Hi folks!
I am looking for 7.62 Nagant/7.62x38R cases. If someone has some they would be willing to part with, please let me know!
Thanks all!
Hi folks!
I am looking for 7.62 Nagant/7.62x38R cases. If someone has some they would be willing to part with, please let me know!
Thanks all!
I recently bought some from these guys: https://store.mojoprecision.com/prod...2&_ss=e&_v=1.0
There were a couple of Berdan cases in the mix but otherwise a pretty good deal.
My "Swappin & Sellin" feedback thread: http://castboolits.gunloads.com/show...light=btreanor
I don’t wanna get your hopes up but I had about 30 pieces of it for the longest time. if I can remember where I put it and if I still have it I’ll send you a PM you can have it. I’ll gladly send it to you. I saved it because I knew I’d find somebody that needed it someday.
Long, Wide, Deep, and Without Hesitation!
Currently casting and loading: .32 S&W Long, .38 Special, 9X19, .357 Magnum, .40 S&W, .45 ACP, 10mm, 44 Special 44 Magnum. .223, 7.62x39, 7.62 x 54R, .30-06, 45-70, .32, .36, .44. .45. .50. .54. .58 and .60 round ball and various minies. And .375 heel crimped conical for those .36 conversions . KB6MRP on Discord
I have 50 new PPU I just ran across.
I'll see if I can remember where I put them!
see below, in stock and a great company
Last edited by HARRYMPOPE; 03-28-2024 at 08:40 PM.
Your mother was a hamster, and your father smelt of elderberries
Your mother was a hamster, and your father smelt of elderberries
Deleting my post as well; was written very poorly, so could easily be taken the wrong way.
Thank you & best regards,
Last edited by Kestrel4k; 03-28-2024 at 11:37 PM.
Please delete my comment I misunderstoo
Last edited by HARRYMPOPE; 03-28-2024 at 11:34 PM.
Your mother was a hamster, and your father smelt of elderberries
Yup, this is the brass for the Russian revolver. However, I'll be using it to shoot in my Winchester 1905 in 32WSL.
Thank you for the link to Buffalo Arms. I checked 2 weeks ago and they were out. I'll use them if no one here has any. Not that I object to Buffalo, I would like my money to go to someone on the forum first.
I’m still looking!
Long, Wide, Deep, and Without Hesitation!
Sold all mine with revolver so sorry. Word of caution tho, beware of Bertram brass........hi dollar and all I had started splitting badly as NIB.........., suggest annealing on acquisition.
How many are you looking to have? I believe 32-20 wcf can be used. you might check the archives for load data etc.
I once had a WWII Russian bring back by a GI. I cast 32-20 wcf boolits out of a factory mould. I sized and lubed em. Used 32-20 brass and my cast boolits. They shot great. Think I even used a set of Lyman 310 dies in an old press.
32-20 is a little too short in my die set. It will not crimp. Thank you for the suggestions!
I just bought 100 pcs of 32-20 for my WSL .32. I use a WSL 32 die and a 32-20 die on the 32-20 brass.
Bump for the weekend!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |