12GA FH Slug Tester --

[hubel458]

Load of 12 triple ought buckshot in 8ga. They are
70gr each, total 840 gr, and over 2000 fps with
125 gr of 4759. Ed
Here is URL for the waterpail busting video above--
http://www.youtube.com/watch?v=rUNHszY4ACM

[hubel458]

There are now two videos of 12GA FH on YouTube,
exploding big heavy walled pails of water.
The "Grampa's Cannon" one with a long view,
and "Grandpa's First Shot" a closeup video,
the first one, that shows how the top of heavy
shelf got bent. Later kids will do videos showing
muzzle blast and recoil.
Also the 3 ought buckshot from the 8ga load
above goes through 2" hardwood ok. I will test
8ga on waterpail also, to see what happens. Ed

[hubel458]

Here is pic of Mossberg 695 that will be the
second 28GA From Hell.You can see long
brass case in the port.Here is URL of
the "Grandpa's First Shot" video. Ed

http://www.youtube.com/watch?v=c48zTpsgbuk

[hubel458]

Here is closeup pic of Rob's 12GA FH, a Borchardt falling block
action. Real nice. In picture is along brass 12ga case with one
of Rob's 2000gr bore rider, solid, streamlined slugs. Ed

[hubel458]

Got my long 700 HE case chambered barrel
finally in a bmg size action. It is barrel
I locked onto an I-beam and got testing and
load developement done over the last couple
years. Max load about 23,000 ft lbs.
It weighs 27 lbs, laminated thumbhole stock,
a max size pad, weighted butt, a reinforced
wrist, recoil barrel ring on front of stock.Ed

[hubel458]

Here is picture of a neat scaled up Sharps replica
that would handle out 12GA FH and my 700HE.
That outside hammer looks great. From a magazine
article in Very High Power...Ed

[hubel458]

Here is a pic of a projectile idea Rob had. We will test it later
this fall, It is 12ga bore rider design Body is Aluminum, and it
will have a heavy 50 cal insert in the nose made from tungsten
or similiar metals. In the picture he put a 50 cal bullet in for
show. The insert in the nose will be flush with front of the
AL carrier. It should be stable at slow twists and if built
with back and front same diameter stable in smoothbores.
The long lighter tail-end compared to heavy nose insert
will make it stable. Same principle Brenekke uses. This idea
is being explored to try to get superior penetration
from 12ga, with heavy, hard insert in the nose.Ed

[hubel458]

Here is another view of my 700HE blaster,
that I got rigged up on an action and stock.
Side view shows action with a aperture sight I
rigged up. Also cases. On left is 700H 3.25" case.
Center my 700HE, what the gun in picture has now.
Good for nearly 23,000 ft lbs, we attained in
a work up in testing with the barrel as a test
barrel with screw on testing receiver....Ed

[hubel458]

Here is picture of another dart type 12ga slug Rob made. Body
is aluminum, it has a heavy tungsten carbide insert in the
nose. The TC in the nose is about 5 times denser than AL.
Total length is 2.35 inches, weight about 950 gr. The .75" long
insert a real tight type fit. Heat AL, put in insert, cools, locks on.
It is fairly streamlined, yet has wide meplat for penetration
in game. Flat points penetrate straighter in game.
It is hollow inside in the back, behind insert which puts the
center of gravity way up front, it should fly straight even from
a smoothbore. They are fast to make and material
less expense than copper.In pic is a copper and a brass 600
cal slugs for comparison. Dart/slug on right has insert.
Now for an explosive expansion version of the same concept,
you'd pour soft lead in the nose in place of hard insert..Still be
nose heavy to be stable. Ed

[hubel458]

Here are more samples of nice 12ga slugs.....Here is pic of
ones RG Henson sent. Jacketed 12ga. 715gr hollowpoints,
on the right and in front a jkt 675gr hollowbase.
RG's number 1-770-366-4846. These will be great for
shorter plastic and brass cases as well as long cases.
Other slugs in pic, in the back, left to right
Foster 436gr- Dixie 600gr- 750gr brass- my 750gr hollowbase
brass, and a hollowpoint I put a lightweight filler in the nose
for streamlining..Ed

[hubel458]

We get asked about availability of our long case.
So, any of you who might want some of the 12GA FH
brass cases made from BMG brass, we have the fellow who
had the idea about the 12GA FH first, Rob on AR forum,
is planning on making them. He has got the machines to do
it now, that we didn't have before. Let me know how many
you are interested in getting, so he can plan and figure
the best way . He has a bunch of BMG cases to start with,
he and I have places to get more.I'm posting this all over.Ed

[hubel458]

Testing 715gr jacketed hollowpoint from RG Henson in Savage 210.
With 30 inch barrel, long brass 3.85" case, big primer.
Slightly hairy load 290gr RL22--2700 fps. Shot moderate load
of 300gr W-860 -- 2400 fps for 3 shot group of 3" at 50
yards with my bad eyes and peep sights. They shoot nice, they go
into target straight.. Other nice thing the price from RG,
for customers getting in on his first run, $1.25 plus shipping.
That is less than half of what other big bore jkt bullets cost.
Call him for some great slugs. They are great like
the Dixie slugs. Ed

[hubel458]

Lookee what another santa sent me.
A regular BMG case on the left, and
a straight BMG case on the right, and it
CAME FROM THE MANUFACTURER THAT WAY.

It is primer cartridge for large guns and howitzers.
It is used in those guns/cannons that have powder in big bags.
It is filled with powder and inserted into cannon breach and
when fired sets off the larger charge. On some cannon breaches
they have an automatic feed for these with a huge 40 round
drum magazine. This on is marked IVI 89 C67. IVI is Canadian.
On these breaches it is held by collet fingers for head space
and for ejection.

Ok, there are many thousands more of these out there than the
PROP cases I showed before. We need to find few barrels of these
and have Rob, etal, put on rims.... no annealing.....no fireforming,
just slight resize to 12GA FH. Please help if you know of any.
They would save so much work and time..And even though fired
the bases are perfectly straight, another plus.....Ed

[hubel458]

Going to test various of our slug loads in a 12ga Encore
Prohunter this month, see if it does like the NEF Ultra.Ed

[hubel458]

We will be testing a fellows 1400gr slugs for
getting safe loads for him, in 3.5" plastic.
Also in a couple months Rob, who's idea the 12GA FH
was will be able to deliver the super strong 12GA FH
cases made from BMG brass. And the they will be
headstamped, all done by his CNC machine.Ed

[hubel458]

RIP on AR Big bore forum is doing 835 Mossy and 1400gr Darwin cast slugs.
A 14.5 pound Ulti-Mag. The hollow part of the butt is filled with about 5.5 lbs of lead shot and epoxy. Has 4X Sightron in QRW rings. Do 3.5" plastic hulls with the Darwin in it first. It balances on the trigger. Loading the magazine with 4 and one up the spout will add about 1.25 pounds if the 5 rounds are "Darwins," and move the balance point to the front of the triggerguard.
It is heavier rifled 24" chromoly alloy barrel.

Brett in MN has Mossy 835, only with smoothbore barrel and gets
1oz finned plastic tail Ballistic Products slug to 2300 fps,
using shotgun powder.Ed

[hubel458]

Still testing 8ga I have setup in the Enfield.
It has a long smooth barrel. Those 8ga
heavy plastic cases are great. Fire them 4 times with
no resizing. Here is pic of cast slugs used in 8ga..
One and two are 1015gr hollowbase. Three and 4 are
875gr hollowbase. On four the cushion base is cut off
so I can use card wad and have more room for
powder.Ed

[hubel458]

WE test both plastic and brass 3.5" cases to compare.
We got our RMC 3.5" brass 12ga cases. These are turned
cases using shotgun primer. They have nice thick base,
and a good radius in the corner. Got a Brenekke OK 437 gr
slug to 2800 fps, a 540gr Hammerhead slug to 2450. got 600gr
Dixie to 2300, the 715gr RG jacketed to 2130, and a 1400gr
Darwin to 1400 plus. Tested in NEF. Shot one case 15 times
and still going strong, tight primer, with loads running about
20- 24,000 psi.I have pics of cases soon, and we also will
test these brass ones and 3.5" plastic in 12ga Encore
Prohunter..Ed

[hubel458]

Here is picture of RMC 3.5" cases with variety of slugs,
locked on wad slugs and sabots. There are 3 of our long cases
in back for comparison. The RMC turned cases have shotgun
primer. Case # 4 has 437gr slug in BPI SABOT( finally hard sabots
in 12ga for reloading), #5 437gr Brenekke KO slug, #6 540gr
Hammerhead slug, #7 600gr Dixie hard slug, #8 RG's 715gr
jacketed, #9 750gr solid brass. Ed

[hubel458]

Here is picture of a 12ga hard discarding sabot you can get
for reloading, the BPI. From Ballistic products. In picture
is sabot with cast 437gr Hornady Great Plains 50cal slug I put
in it. Also the 410 gr and 385gr Great Plains work.
Finally able to load your own instead of paying 3-5 bucks
each for loaded rounds.You can use the 500 S&W bullets also
as well as shorter 50 cal blackpowder slugs... Ed