I would be in for one. What is the status of this buy. I had to check the 3rd page to find this buy.
Bigscot
I would be in for one. What is the status of this buy. I had to check the 3rd page to find this buy.
Bigscot
Hunt hard, shoot straight, kill clean, apologize to no one!
-Ralph M. Lermayer-
Editor of Predator Xtream
I would be in for the the RN, not the SWC. It has to feed in my Win M92.
Rich or poor, it's good to have money.
I'm with Hiram and several others about the RN , and understand that another thread was under way regarding that mold. With apologies for the intrusion on this thread, I was wondering if there was enough interest in the other design to proceed.
I think there is adequate demand for a RNFP. There is a thread for a gaschecked RNFP that didn't quite make the numbers here: http://castboolits.gunloads.com/showthread.php?t=52712
It did get about a dozen votes in the big poll. Maybe it could be reworked slightly to increase demand or maybe more people would prefer a plainbased design.
Nothing to do but run it up the flagpole and see who salutes.
Last edited by only1asterisk; 07-23-2009 at 10:33 AM.
Happy to hear we are on MiHec's list for this one !
I have my money in my hand and waiting for him to post the Group Buy info on his website!
Jerry
"Something very close to yours, but it weighs 179 gr. as a HP and 210 as a solid."
S&W .38/44 Outdoorsman Accumulator
Jerry,
If you haven't already, you need to do a little how-to on taking pictures like that.
The design of the above bullet would not feed reliably in my M92 because the front band is like a ridge to get hung-up on. The other design had a smooth curve to full diameter.
Rich or poor, it's good to have money.
Put me down for one of post #13, for the .44 Special; I like the Mihec HP molds.
Having completed my reading assignment , I also created a new thread for those (like me) who are also interested in a Mihec mold based on post #3 of this thread.
http://castboolits.gunloads.com/showthread.php?t=58706
I am still interested in this one, once it gets going.
Just bumping this thread.
I am interested in the SWC design as in post 13, either as a solid or HP.
Has a decision been made on any of the specifics. The picture on post 13 for the bullet. How about mold material, # of cavities, GC or not , cost.
I just got my computer back after the lightning damage so i am behind a little
Please put me down for one unit, brass, two cavity with HP pins. One of these days I'll have to stop and count how many molds I have on order. I think it's 4 or 5. Wow. Wonder if Lyman is paying attention?? Enjoy Mike
Is this an active buy thread or an interest thread?
Boolits= as God laid it into the soil,,grand old Galena,the Silver Stream graciously hand poured into molds for our consumption.
Bullets= Machine made utilizing Full Length Gas Checks as to provide projectiles for the masses.
http://www.cafepress.com/castboolits
castboolits@gmail.com
I believe we were waiting for Miha to accept it, but I'm not sure that happened; did anyone contact him?
45nut
Looking through the post it appears that only1asterick has contacted MiHec and we are inline for this mold (post #70 and #82) but other than that there has been no other comments.
I just looked on MiHec website and it appears this is in his list of upcoming group buys.
Money isn't being collected yet, but we are in line. MiHec will announce when he is ready to begin taking money.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |