Great pics and report. Thanks.
Great pics and report. Thanks.
I won an Mossberg o/u in a raffle and subbed a Henry steel .357 plus cash(dealer charged $700. for the Henry). I would second the OP's evaluation. I was very disappointed in the barrel finish, looked like it was taken off the lathe and blued! Mine had ejector problems(very weak,some didn't clear) and if it had shot better I would have had Henry correct it. The gun was not as accurate as my two Rossi's but not inaccurate so I sold it. I had hoped it would shoot well due to my experience with their .22's but it was not to be. Also the Henry is about a pound heavier than comparable 92's.
"Masculine republics give way to feminine democracies, and feminine democracies give way to tyrannies.” Aristotle
Loaded up some Laser Cast .412 215gr SWC. Starting with a freshly cleaned bore, I took a couple of fouling shots, then first shot on paper hit almost dead center...COOL!.. then rest was not so cool.
210gr Remington JSP were not much better.
From 50 yards I would think I would be able to keep most shots within the 8 ring.
Majority of the spread is vertical, what would cause that?
So...is it the rifle, bullet/load selection, scope or operator?
KO
the ranch dog molds are designed to combat the marlin gap.
notice the nose it's there to get across that gap and align the boolit with the barrel.
severe vertical stringing is generally caused by velocity variations.
in this case I would say it is the barrel getting a layer of lube built up then the group shifted to where it should be. [I have seen it take over 11 shots to move lube down a barrel to the muzzle and even it out to a consistent C.O.R.E. condition]
I'd say the higher ones are the fouling shots and the bottom bunch is your actual group.
if a lever rifle has a major problem [bedding or inconsistent placement of the front rest] it tends to wander off at angles.
Velocity variations can also be caused by inconsistent or inappropriate crimp or a powder that's not optimal for the situation. I'm a hard-headed German so I'd piddle a bit longer with your load, ko41. I think it shows a bit of promise.
Endowment Life Member NRA, Life Member TSRA, Member WACA, NRA Whittington Center, BBHC
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.
Got one on Monday. Slugged the bore twice and both times was .4105. 410459 sized at .4115 would chamber but 41032 sized .4115 had trouble with when chambering. Hornady 210 HP chambered easily. Does the 41028 have same profile as Hornady jacketed round ?
I think your review is pretty accurate. I bought one back in late January when Davidson had a few to sell to vendors. I paid $800.00 for mine--a premium for "gotta have one in 41 mag" IMO. The gun is beautiful--but mine has continuous issues with screws coming loose after each shooting session. The anodizing on the metal comes off very easily with little abrasion--the trigger pull is a pretty heavy though I expect that to ease up with use. Accuracy is acceptable--but by comparison my cheaper rossi 44 mag 16" carbine will group better at 100--at least so far. If this were any caliber other than 41 mag--I would say this a $650ish quality value gun.
This has had great report and pics. I found a 41 Henry at the LGS ( on Friday 8th) and was actually impressed with the fit and finish. I am still not used to the utilitarian Blue Black finish on several lever guns we have nowadays. But the gun looked better than my Rossi 92. I had been wanting one of these and was excited till I found the price of 850 plus tax. That was going to put me out the door above 920.00 Whoa I just politely handed it back and decided to give this a little time.
If anyone is looking for Lyman mold 41028 , look at Accurate Mold's 41-210A. Of the two boolits ko41 has posted from his molds, the 212 grain one resembles the 41-210A the most to me. In a Marlin 1894 44 Magnum, the RNFD shoots the best when sized larger and I'm hoping 41-210A does the same in Henry.
Last edited by ko41; 04-15-2016 at 03:38 PM.
Any news on your 41, OP?
Endowment Life Member NRA, Life Member TSRA, Member WACA, NRA Whittington Center, BBHC
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call, Lonesome Dove
Some of my favorite recipes start out with a handful of depleted counterbalance devices.
Just been shooting my fun loads out of it with some 255gr WFNGC loaded up got
with LilGun and 296. Makes it a real
thumper. I haven't done anything to it but shoot it. Several hundred rounds down range now. I never did get it scoped as I've had too many projects going on and everyday I'm off I've got other more pressing things to take care of around the house.
I do really like it. It's no CCL, but will do until Marlin makes a new batch of them.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |