Another tea set. The pot is 10.5 inches tall and weighs 1 pound 10 ounces. The creamer and sugar are 5 inches tall, the creamer 7.5 ounces and the sugar 10 ounces. Interesting hallmark on this set... A faint original maker's mark that I can't make out heavily over stamped by the Gimbel Brothers.
Last edited by imashooter2; 10-11-2015 at 11:20 PM.
Another Old Colony pitcher, exactly the same as the one in post 142, except this one is a little heavier at 1 pound 8.6 ounces...
Last edited by imashooter2; 10-11-2015 at 11:22 PM.
I've picked up a few more pieces lately as well... I've been doing pretty good at one particular Goodwill store... had a new piece every time I go in there. Although I've passed on a number of pieces as well because of price.
Just yesterday I picked up a 7.75 oz ash-tray Proofmarked "TIN" & "Made in Denmark". Had to spring a whole $1 for it.
Picked up a 6 oz belt-buckle for $.50 and a small "Jefferson Cup" marked "Pewter" "Made in Italy" for $.25...
So far, ALL of my pewter scores have come from Goodwill stores... 90% of them from the exact same store that seems to get all sorts of good stuff in...
Well done sir. My best finds have been there too.
My Feedback thread:
http://castboolits.gunloads.com/showthread.php?249515-prsman23
Found some stuff with new hallmarks...
A 9 inch decorative plate with the classic angel hallmark, 1 pound 8.9 ounces.
A pair of Jefferson cups, 5.9 ounces each.
Another coffee and tea set. 9 inch coffee pot, 1 pound 7.5 ounces. 7 inch tea pot, 1 pound even. 5 inch sugar, 9.3 ounces.
A small salt cellar. Only 2.6 ounces, but a neat Italian hallmark.
And yet another coffee set. This one was a good score... The 10.5 inch pot is 2 pounds 7.2 ounces. A 4 inch creamer at 10.3 ounces. A 5 inch covered sugar at 12.3 ounces. All on a 13.5 inch tray at 2 pounds 8.8 ounces.
Last edited by imashooter2; 10-11-2015 at 11:24 PM.
A fine example of "not pewter." That's Wilton Armetale, a proprietary aluminum based alloy that is of no use to boolit casters. Tell tales (besides the RWP hallmark) are the thick body and cast in handle.
That's a good one with the classic markings. Thanks for the additions!
You'll notice on this piece that there's a rolled edge above the ring that has 'ENGLISH PEWTER SHEFFIELD'. If you peel that rolled edge outward you can remove that ring, which is sometimes aluminum, and the glass bottom along with the caulk. Old mugs used caulk similar to stained glass caulk but the new ones use a silicon based seal. I try to remove as much of caulk before going into the pot cuz it does very little to flux/reduce the melt. After the ring is removed, the glass comes out with a little steady pressure from the inside on one edge. That mugs enough pewter to add to 2-10 pots of alloy. I peel that rolled edge with a pair of pliers.
I was shopping for pewter for the first time yesterday. I found a lot of things that looked promising, but was afraid to commit. A thin seashell shaped piece with three candle holders (soldered on), and thick legs (also soldered on) but no hallmark. Do ALL pewter pieces have a hallmark? I saw one piece that had a funny looking 'K R', but I didn't see that mark in this thread. There were two 'teacup' sized bowls, obviously turned, by the machine marks. Is any of this pewter? Some stuff said Sheffield Silver, and seemed really cheap for silver. Is there any value to scrap silver?
One way to look at it is that you are learning. If the piece you are in doubt over is only a few bucks, consider it tuition and buy it. Then study it, compared to a hallmarked piece of similar condition and finish. Melt and cast the pieces separately. Use a boolit mold and compare weights and such (like melting points).
Over time, you will get a good feel for unmarked pieces. You still want to quarantine unmarked stuff and check it by melting it. Look for it to melt under 450 deg.
Jeff
Another couple of weeks of good scrounging. Found some weight, but mostly the same old marks. A few new ones though...
An 8 inch diameter bowl, just over a pound. The hallmark is something I'm seeing more of these days, acid etched rather than stamped.
Another 5 inch tankard. This one has a solid bottom and goes 11.3 ounces.
And yet another tea set. 10 inch tray at 15.3 ounces, 3.5 inch sugar and creamer at 9.7 and 8 ounces respectively. And the 9 inch tall, 4 inch diameter pot at 1 pound 14.3 ounces.
Last edited by imashooter2; 10-11-2015 at 11:28 PM.
My latest findings for the melting pot from a deceased estate.
The candle holder by Metl-craft Australia doesn't appear to be weighted at 11 ounces and has someones drivers license number engraved in it for theft prevention. The two small Selangor Malaysia cups are quite thick and weigh in at 7 ounces each.
Mug by Strachan is 9 ounces, not sure where this one is from?
A small pitcher by K.M.D Tiel Holland at 7 ounces.
Goblet, Huntly by Silcraft Melbourne Australia is 5.2 ounces.
Total 39.2 ounces, I paid $20
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |