I'm think'in that handle will allow the operator to be seated more in front of the LNL and not so much to the side.
Is that correct?
Keep em coming!
Crusty Deary Ol'Coot
I'm think'in that handle will allow the operator to be seated more in front of the LNL and not so much to the side.
Is that correct?
Keep em coming!
Crusty Deary Ol'Coot
I have owned all three the LNL AP – 550B – Xl650. While they will all make more ammo then an average person could need. The lnl took the most time to fiddle with stuff during a loading session. I never made 200 rounds without having some little issue. The 550 is a lot more reliable. You do have to keep the priming system clean. By the time I hit a thousand rounds I would take the priming system apart and clean it. Then I was good for another thousand. The 650 is the most solid of the three and just cranks out rounds like nobodies business. Its easy to get two to three time the output with the 650 as the other two presses. The real issue is the price difference. If you can afford the 650 then it’s the best choice. If not get the 550. The LNL would be my last choice. It is fine as long as your not in a hurry and you don’t mind fiddling with the press as needed.
Hornady Lock N Load AP
The Lock-N-Load AP is an auto-indexing, 5-station progressive press that features the Lock-N-Load bushing system, which allows calibers to be changed very quickly. The Lock-N-Load is the cheapest press to equip with additional caliber conversions. During Automatic Indexing Each station moves 1/2 a stage on the upstroke and 1/2 a stage on the down stroke and the up stroke, making for a smoother function. This means less chance of flinging powder out of cases. The Lock-N-Load AP can be used with or without a case feeder. This allows you to start at a Dillon 550B price but to upgrade to a Dillon XL650 speed press at a later date. The earlier editions of this press were known to have issues and were more in line with Lee quality presses. With the new generation of presses Hornady is trying to go head to head with Dillon including matching their warranty.
One Hour Production Rate 500 with case feeder 800.
Cost $ $381.99 bullet feeder 279.99. 12 2010
The Dillon RL550B
RL550B is manual-indexing four station progressive press. The Dillon RL550B is the workhorse Dillon press line. It can load almost any center fire rifle or pistol cartridge. It has 120 caliber conversions available for it. In the Dillon line the Dillon RL550B is the most economical add calibers to. It has less expensive caliber conversions than other Dillon presses. If you were buying just one Dillon press and wanted the most bang for the buck, it would be a Dillon RL550B. According to Dillon more RL550s have been sold than any other progressive machine in the world.
One Hour Production Rate 400 - 500
Cost $376.00 12 2010
The Dillon XL650
The XL 650 is auto-indexing five station progressive press. The XL 650 was built from the ground up to be an auto-indexing press with a case feeder. The Dillon XL650 comes standard with a tube system for an automatic case feeder. The automatic case feeder is sold separately So the advertised starting price doesn’t accurately reflect the true price of a Dillon XL650. A fully set up Dillon XL650 cost twice what a Dillon RL550B cost but produces twice as much ammo an hour. The caliber conversions for the Dillon XL650 are noticeably more expensive than the RL550B and the LNL. For large volume reloading, versatility and ease of use a Dillon XL650 is hard to beat.
One Hour Production Rate 800 – 1150
I owned the 550 and decided it was time to upgrade to a higher production machine. After looking at the 650 and LNL on paper I decided to go with the LNL with case feeder. I bought the LNL with the intention of getting it set up and running good and then selling the 550. Instead the LNL went back. Then I bought the 650. It didn’t take any time to realize the 650 was the best of the batch and I sold the 550.
I bought the LNL thinking I would save some money over the 650 and in the end I ended up spending more in the long run.
Thanks for posting.
I have heard this exact same posting before from other people. Had 550, bought a LNL, had issues and/or it didn't live up to their standards, sold it and bought a 650. When I see different people going through the same situation, it starts to tell me that maybe I should listen and learn something.
Another scenario I see is most get the LNL with the thought that the case feeder MAY be an option in the future. It appears to be a great choice because it is usable without a case feeder and then upgradeable.
I thought the same exact thing when looking at them. In the end though, the 650 is the better machine with a case feeder, why not just use what you got for longer, save up and get it.
Once you compare costs with everything being similar, case feeder, primer alarm, PDX dies etc.... the LNL really isn't any cheaper than the 650.
Last edited by High Altitude; 05-08-2011 at 01:05 AM.
That is true only if you buy the case feeder for both.
Comparison with shipping included:
L-N-L with shell plate & dies = $490
L-N-L with case feeder, shell plate & dies = $810
Dillon 650 with dies = $644
Dillon 650 with case feeder & dies = $862
Dillon 1050 with case feeder & dies = $1665
A basic setup is $150 cheaper on the L-N-L. The Hornady case feeder is $100 more than the Dillon; which is disappointing. This brings the two within $50 of each other. But when you start adding more calibers, the Dillon will be more expensive.
I have a L-N-L and am happy with it. The only issues I have when reloading are:
- The case feeder sometimes does not get a case into the shell plate. This happens about approx 1 in 50 loads and only takes a couple seconds to reach in and put the case in.
- The shell plate has a little wobble in it. This results in a difference in 0.01 OAL when you are setting up with only one case as compared to having all stations working.
- The twist lock for the powder feeder works itself loose and I have to lock it back down about every 30 rounds or so. Again, this only takes about 5 seconds of stoppage but it is stoppage. This is fixable but I haven't done the fix yet.
Someday I'm sure I'll get a Dillon as well. I just don't know whether it will be a 650 or 1050. I don't really need the volume capability of the 1050 but I do really like the additional stations to spread out operations and add more checks into the process of loading.
OP: Thanks for taking the time to do this.
Cranium: Thanks for the info on the roller handles!
Everyone else: To quote an acquaintance on another forum, "Red, blue, green it doesn't matter. If it works for you and you are happy with it then more power to you."
The Dillon 550B is da bomb for most cartridges. It's sadly lacking when it comes to short bottleneck rounds.
"Of all the things I've lost, I miss my mind the most." A. Brilliant
hmmm....how so? On my hornady, I use 5 and could easily use 7. I figured the 1050 could handle that.
Current setup (will have to change it once my bullet feeder comes in):
- Size/deprime
- Powder/expand
- Powder check
- seat
- crimp
Ideal setup:
- Size/deprime
- Powder
- Powder check
- Expand
- bullet feeder
- seat
- crimp
It would also be nice to have more stations for more checks on
- Empty Case
- Primer Removed
- Primer Inserted
- Bullet in case
But this would be getting more into what a commercial production machine does. I think it would be cool to go out to the garage, fill the bullet hopper, fill the case hopper, fill the primer hopper, dial in how many rounds you want and push start.
Why would you want to place the powder drop before the expander?
I'm curious, since I once every 300 cases or so get a nasty mark on my .44 Mag cases in the Hornady Case Activated Powder Drop. Maybe putting the expander after the powder drop would fix that...
I can't speak about the .25-20 but I do load .30 Mauser on my 550. My only problem was caused by the low quality of Lee dies that I bought to "save" money. Once I got rid of them and installed a set of RCBS or Reddings (don't remember which at the moment) the little bottle neck cases moved through without a hitch at the same rate that I can reload 9mm or any other tiny case.
OK I got the primer issue figured out for the Most part on the LNL. It still is not as relable as my 550B though. It seems it has to be kept cleaner. Not bashing the LNL but now I am having indexing issues. I want this thing to work but its just one thing after another so far.
Also why would you place the boolit on the brass in one station and then index it to another station to seat it? Seems to me if you are using the minimum amount of flare needed for your brass that the boolit will not be sitting in a proper orientation by the time it is indexed to another station. Over complication, set the boolit and seat it in one station.
On indexing on the LNL, as per the Hornady folk, make very small adjustments to the pawls!!!!!!!!!!!!!!!!!
Being a, "If a little is good a lot is better", type person - always did have problems with 1/4" bolts! - I origionally did the half or one turn type of adjustment.
NOT!!!!!!!! in this cast, "a little goes a long ways"! And that is all it takes.
Keep em coming!
Crusty Deary Ol'Coot
I was under the impression that one station on a 1050 was a dedicated primer pocket swager? MBW? If so that leaves you with six stations. Also I agree with others that with a dillon powder measure and their powder funnels there is no reason to expAnd and drop powder in two separate stations. It's easy enough to turn powder funnels for custom profiles for cast boolits like Lyman M dies but I have to admit that I have been lazy and use their standard funnels for my .45 colt/.357/.380acp cast boolits with no issues.
I would drop powder and expand in different stations if I had the available stations to do it. Just as I do today with seating and crimping in different stations. Keeping each station doing one sole function allows for easier adjustments and identification of issues. But this is just my general opinion.
Bullet feeder requires a station.
Sure the feeder requires a station but is it not the same station you seat in? Maybe the feeder you are talking about is different from the kind I have seen. Even the GSI feeds into the same station that seats.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |