Need opinions about Hornady/Pacific 007 press

[strangwn]

I just saw a new-in-box old stock, never used, mint condition Hornady/Pacific 007 press. It is lightweight because of the cast aluminum frame, but is a very well made and sturdy-looking press. I have not yet found any info, opinions, or market values. Could not find any completed sales on eBay. I'm thinking about buying it, but am seeking expert advice first.

[Le Loup Solitaire]

Hi, I do not have one, but a close friend does. He bought it new a long time ago. It is a solid press and has served him well. He never had any kind of problem with it;just kept it clean and oiled/greased and it does whatever he needs. Its every bit as good as any single stage that is made nowadays. Its a keeper. LLS

[jcw1970]

I've got a 007 and I think it's great. I use mine as a decapper and load my rifle shells on it. I have the auto prime for it and once you get it setup, it works great. I picked mine up on ebay for around $60 with shipping.

[DaveInFloweryBranchGA]

I'm a big Hornady fan and own a Hornady LnL AP, but I would buy a Lee Classic Cast single stage over any other single stage out there, unless you go with a Bonanza Coax and I'm not sure the difference in price gains you a whole lot.

The Lee has an excellent primer disposal system, compound leverage, has the capacity to accept the Hornady LnL conversion kit to allow you the use of LnL bushings, allows you to set the operating handle to what is ergonomically best for you, either right or left hand, has a small footprint, but is made of cast iron and steel. One of the absolute best values in a single stage right now.

Bottom line, unless you can get the Hornady for significantly less than the Lee, I would choose the Lee. It's the press that beat out my RCBS Rock Chucker for the place beside my Lock N Load progressive.

Regards,

Dave

[Deekes]

Don't know where you got cast aluminum there friend. Must be a J A Pan model.

[Deekes]

Another note, after 40 years, you can still buy parts for them.

[pworley1]

Mine has been one of my most used presses. It has never had an issue. I gave $45 for it years ago on ebay.

[r1kk1]

I'm a big Hornady fan and own a Hornady LnL AP, but I would buy a Lee Classic Cast single stage over any other single stage out there, unless you go with a Bonanza Coax and I'm not sure the difference in price gains you a whole lot.

The Lee has an excellent primer disposal system, compound leverage, has the capacity to accept the Hornady LnL conversion kit to allow you the use of LnL bushings, allows you to set the operating handle to what is ergonomically best for you, either right or left hand, has a small footprint, but is made of cast iron and steel. One of the absolute best values in a single stage right now.

Bottom line, unless you can get the Hornady for significantly less than the Lee, I would choose the Lee. It's the press that beat out my RCBS Rock Chucker for the place beside my Lock N Load progressive.

Regards,

Dave

Actually there are quite a number of presses out there with primer through the ram disposal and/or can use LNL bushings.

CH4D Champion, Redding, CO-AX, some other vintage stuff out there.

I seen the CC at a shop and it looked nice. I was surprised it weighed around 13 lbs. i thought it weighed much more. I see they have a redesigned linkage compared to the old Challenger which is a blessing.

I really like my four single stages. I'm glad you like yours as much!

Take care

r1kk1

[bhn22]

It's the same press as the current Lock-N-Load® Classic Loader, but without the Lock-N-Load BS.

[avogunner]

I'm also a Hornady (Pacific) fan. My primary press is the pre-cursor of the 007, a Pacific Mulit-Power C. I bought it brand new in 1981 as part of a "deluxe" kit. Just like today's version, it came with the powder measure, case prep tools, etc. but then, it included a set of dies of your choosing (I chose .45acp). It will definitely last me my lifetime and I'm sure my sons too.

[Pablo 5959]

I have a very old "C" type, but older. The ram is the shell holder. The Hornady tech said they don't make parts for the Pacific any more. So caution with that buy. Had to machine the ram a little to accept a shell plate. I love this press, but then again I rescued it from the scrap pile.
This is a pic of it the day after paint.

[Jack Stanley]

I bought a 007 back when they made them new and I've been very happy with it . It works smooth , no rough edges and everything fits right , it takes no fooling around to make it work .

Jack

[bhn22]

Honestly, I'm the only person I've ever known who has worn out a a 007. It took decades to do, and I can't even imagine how many rounds I loaded on it. This was in my IPSC & IHMSA days, so it was a formidable amount.

[pworley1]

I have 2 Pacific 007 presses on my bench right now and would not part with either of them. They were both bought used years ago and have loaded 1000's of rounds since I bought them.

[Jack Russel]

I have one I use for sizing bullits and reloading rifle. Great very strong press.

[15meter]

10 years between posts.

And I thought I resuscitated some old threads.

[racepres]

Obviously "search" works here...That is a Good thing...
For the next person "knowing enough to Search"....My 007 is very old, very trusted, and never leaving!!!