. I slowed the pace, lowered the melt temperature and went from the ugliest boolits I think I've ever cast to nice ones.
Sometimes life taps you on the shoulder and reminds you it's a one way street. Jim Morris
just finished turning 300 40S&W brass into 250grn 44mag proj.
Yeah...thought you knew...http://castboolits.gunloads.com/show...n-Sizing-Press
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
These HP's have their cavities filled with silicone white caulk to act as penetrator tips, non clogging HP's...
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
I might have to try that!
Wouldn't you think the hard HP would cause more trauma trying to tear through soft flesh?
I keep think of slapping my mouth with the flat part of my hand and hearing a pop and multiplying it by a thousand.
Maybe I'll superglue a airsoft BB like originally planed.
The other thought I had was like the movie "the bear" where one of the hunters made an "x" with a knife, I believe it was a 35 Rem, to get it to expand quicker. I would think that would make a harder boolit fragment with similar results as a nosler partition.
BTW...how many more posts till I get my 1st boolit?
Last edited by Tripplebeards; 08-19-2017 at 11:18 PM.
1000 post per boolit
So you have 1000-390 = 610 more posts till you get
your 1st boolit
Mike
NRA Benefactor 2004 USAF RET 1971-95
I think the silver ones are @ 1,000 posts and gold @ 5,000...not sure.
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
Well, not exactly today, but I finished it off today, 56 pounds of 9mm brass run through my roll sizer, and it is not automated. Worst part it's not my brass, belongs to a reloading buddy of mine.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |