Hi,need some informations,use to casted with lee 9 mm mold,but now when sized with my lyman .356 i get this (pictured)are the mold are to old or its me.thank for your info.
|
   
   
|
|
Hi,need some informations,use to casted with lee 9 mm mold,but now when sized with my lyman .356 i get this (pictured)are the mold are to old or its me.thank for your info.
Last edited by 84mmcarl-gustav; 07-25-2023 at 09:00 AM.
Si Vis Pacem, Para Bellum
Start off with 357 sizer and your results will be much better
Looks like the mold halves may be out of alignment.
Maker of Silver Boolits for Werewolf hunting
+1 to Hickok's comment.
+1 to Recycled Bullet's comment.
I find .357 shoots best in my guns. As to the boolits, they do like like there is some issue with mold alignment. Are the pins and their holes worn? If so you might be able to drift enough material back into the holes to shore them up. But it may be a temporary solution...
Currently looking for a Lyman/Ideal 311419 Mold - PM if you have one you'd like to get rid of!
JDGabbard's Feedback Thread
"A hand on a gun is better than a cop on the phone," Jerry Ellis, Oklahoma State House of Representatives.
The neighbors refer to me affectionately as, "The nut up on the ridge with the cannon." - MaxHeadSpace.
Jdgabbard's very own boolit boxes pattern!
This. Sizing is not the problem.Originally Posted by Hickok
Don Verna
Maybe a sliver of lead between the two sides of the mold?
Are they coming out of the mold like that or out of the sizer like that?
Also noticed a large wrinkle on the nose of the bullet on the left. Cold mold? Interrupted pour? Measure the bullets as they drop from the mold, pre sizing, after fixing mold alignment, to see how much you need to size...
My Anchor is holding fast!
Hi,thanks all,I will try to realign the mold and see what happened.
Si Vis Pacem, Para Bellum
do ya got a picture of one that hasn't been sized?
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
I agree with the others. I don't see how a sizing die and top punch could leave a straight line from the tip of the bullet to the base. I agree with giving the mold a real good cleaning and inspection.
A vote for anyone other then the conservative candidates is a vote for the liberal candidates.
Hi,finaly it out of line and it will be easier to buy a new one,thanks.
Si Vis Pacem, Para Bellum
Never touched a Lee mold, but some molds can be brought back into alignment by adjusting the the depth of the alignment pins. This is because the taper of the pins is relied upon to control cavity concentricity.
What pistol are you firing these in? My Walther & Beretta 9mm barrels are all .3575" groove diameter or so. I also have an FN HiPower race gun with a barrel that is about .3575" groove diameter, but if I assemble such a Lead bullet in a 9mm case, it will not chamber, so it gets Jacketed only.
How are you measuring your bullets? My experience with cheap Chinese vernier calipers is that they are frequently .002" off. I trust micrometers.
How many times have you used this mold? Time for a new IRON mold. Maybe SAECO #384 or 115.
Thanks
Lee
Posting Permissions
| BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
| BR | Bench Rest | M | Magnum | RN | Round Nose |
| BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
| C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
| HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
| PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
| LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
| GC | Gas Check |
Reply With Quote