Re-Re-Re-Run of MiHec .452 - 200gn Cramer

[rmaster14145]

is there any way to get a drawing of the boolit? if it has a flat point my pistol will not feed them. if it has the least bit of curve on the end im all good.

if i can see a drawing and the end is NOT flat im in for one too.

thanks

rm

[bgokk]

if i can see a drawing and the end is NOT flat im in for one too.

thanks

rm

There is a pic in the first post showing each of the HP styles. Flip over either set of pins and you will have a FP.

[hunter64]

Ordered mine. Not missing this one again,lol.

[Cord]

Our complements to Springfield,
from the "Casting with...." thread:

[Depdog]

Just checking myself here. When everyone else us ordering off the link that Miha posted are you just getting the page for your email, username etc and when you enter it, ut goes to the thank you page? (that's what I get). Or do y'all actually get a PayPal page and pay for it?

Thanks
Glenn

[bgokk]

Just checking myself here. When everyone else us ordering off the link that Miha posted are you just getting the page for your email, username etc and when you enter it, ut goes to the thank you page? (that's what I get). Or do y'all actually get a PayPal page and pay for it?

Thanks
Glenn

MiHec will send you a message when he is ready for payment. You have placed your order. When he is ready to ship he will bill you (pay pal) that's when you pay.

This is from past orders. I have two of MiHec's moulds.

[Tippet]

is there any way to get a drawing of the boolit? if it has a flat point my pistol will not feed them. if it has the least bit of curve on the end im all good.

if i can see a drawing and the end is NOT flat im in for one too.

thanks

rm

Aside from the drawing on the first page, and other pics shown, here are a couple pics of what this mould has done for me...I really like this one a lot. I'm going ahead with another order. I recommend an extra set of pins. The pins are machined to very fine tolerance. With my first of these moulds I damaged one of the pin sets . I don't think I'd do it again now that I know the lay of the land. In any case it can't hurt to have a back-up.

[Bulltipper]

garsh those shure is purdy...

[Finster101]

What lube are you guys using on this boolit?

[Bulltipper]

I have to have another. oh man is the old lady gonna be pissed. I guess I better sell something. I wonder how much the dogs are worth...?

[John D]

What lube are you guys using on this boolit?

I'm using Carnuba Red with good results.

[Duckhunter]

I NEED one of these. Add me to the list.

[Cord]

Update:

Feb 20, 2010:

We are in the "closed" order stage,
waiting for payment requests from
the MP Molds website.

.

[Tippet]

I have to have another. oh man is the old lady gonna be pissed. I guess I better sell something. I wonder how much the dogs are worth...?

Kevin sell the cats, people used to get the finest fly lines from their innards...you'll need to rely on the dog when you find yourself out into the cold...

[rmaster14145]

tippet, THANKS for the pics. i ordered one already even without your close up pics..

when i ordered i did not see a place to add extra pins. how do you request ( buy ) an extra set ( or 2 ) of pins?

rm

[gray wolf]

So many pages I don't know if this was asked. Can we set this mold up to do one hex and one round hole bullet at the same time??

[John D]

So many pages I don't know if this was asked. Can we set this mold up to do one hex and one round hole bullet at the same time??

Yes you can.

[bgokk]

tippet, THANKS for the pics. i ordered one already even without your close up pics..

when i ordered i did not see a place to add extra pins. how do you request ( buy ) an extra set ( or 2 ) of pins?

rm

The mould comes with round and 5 sided pins either of which can be inverted and then cast a FP. That is my understanding.

PS: You might PM MiHec and request more pins if the 2 sets are not sufficent.

[Blacksmith]

I just ordered mine!

[j20owner]

Just tossed my name into the hat, so to speak.